QJ350009S0-屏规格书.doc

深圳市岐嘉光电有限公司产 品 规 格 书SPEC-QJ350009S0-A23-07-2011PAGE 18 OF 17 Project No.项目编号QJ350009S0Customer客户名称胜诺达Module No.客户型号M5-3.5Product type产品内容Standard LCD ModuleTFT：320x 3RGB x 480 Dots3.5”TFT LCDSignature by customer: 客户确认签章：编 制电子审核结构审核品质审核批 准刘鸿杰刘 波谢 群深圳市岐嘉光电有限公司地址：深圳福永塘尾建安路正昌达数码科技园A栋3楼电话传真邮编：518000网站：Http/:E-mail: CONTENTSPage No.1.DOCUMENT REVISION HISTORY32.GENERAL DESCRIPTION43.MECHANICAL SPECIFICATIONS44.INTERFACE SIGNALS65.ABSOLUTE MAXIMUM RATINGS76.ELECTRICAL SPECIFICATIONS77.OPTICAL CHARACTERISTICS88.TIMING CHARACTERISTICS109.RELIABILITY TEST ITEM1210.SUGGESTIONS FOR USING LCD MODULES1611.PACKING(REFERENCE ONLY)171. Document revision history :DOCUMENTREVISIONDATEDESCRIPTIONPREPAREDBYAPPROVEDBYA2011.07.23First Release.刘鸿杰 2. General Description3.5”(diagonal), 320 x3 RGB x 480 dots, 262k colors, Transmissive, TFT LCD module. Viewing Direction: 12 oclock. Driving IC:HX8357B 16-bits data bus (I80 system interface). Logic voltage: 2.8V (typ.). With touch panel. 3. Mechanical Specifications The mechanical detail is shown in Fig. 1 and summarized in Table 1 below.Table 1ParameterSpecificationsUnit主屏Color TFT320xRGBx480Outline dimensions55.2 (W) x83.6(H) x1.95(D)mmTP view areaNCmmTP active areaNCmmLCD active area48.96(W) x73.44(H)mmDisplay format320 x3 RGB x 480dotsColor configurationRGB stripes-Dot pitch0.153(RGB)(W) x 0.153(H)mmWeightTBDgramsFigure 1: Outline Drawing 4. Interface signalsTable 2: Pin assignment Pin No.SymbolDescription1GNDGROUND2DB0Data3DB1Data4DB2Data5DB3Data6DB4Data7DB5Data8DB6Data9DB7Data10IOVCCPOWER SUPPLY（1.8V/2.8V）11WRWRITE SIGNAL12RDREAD SIGNAL13DB9Data bus.14DB10Data bus.15DB12Data bus.16DB13Data bus.17DB15Data bus.18LEDK6POWER SUPPLY- FOR BACKLIGHT CATHODE19LEDK5POWER SUPPLY- FOR BACKLIGHT CATHODE20LEDK4POWER SUPPLY- FOR BACKLIGHT CATHODE21LEDK3POWER SUPPLY- FOR BACKLIGHT CATHODE22LEDK2POWER SUPPLY- FOR BACKLIGHT CATHODE23LEDK1POWER SUPPLY- FOR BACKLIGHT CATHODE24RESETRESET PIN25CSCHIP SELECT PIN26RSCOMMAND AND DATA REGISTER SELECT PIN27DB14Data bus.28DB11Data bus.29DB8Data bus.30VCIPOWER SUPPLY（2.8V）31FMARKTearing effect output pin to synchronies MCU to frame writing, activated by S/W command. When this pin is not activated, this pin is low. If not used, please open this pin.32GNDGROUND33YUTOUCH PANEL Y_ UP （Y+）34YDTOUCH PANEL Y_DOWN（Y-）35XRTOUCH PANEL X_ RIGHT（X+）36XLTOUCH PANEL X_ LEFT（X-）37LEDAPOWER SUPPLY+ FOR BACKLIGHT ANODE5. Absolute Maximum Ratings5.1Electrical Maximum Ratings for IC OnlyTable 3: Electrical Maximum Ratings for ICParameterSymbolMin.Max.UnitNotePower supply voltage (VCI)VCI-0.3+4.0V1Power supply voltage (IOVCC)IOVCC-0.3+3.6V1Note:1.IOVCC,VCI, GND must be maintained.2.The modules may be destroyed if they are used beyond the absolute maximum ratings.5.2Environmental ConditionTable 4ItemOperatingtemperature(Topr)Storagetemperature(Tstg) (Note 1)RemarkMin.Max.Min.Max.Ambient temperature-20C+70C-30C+80CDryHumidity (Note 1)80% max. RH for Ta 40C 