【机械类毕业论文中英文对照文献翻译】钢坯火焰清理机氧化皮、裂纹清理【word英文1265字6页word中文翻译1899字4页】
收藏
资源目录
压缩包内文档预览：
编号：77694032
类型：共享资源
大小：31.01KB
格式：RAR
上传时间：2020-05-07
上传人：柒哥
认证信息
个人认证
杨**（实名认证）
湖南
IP属地：湖南
6
积分
- 关 键 词：
-
机械类毕业论文中英文对照文献翻译
word英文1265字6页，word中文翻译1899字4页
机械类
毕业论文
中英文
对照
文献
翻译
钢坯
火焰
清理
氧化
裂纹
word
英文
1265
中文翻译
- 资源描述：
-
【机械类毕业论文中英文对照文献翻译】钢坯火焰清理机氧化皮、裂纹清理【word英文1265字6页word中文翻译1899字4页】,机械类毕业论文中英文对照文献翻译,word英文1265字6页,word中文翻译1899字4页,机械类,毕业论文,中英文,对照,文献,翻译,钢坯,火焰,清理,氧化,裂纹,word,英文,1265,中文翻译
- 内容简介：
-
附录2：英文技术资料及中文翻译Billet flame cleaning machine oxide skin, crack cleaning device design From steel plate through a series of intermediate link reach incision workshop, during this period, the steel plate surface unavoidably produce a layer of oxide skin. Moreover, steel rolling process also produce in a layer of oxide skin attached to the steel plate surface. These oxide skin melting point, not easy high combustion and melting, increased preheating time, reduced the cutting speed; Meanwhile, after heating, oxide skin around the splash and extremely easily to cut caused jams, reduces the lips mouth using life. Cut So, in is necessary before cutting for steel surface derusting pretreatment. Commonly used method is peen-forming derusting, after painting antirust. Upcoming shot peening machine with tiny iron ore, steel surfaces by soar into the impact of the of the steel iron ore remove oxide skin, spray flame retardant and electric conductivity good antirust paint. Steel cutting the derusting spray-paint preprocessing before production of metal structure has become an indispensable tache. In the actual production process, often have this or that kind of quality problem, generally has the following several defects: edge defects, cutting section defects, hang slag, crack, etc. The causes of the accident caused by quality, if oxygen purity guarantee many normal, in normal operation, then the flame cutting quality defects caused by reason mainly lie in the following aspects: cutting torch, cut the mouth, steel, steel material quality of itself. 1. The upper edge cutting quality defects This is because the quality defect caused by the melting. (1) on edge collapse edge Phenomenon: melting too fast, causing rounded edge collapse edge. Reason: (1) the cutting speed too slow, preheat flame strong; (2) the mouth and workpiece cut between highly too much or too little; The use of mouth number too big, cut the oxygen excess. Flame (2) water droplets shape molten bean string (see chart 9-9) Phenomenon: in cutting the upper edge of the form a string of water droplets form of melting beans. Reason: (1) the steel plate surface corrosion or have oxide skin; (2) the steel mouth and cut between too high too small, preheat flame; (3) the steel mouth and cut between highly too big. (3) the upper edge of the present FangYan shape and collapse edge (see chart 9-10) Phenomenon: in the upper edge of the FangYan incision, forming the bulge (collapse edge. Reason: (1) the preheating flame strong; (2) the steel mouth and cut between highly too low; (3) cutting speed too slow; Cut the height of mouth and between parts, the use of cut too large, too large, the mouth overcapacity. Oxygen in the preheated flame (4) cutting section has hang the upper edge of the slag (see chart 9-11) Phenomenon: cut on the edge sag and hangs slag. Reason: (1) the mouth and workpiece cut between highly too big, cut oxygen pressure is too high; (2) the preheating flame is too strong. 