关 键 词：

机械类毕业论文中英文对照文献翻译 机械类 毕业论文 中英文 对照 文献 翻译 减速器 差速器 调整 装配

资源描述：

【机械类毕业论文中英文对照文献翻译】减速器和差速器的调整与装配,机械类毕业论文中英文对照文献翻译,机械类,毕业论文,中英文,对照,文献,翻译,减速器,差速器,调整,装配

内容简介：

黑龙江工程学院本科生毕业设计附 录 A 外文文献Farm Machinery Using & MaintenanceThe most important thing is the meshing mark and meshing backlash of the driven bevel gears and active bevel gears, the firmness adjustment of half axle gears and planetary gear in maintenance of the BJ2020S jeep driving axle . This is an important and difficult job ,because the rear axle and driven working under the large load and high speed. And the bear is alternating load. If the meshing mark is not conforming to requirements or the meshing backlash is not good, it will appear smooth transmission speed and noise, wear, or even broken tooth gear, which directly influences the car service life and various tasks when it is working. At the same time , lord and driven tapered gear meshing mark and the check assembly and adjustment became a complicated problem although automobile driving axle structure is not a very complicated but some people is not familiar with the principle on gear transmission. Based on years of teaching and practice in the maintenance work with the adjustment of BJ2020S jeep driving axle differential gears and bearings has some method and steps of the relevant views and comments about something. Adjustment of the axis gear differential planetary gear mesh clearanceHalf axle gears and planetary gear mesh clearance is adjusted by half axle gears and differential shell thickness between three different (0.5 mm, 1.0 mm, 0.2 mm) thrust washers . Because of the planetary gear differential between shell with the thrust washers, so it must be the half axle gears through the thrust washers (two half axle gears and add, subtract washers), and the gap of the planetary gear mesh. Then using pins will planetary gear axle fixed. Adjustment of differential backlash This bearing clearance is adjusted by adding, subtracting differential bearings and differential between shell thickness (0.5 mm in four different, o. mm, 0.15 ram, 0.10 ram) to adjust the adjustment of the gasket. In the adjustment of the former ready right and left bridge between shell of gasket, installation fixed good follower bevel gears. Active bevel gears should not installed in accordance with the relevant provisions of the torque (40-60N, m) installed left and right with tapered bridge housing, active gear with long bar, or a screwdriver to turn down, or pry differential assembly, to check differential assembly bearings between differential to feel no axial clearance and rotate freely. Active bevel gears bearing clearance adjustment In active position of bevel gears can be determined by the basic, increase and decrease active bevel gears with active before bearings taper gear bearing thrust ring between four different thickness (0.10 mm, 0.15 ram, 0.25 mm mm) adjustment, 0.50 gasket to adjust, the flexible rotation, no axial and radial clearance. Active bevel gears and driven bevel gears clearance and meshing mark adjustment Domestic automobile gear for no modifier, assembling widely adopted, the first meshing mark check whether the meshing mark requirements, such as requirements, through the change of bevel gears, driven axial position to get to meet the requirements of meshing mark, the active bevel gears bearing and differential bearing clearance (pre-tightening degrees) basis, rub-up, driven bevel gears, initiative on 3-4 taper gear teeth are coated with thin layer opposite, oil (or face turns into oil), according to the requirements and differential assembly installed left, right, forward and backward bridge housing, then turn active bevel gears decomposition of left and right to bridge housing, driven gear tooth surface of conical whether imprint requirements. If meshing mark requirements, visible to the situation by outward, to the right or left, bevel gears, driven to adjust. When the meshing mark to tooth root cap, the main, small or client, the formula for the Lord: the Lord, from (i.e., big into bevel gears into active driven gear), small (i.e. driven out from bevel gears removed from active gear). When the Lord, driven gear cone of meshing mark complies with the standards and inspection, driven bevel gears, active bevel gears and clearance of bevel gears driven backlash should actively bevel gears in the radius of 45mm flanges on the circumference displacement measurement, the arc length) should be in (0.2-0.6 mm. If does not accord with a standard, can increase and decrease active bevel gears and bearings taper gear after the shim between left and right or mobile differential bearing adjustment gasket, driven to adjust the gap, so bevel gears, driven when the bevel gears has adjusted, adjust the marks are not destroyed, small volume, driven tapered gear meshing mark. Drive and differential assemblyWe can start assemble the drive and differential when the differential gears, driven gear, each bearing, tapered meshing mark adjustment is over. Based on the thickness of the gasket and the bolt torques, we should coated with rubber seal, assembled active bevel gears, mount differential assembly, then closed the bridge housing.附 录 B 中文译文减速器和差速器的调整与装配在对BJ2020S吉普车后桥的维修中，最主要的就是减速器主、从动圆锥齿轮的啮合印痕及啮合间隙；差速器半轴齿轮、行星齿轮啮合间隙和各轴承松紧度的调整。这是一项既重要又较为困难的工作，因为后桥主、从动圆锥齿轮是在大负荷、高转速下工作的，而且其所承受的是交变负荷，如果两者的啮合印痕不符合要求，或啮合间隙不当，工作中将会出现传动不平稳和噪音，加速齿面磨损，甚至打坏齿轮，直接影响汽车使用寿命和各项任务的完成。同时，汽车后桥的结构虽不是很复杂，但由于主、从动圆锥齿轮的体积较大，拆装费时费力，加之一些同志对齿轮的传动原理不够熟悉，实践机会又少，主、从动圆锥齿轮啮合印痕和间隙的检查调整及装配就成了一个较为复杂的问题。本文根据几年来在教学和实际维修工作中的摸索，就BJ2020S吉普车后桥差速器齿轮和轴承的调整，主、从动圆锥齿轮啮合印痕和间隙及主动圆锥齿轮轴承间隙的调整和装配的有关方法、步骤谈点看法和意见。一、差速器半轴齿轮与行星齿轮啮合间隙的调整 半轴齿轮与行星齿轮啮合间隙的调整，是通过半轴齿轮与差速器壳之间三个不同厚度(1.0mm、0.5mm、0.2mm)的止推垫片来调整的。因为行星齿轮与差速器壳之间的止推垫片是一定的，所以，通过加、减半轴齿轮的止推垫片(两半轴齿轮同时加、减垫片)，使其与行星齿轮的啮合间隙达到标准。然后用销子将行星齿轮轴固定。二、差速器轴承间隙的调整 此轴承间隙的调整是通过加、减差速器轴承与差速器壳之间四个不同厚度(0.5mm、0.25mm、0.15ram、0.10ram)的调整垫片来调整的。在调整前准备好左、右桥壳之间的密封垫，安装固定好从动圆锥齿轮。主动圆锥齿轮先不要安装，应按照规定的扭矩(4060Nm)安装好左、右桥壳，以圆锥主动齿轮的位置，用长金属棒或大起子转动差速器总成，或上下撬差速器总成，来检查差速器轴承间隙，以达到感觉没有轴向间隙且转动自由为止。三、主动圆锥齿轮轴承间隙的调整 在主动圆锥齿轮的位置基本确定后，可通过增、减主动圆锥齿轮前轴承与主动圆锥齿轮前轴承止推环之间的四个不同厚度(0.10mm、0.15ram、0.25mm、0.50mm)的调整垫片来调整，使其达到转动灵活，没有轴向、径向间隙的感觉。四、主动圆锥齿轮与从动圆锥齿轮间隙及啮合印痕的调整 国产