关 键 词：

RS CMWrun Basic Signaling User Manual CMW操作文档 CMWrun_KT050_UserManual_V1-7-8 CMW 操作 文档 CMWrun_KT050_UserManual_V1

资源描述：

R 2 1176 9293 02 01 Test see Test Configuration The downlink signal generator is not switched on at this stage 2 Inquiry The R see chapter 1 2 2 2 Test Configuration on page 8 The forward link signal generator is not switched on at this stage 2 BaseStationEnable The R otherwise test module execution fails 1 2 6 1Prerequisites Required Equipment Radio Communication Tester R see chapter 1 3 3 2 Test Configuration on page 25 The forward link signal generator is not switched on at this stage 2 BaseStationEnable The R refer to the SCPI report 1 3 7Set Channel Defines a 1xEV DO operating band and channel and checks the two settings for com patibility If the channel belongs to the operating band both settings are used by the R otherwise test module execution fails 1 3 7 1Prerequisites Required Equipment Radio Communication Tester R see chapter 1 5 3 2 Test Configuration on page 64 The DL generator is not switched on at this stage 2 TestSetupAttenuation Default The default test setup Coupler and default attenuation values from the Resources Test Setup dialog are assigned The default values should not be too far from the actual attenuations in the test setup to allow registration of the mobile You can skip this step if the 0 dB default attenua tions of the R see chapter 1 6 2 2 Test Configuration on page 85 The DL generator is not switched on at this stage 2 TestSetupAttenuation Default The default test setup Coupler and default attenuation values from the Resources Test Setup dialog are assigned The default values should not be too far from the actual attenuations in the test setup to TD SCDMA R refer to the SCPI report 1 7 2Call Setup Configures the R see chapter 1 7 2 2 Test Configuration on page 92 The DL generator is not switched on at this stage 2 TestSetupAttenuation Default The default test setup Coupler and default attenuation values from the Resources Test Setup dialog are assigned The default values should not be too far from the actual attenuations in the test setup to allow registration of the mobile You can skip this step if the 0 dB default attenua tions of the R refer to the SCPI report 1 7 9Pattern Test Performs an inner loop power control measurement of an already established connec tion 1 7 9 1Prerequisites Required Equipment Radio Communication Tester R otherwise test module execution fails The two test modules for DL and UL channel setting are similar 1 7 12 1Prerequisites Required Equipment Radio Communication Tester R selection of measurement parameters and results Result tables for all selected results Limit check with configurable limits 1 7 13 1Prerequisites Required Equipment Radio Communication Tester R see chapter 1 8 1 2 Test Configuration on page 114 The DL generator is not switched on at this stage 2 BaseStationEnable The R see chap ter 1 8 1 3 Test Results on page 114 1 8 2WiMAX Signaling Disconnect Turns the WiMAX base station signal of the R see above For further reference Refer to the documentation of the WiMAX signaling application WiMAX R see chapter 1 8 1 WiMAX Connection Setup on page 113 1 8 4 2Test Configuration The property dialog gives access to all test settings The Measurements panel contains a list of the basic results of the test Only the selected results will be displayed in the measurement report Advanced opens a dialog with a more detailed result selection Trigger Level defines the trigger threshold for the IF Power trigger relative to the Expected Nominal Power For further reference Refer to the documentation of the WiMAX multi evaluation measurement 1 8 4 3Test Results The WiMAX Signaling Test Set module provides a configurable list of measurement results characterizing the transmitter TX properties of a connected WiMAX mobile phone All results are obtained at the RF and burst settings that the R S CMW used to set up the connection The results are displayed in the Measurement Report tab Limit check results All measurement results are compared with the current limit settings of the R S CMW If a measurement result is between the lower and the upper limits the limit check indi cates Passed otherwise it indicates Failed The Yield tab shows an overall pass fail message For further reference Refer to the documentation of the WiMAX multi evaluation measurement 1 8 4 4Test Module Details The WiMAX Signaling Test Set module initiates an analysis of the received uplink WiMAX signal from the connected mobile A power trigger is used to capture the uplink subframes After a reset of the R S CMW the settings of the WiMAX Signaling and the WiMAX Multi Evaluation applications match The R S CMW expects a peak input power of 0 dBm You may have to adjust the Expected Nominal Power setting of the WiMAX WiMAX R S CMW KT050 Basic Signaling SuiteR S CMW KT050 119User Manual 1176 9293 02 01 Multi Evaluation measurement if the transmitter output power of the connected mobile is above or far below 0 dBm WiMAX

内容简介：

-