2. Cutting section is uneven, namely flatness poor (1) cutting edge on the cross, has sunken shape defects below (see chart 9-12) phenomenon: in accepting the edge cutting sections have cave, meanwhile the upper edge of the different levels of melting collapse edge. Reason: (1) cut oxygen pressure is too high; (2) the mouth and workpiece cut between highly too big; Cut the mouth had sundry jams, make the wind line interference deformation. (2) cut from top down contraction joints (see chart 9-13) Phenomenon: cut to sew up wide below narrow. Reason: (1) cut too fast; (2) the mouth and workpiece cut between highly too big, cut the mouth had sundry jams, make the wind line interference deformation. (3) cut to sew up the narrow below wide (see chart 9-14) Phenomenon: cut with narrow width, sewn into horn shape. Reason: (1) the cutting speed too fast, cutting oxygen pressure is too high; (2), cut too large, the mouth that cutting oxygen flow too big; (3) the mouth and workpiece cut between highly too big; (4) cutting section sag (see chart 9-15) Phenomenon: in the whole cutting section, especially have sunken intermediate place. Reason: (1) cut too fast; (2) the use of mouth is too small, cutting pressure cut is too low, cut congestion or damage; mouth (3) cutting too high, the wind line oxygen pressure thwarted worse. (5) cutting sections show big corrugated shape (see chart 9-16) Phenomenon: cutting section bumpy, appear larger corrugated shape. Reason: (1) cut too fast; (2) the cutting oxygen pressure is too low, the mouth jam or damage, cut to the wind line deteriorate; (3) the mouth, use cut is too big. (6) incision of perpendicular direction Angle deviation (see chart 9-17) Phenomenon: incision not vertical, appear bevel. Reason: (1) the torch with workpiece surface will not cut vertical; (2) the wind line is not right. (7) incision into round the lower edge (see chart 9-18) Phenomenon: incision had different degrees of the lower edge of the melt into round shape. Reason: (1) mouth jam or damage, cut to the wind line deteriorate; (2) the cutting speed too fast, cutting oxygen pressure is too high. (8) incision under the lower sag and into rounded edge (see chart 9-19) Phenomenon: close to lower edge sag under melting into fillet and edge. Reason: Cutting too fast, mouth jam or damage, cut the line go bad. Blocked 3. Cutting sections of roughness defects of cutting section directly influences the follow-up process roughness machining quality, the roughness and cut off the depth and volume of advanced tattoo concerned. (1) after cutting section dragged dimension (FIG 9-20) Phenomenon: cutting section cut grain backward migration is very big, at the same time as the size of the offset and appear different levels of depression. Reason: (1) cut too fast; (2) the use of cut is too small, and cutting oxygen flow mouth too low, cutting oxygen pressure; (3) the height of mouth and workpiece cut is too big. (2) in the first half part, cutting sections appear cut lines leading quantity (see chart 9-21) Phenomenon: the edge in close, forming a certain degree of cut lines leading quantity. Reason: (1) the torch and cutting direction not cut, cut congestion or vertical mouth damage; (2) the wind line thwarted deteriorate; Phenomenon: near the lower edge cutting sections appear cut lines leading quantity too big. Reason: (1) mouth jam or damage, cut thwarted deteriorate; the wind line (2) the torch not cut vertically or cut mouth has a problem, make the wind line corruptive, tilt. 4. Hang slag in the lower edge cutting sections or to remove produced hang slag. (1) the lower edge of the hanging slag (see chart 9-23) Phenomenon: in the bottom edge cutting section produced continuous hang slag. Reason: (1) too fast or slow cutting, the use of cut, too small, cutt
- 温馨提示:
1: 本站所有资源如无特殊说明，都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等，如果需要附件，请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸，网页内容里面会有图纸预览，若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 人人文库网仅提供信息存储空间，仅对用户上传内容的表现方式做保护处理，对用户上传分享的文档内容本身不做任何修改或编辑，并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容，请与我们联系，我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
人人文库网所有资源均是用户自行上传分享，仅供网友学习交流，未经上传用户书面授权，请勿作他用。
川公网安备: 51019002004831号