MPLAB ICD 2 USB Device Driver 的安装.doc

MPLAB IDE MPLAB ICD 2 USB Device Driver First Time Installation For Windows 2000 and XP 32 OSsTo use MPLAB ICD 2 with USB communications, the following steps MUST be taken in order to properly install the device drivers.Before You Begin Determine your method of communication between the ICD and the PC.1. Serial port communication - No driver installation is needed. Plug in the serial cable and set up communications in MPLAB IDE.2. USB communication - Follow the instructions listed here. If you have already preinstalled the drivers during MPLAB IDE installation, read USB Preliminaries and then jump to Step 4. Otherwise follow all instructions.Note 1: Do not plug in both serial and USB cables. Choose one method of communication and use that cable only.Note 2: For Windows XP 64, please see the Readme file for device driver installation instructions.USB Preliminaries MPLAB ICD 2 should NOT be plugged into a USB port, powered, or plugged into a target board at this time. If you have already plugged MPLAB ICD 2 into the USB port and the Found New Hardware Wizard has popped up, click Cancel on that dialog, unplug the MPLAB ICD 2 and continue with these instructions.If you have already plugged MPLAB ICD 2 into the USB port and used the Found New Hardware Wizard to install drivers automatically, you have installed the wrong drivers. Follow the instructions specified in C:Program FilesMicrochipMPLAB IDEUtilitiesMPUsbCleanMPUsbDocsUpdate_Clean.htm.Software Preliminaries During the install, a dialog may pop up twice stating, The software you are installing for this hardware: Microchip Development Tool has not passed Windows Logo testing. In this case, Microchip Development Tool will be: Microchip MPLAB ICD 2 Firmware LoaderMicrochip MPLAB ICD 2 Firmware ClientIf this happens, click Continue Anyway each time. STEP 1 Connect MPLAB ICD 2 to the PC with a USB cable. If you are planning on using both USB and an external power supply, use only USB when installing the drivers, i.e., DO NOT plug an external power supply into the pod for driver installation.If you are using an external USB HUB, make sure it has a power supply and is powered or MPLAB ICD 2 will not work.STEP 2 - Windows XP SP2 If you have service pack 2, the first time a new USB device is plugged into a Windows XP system, this dialog box will appear indicating that the system has found a new hardware device and asking you whether or not to search for update software. Select No, not this time. Click Next and continue with the steps below.STEP 3 The first time a new USB device is plugged in, a small dialog box will appear indicating that the system has found a new hardware device. There also may be a dialog box that informs the user that a device data base is being built or updated. After these dialogs appear, the Found New Hardware Wizard dialog box is displayed. Select Install the software automatically (Recommended) and click Next to continue the installation. Note: If you are running Windows 2000, you may not see this dialog or the next 3 dialogs. Instead, the system will automatically install the software without asking you. This is OK. Proceed to Step 7.STEP 4 During the install, a dialog will pop up stating, The software you are installing for this hardware: Microchip Development Tool has not passed Windows Logo testing. In this case, Microchip Development Tool will be Microchip MPLAB ICD 2 Firmware Loader. Click Continue Anyway. (See “Software Preliminaries” for a picture of this dialog.) The Completing the Found New Hardware Wizard will appear once the Microchip MPLAB ICD 2 Firmware Loader has been installed. Click Finish to end this installation and begin the install of the Firmware Client.STEP 5 A small dialog box will appear indicating that the system completed adding a hardware device, immediately followed by the statement that it has found a new hardware device. After this dialog appears, the Found New Hardware Wizard dialog box is displayed again, this time to install the Microchip MPLAB ICD 2 Firmware Client. Select Install the software automatically (Recommended) and click Next to continue the installation.STEP 6 During the install, a dialog will pop up stating, The software you are installing for this hardware: Microchip Development Tool has not passed Windows Logo testing. In this case, Microchip Development Tool will be Microchip MPLAB ICD 2 Firmware Client. Click Continue Anyway. (See Step 3 for a picture of this dialog.) The Completing the Found New Hardware Wizard will appear once the Microchip MPLAB ICD 2 Firmware Client has been installed. Click Finish to end the USB installation.STEP 7 Verify that the driver installed by viewing the Device Manager*, Microchip Tools section.Complete the installation by referring to the Using MPLAB ICD 2 (DS51265), MP