50% RH for 40C Ta Maximum operating temperatureNo condensationNote 1: Product cannot sustain at extreme storage conditions for long time.6. Electrical Specifications Typical Electrical Characteristics At Ta = 25 C, VCI = 2.6V to 3.3V, IOVCC= 1.65V to 3.3V GND=0V.Table 5ParameterSymbolConditionsMin.Typ.Max.UnitSupply voltage (analog)VCI-GNDVSupply voltage (logic)IOVDD-GND1.651.83.3VSupply current (Logic & LCD)ICCVCI=2.8V-10mASupply voltage of white LED backlightVLED=V(BL+)-V(BL-)Forward current =90 mANumber of LED dies = 63.03.23.4VLuminance (on the module surface)-180-cd/m27. Optical CharacteristicsTable 7: Optical specificationsItemsSymbolConditionSpecificationsUnitNoteMin.Typ.Max.Contrast RatioCR-300-Response TimeTR-1020msTF-1520msChromaticityRedXR0.6040.6340.664-YR0.2980.3280.358-GreenXG0.2640.2940.324-YG0.5470.5770.607-BlueXB0.1070.1370.167-YB0.1040.1340.164-WhiteXW0.2720.3020.332-YW0.3050.3350.365-Viewing angleHor.f1(3 oclock)CenterCR10-45-deg.f2(9 oclock)-45-Ver.q2(12 oclock)-40-q1(6 oclock)-20-NTSC ratio61.5%Note 1: Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L63 / L0 L63: Luminance of gray level 63 L0: Luminance of gray level 0 CR = CR (10) CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note 5.Note 2: Definition of Response Time (TR, TF):Figure 3Note 3: Viewing Angle Figure 4The above “Viewing Angle” is the measuring position with Largest Contrast Ratio; not for goodimage quality. View Direction for good image quality is 6 Oclock. Module maker can increasethe “Viewing Angle” by applying Wide View Film.Note 4: Measurement Set-Up: The LCD module should be stabilized at a given temperature for 20 minutes to avoid abrupttemperature change during measuring. In order to stabilize the luminance, the measurementshould be executed after lighting Backlight for 20 minutes in a windless room. Figure 58. Timing Characteristics8.1 80-system Bus Interface Timing Characteristics of ICTable 8: Normal Write Mode (VCC = IOVCC=2.43.3V)Figure 7. 80-system Bus Timing8.2 Reset Operation of ICTable 9: Reset Timing Characteristics (VCC = IOVCC=2.43.3V)Figure 8: Reset Timing9. Reliability Test ItemTest ItemSample TypeTest ConditionTest result determinant gistHigh temperature storageNormal temperature703;96Hthe inspection ofappearance and function character.Wide temperature803;96HLow temperature storageNormal temperature-203;120HWide temperature-303;120HHigh temperature/humidity storageNormal temperature503,90%3%RH;96HWide temperature603,90%3%RH;96HHigh temperature operationNormal temperature603;96Hno objection of the function character; no fatal objection of the appearance.Wide temperature703;96HLow temperature operationNormal temperature03;96HWide temperature-203;96HHigh temperature/humidity operationNormal temperature403,90%3%RH;96HWide temperature503,90%3%RH;96HTemperature ShockNormal temperature-203,30min703,30min;10cycleinspect the objections appearance、function & the whole structureWide temperature-303,30min803,30min;10cycleThe inspection of appearance、function & the whole structure9.1 特殊检验要求：检查项目可接受标准备注背光1.