文档包括:
说明书一份。41页，17700字。
开题报告一份。
图纸共4张，如下所示
A1-总装配图.dwg
A2-行星轮.dwg
A3-卷筒.dwg
A3-输入轴.dwg
目 录
中文摘要 VI
外文摘要 VII
前言 VIII
1 绪论 1
1.1 卷扬机国内外现状和发展趋势与研究的主攻方向 1
1.2 少齿差行星齿轮传动计算现状及发展 4
1.3 设计思路及方案论证 5
2 主要设计参数的确定 6
2.1 卷扬机工作级别的确定 7
2.2 钢丝绳直径的选取 7
2.3 卷筒计算直径的确定 8
2.4 电机的选择与传动比的计算 8
3 渐开线少齿差减速装置的设计 9
3.1 少齿差传动原理 9
3.2 齿轮齿数的确定 10
3.3 齿轮模数的确定 10
3.4 齿轮基本参数的确定 13
3.5 传动内部结构的选定与设计 16
3.6 轴的设计 18
4 部分零件的校核 23
4.1 少齿差行星传动受力分析 24
4.2 销轴的强度校核 26
4.3 输出轴的强度校核 27
4.4 键的校核 29
4.5 轴承的校核 30
5 卷筒主要尺寸的确定 32
5.1 卷筒节径、边缘直径和容绳宽度的确定 32
5.2 卷筒厚度与绳槽尺寸的确定 32
6 结束语 34
参考文献 35
致谢 36
附录 37
侧装式少齿差传动卷扬机设计
[摘要]渐开线少齿差传动卷扬机是诸多传动形式卷扬机中的一种。利用少齿差传动机构的优越性可改进和提高建筑机械等设备的传动结构技术性能，将渐开线少齿差行星齿轮传动应用于建筑卷扬机的动力传输系统，可以减小机构尺寸，提高传动质量，同时它的传动比大、承载能力大、寿命长，也降低了制造成本。但是在渐开线少齿差内啮合传动中,由于内齿轮和外齿轮的齿数差少,在切削和装配时常常会产生各种干涉,以致造成报废。因此,为了保证内啮合传动的正常运转,设计时要满足几个条件，主要的两个限制条件是，即要保证不发生齿廓重迭干涉和啮合率不小于1。少齿差内啮合的设计非常烦琐,尤其是齿廓重迭干涉验算最为麻烦，这也是解决设计问题的核心所在。在设计过程中多次变换变位系数和齿顶高系数以满足条件。
本文主要对少齿差行星齿轮传动的设计计算进行了说明。其中包括工作原理、参数选择、几何计算等。并根据结构尺寸设计零件、选择标准件，然后再进行强度或者寿命校核计算。
[关键词] 卷扬机；渐开线少齿差传动；齿廓重迭干涉；少齿差内啮合
Design of the side installment hoist of small tooth number difference planetary transmission
Student: Huang Yunhui School of Mechanical engineering Yangtze University
Teacher: Wei Feng /Huang Qingshi School of Mechanical engineering Yangtze University
[Abstract] Involute gear transmission with small tooth number difference hoist is one kind of transmissions forms hoist. It can improve and enhance the transmission structure technical performance of the construction machinery using the of small tooth number difference planetary transmission. If the involute gear transmission with small tooth number difference transmission will apply for construction hoist transfer system, it can increased besides a reduction ingear size, and no interference will occur, and improves the transmission quality simultaneously its velocity ratio is big and the load capacity is big too, the life is long, and it also can reduce the production cost. But in the mesh inside of forma small tooth number difference transmission, because of the difference of annular gear and the external gear is few. It ofter causes interference in the cutting and the assembly, so that it may be waster. Therefore, in order to in guarantee meshes the transmission noramal work, the design must satisfy several conditions. The two main limiting condition is that it must guarantee does not have the tooth outline overlap interference and meshing rate smaller than 1.The design of the mesh inside of forma small tooth number difference is troublesome, extremely the checking computations of the tooth outline overlap difference. It is also the core of the solution in the design. It need to transform the dislodgement coefficient and the gear addendum coefficient many times to satisfy the condition in the design process.
This paper describes the method which is used for designing the drive of the few difference in number of teeth. Including principle of work, parameter choice, geometry computation and so on. Choose the standard letter on the basis of the structure size design components, then carry on the computation of the intensity or the life examination.
[Key words] hoist machine;involute gear transmission with small tooth number difference;tooth outline overlap interference ;small tooth number difference internal mesh.
川公网安备: 51019002004831号