无背光不接受2.亮度，均匀度及功耗须在 SPEC 之内3.颜色坐标需在规格内或依据限度4.非背光框变形的漏光在玻璃外缘可以接受目视检查/放大镜铁壳任何明显可见的损坏、变形和其它铁壳上有锡渣不可接受FPC1.变形和折痕标准如图所示，两条折痕的角度不能超过900C2.补强板裂、破损、外来材料和气泡的面积,如果超过补强板的 1/5 不能接受3.金手指部位有明显划伤、污点和外来细小指针状的异物都不可接受4.金手指氧化或者电镀不良不可以接受5. pad 脱落或者断裂不可接受9.2 TFT&触摸屏检查标准如下表:检查项目Accesseble standard备注1.线状缺陷(黑/白线等)length（mm）wide（mm）Accesseble QTY-W 0.05accessL 50.05 W 0.112.划伤length（mm）wide（mm）Accesseble QTY-W 0.05accessL 50.05 W 0.113.点状缺陷size(mm)Accesseble QTYD0.10access0.10D0.2020.20.250D= (长边直径X+短边直径 Y)/24. TP 鱼眼、凹点、气泡size(mm)Accesseble QTYD0.20access0.20D0.3060.30.505.牛顿环检查A均匀牛顿环(图 A)1.如牛顿环面积大小超过T/P 整个面积的1/4，则不可接受.2.在莹光灯下，如牛顿环小于 T/P 的 1/4 且不影响显示字体效果，则可接受B不均匀牛顿环(图 B)1.在无莹光灯下，如牛顿环大于 7mm，则不可接受2. 在莹光灯下，无论大小只要造成文字失真或直线变形，判定 NG备注：檢驗時要撕起保護膜，检查规格参照点状、線状异物混入判定標准。以上的点缺陷距离必须大于 5mm &点、线缺陷相加后可接受数量之总和为 5代号说明：X:崩裂长度 Y：崩裂宽度 Z：崩裂厚度 a:LCD 边长 D:端子长度 t:玻璃厚度6.表面及中间崩ZXYZ1/2tXa不可以进入 SP 内缘Z1/2tXa需要保留 1/2 SP 宽度7.角崩ZXYZ1/2tX1/8a不可以进入 SP 内缘Z1/2tX1/8a需要保留 1/2 SP 宽度8 电极端子区崩XYZ正面X1/5aY0.5mmzt背面X1/5aY0.5mmz1/2t以上崩裂超过一处时间，X 是所有崩裂长度的总和；正面的崩裂不可以进入视区。每一单处电极的崩裂宽度不超过原电极宽度的 1/49.裂任何有延伸趋势的裂痕都不可接受偏光片、反射片与玻璃不良玻璃、反射片与偏光片的破损及划伤遵照点状缺陷和线状缺陷标准Minor不应有贴反、未贴、贴错等现象Minor尺寸应符合规范,不应无保护膜贴歪的偏光片应该显现全部的 SP 框形有效可视面不良（电测）缺行、缺列、串扰、乱码不可以接受Major色度、灰度、亮度、均匀度和对比度失常（对比 Golden Sample 和 Spec.）不显示的像素中异常点/线（工艺形成）遵照点状缺陷和线状缺陷标准显示偏、斜（S）遵照下表：S0.3mm可接受0.3mmS=3个相邻的点0 10. Suggestions for using LCD modules 10.1 Handling of LCM1. The LCD screen is made of glass. Dont give excessive external shock, or drop from a high place.2. If the LCD screen is damaged and the liquid crystal leaks out, do not lick and swallow. When the liquid is attach to your hand, skin, cloth etc, wash it off by using soap and water thoroughly and immediately.3. Dont apply excessive force on the surface of the LCM.4. If the surface is contaminated ,clean it with soft cloth. If the LCM is severely contaminated , use Isopropyl alcohol/Ethyl alcohol to clean. Other solvents may damage the polarizer . The following solvents is especially prohibited: water , ketone Aromatic solvents etc.5. Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated by water droplets, moisture condensation or a current flow in a high-humidity environment.6. Install the LCD Module by using the mounting holes. When mounting the LCD module make sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I/O cable or the backlight cable.7. Dont disassemble the LCM.8. To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment.- Be sure to ground the body when handling the LCD modules.- Tools required for assembling, such as soldering irons, must be properly grounded.- To reduce the amount of static electricity generated, do not conduct assembling and other work under dry conditions.- The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this protective film since static electricity may be generated.9. Do not alter, modify or change the the shape of the tab on the met