51单片机数码管显示温度程序

/项目：数码管温度显示器/编写：LGY/功能：数码管显示温度#includereg52.h#includeintrins.h#define uchar unsigned char#define uint unsigned int/*位定义*/sbit RX =P30;sbit TX =P31;sbit RX_TX_con =P32;/sbit Fre_check =P35;sbit DQ =P35;sbit SDA =P36;sbit SCL =P37;sbit LED_1 =P02;sbit LED_2 =P00;sbit LED_3 =P01;sbit LED_4 =P03;unsigned char a1,a2,a3,a4;unsigned int temper;unsigned char code displaycode= / 0 1 2 3 4 5 6 7 8 9 0x28, 0xee, 0x32, 0xa2, 0xe4, 0xa1, 0x21, 0xea, 0x20, 0xa0, ;unsigned char code displaycode1= / 0. 1. 2. 3. 4. 5. 6. 7. 8. 9. 0x08, 0xce, 0x12, 0x82, 0xc4, 0x81, 0x01, 0xca, 0x00, 0x80, ;void INT() P0=0xff; P1=0xff; P2=0; P3=0; DQ=1; / Fre_check=1; void Delay(uint x) uint a,b; for(a=x;a0;a-) for(b=110;b0;b-);/*void Delay1(uint x,uchar y)uint i;uchar j;for(i=x;i0;i-);for(j=y;j0;j-);void reset()unsigned char st=1;Fre_check=1;/_nop_();/_nop_();while(st)Fre_check=0;Delay1(70,30);Fre_check=1;Delay1(4,4);if(Fre_check=1) st=1;else st=0;Delay1(50,10);void write_byte(unsigned char date)unsigned char temp,i;Fre_check=1;/_nop_();/_nop_();for(i=8;i0;i-) temp=date&0x01;Fre_check=0; /Delay1(1);_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();if(temp=1) Fre_check=1;Delay1(2,2);Fre_check=1;date=date1;unsigned char read_byte()unsigned char i,date;static bit j;for(i=8;i0;i-)date=date1;Fre_check=1;_nop_();_nop_();Fre_check=0;_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();Fre_check=1;_nop_();_nop_();_nop_();_nop_();j=Fre_check;if(j=1) date=date|0x08;Delay1(1,1);return (date);*/void delay1(int b)int s;for (s = 0; s b; s+);unsigned char ow_reset(void)unsigned char presence;DQ = 0; /pull DQ line lowdelay1(29); / leave it low for 480sDQ = 1; / allow line to return highdelay1(3); / wait for presencepresence = DQ; / get presence signaldelay1(25); / wait for end of timeslotreturn(presence); / presence signal returned / presence = 0, no part = 1unsigned char read_bit(void)unsigned char i;DQ = 0; / pull DQ low to start timeslotDQ = 1; / then return highfor (i = 0; i 3; i+); / delay 15s fromstart of timeslotreturn(DQ); / return value of DQ linevoid write_bit(char bitval)DQ = 0; / pull DQ low to start timeslotif(bitval=1) DQ =1; / return DQ high if write 1delay1(5);/ hold value for remainder of timeslotDQ = 1;/ Delay provides 16s per loop, plus 24s/Therefore, delay(5) = 104sunsigned char read_byte(void)unsigned char i;unsigned char value = 0;for (i = 0; i 8; i+)if(read_bit() value=value|0x01i;/ reads byte in, one byte at a time and then/ shifts it leftdelay1(6); / wait for rest of timeslot return(value);void write_byte(char val)unsigned char i;unsigned char temp;for (i = 0; i i; / shifts val right i spacestemp &= 0x01; / copy that bit to tempwrite_bit(temp); / write bit in temp intodelay1(5);void DisplayLed(uchar num1,uchar num2,uchar num3,uchar num4) LED_1=0;LED_2=1;LED_3=1;LED_4=1;P1=displaycodenum1;Delay(3); LED_1=1;LED_2=0;LED_3=1;LED_4=1;P1=displaycode1num2;Delay(3); LED_1=1;LED_2=1;LED_3=0;LED_4=1;P1=displaycodenum3;Delay(3); LED_1=1;LED_2=1;LED_3=1;LED_4=0;P1=displaycodenum4;Delay(3);void Get_tem()unsigned char tem1,tem2,num;float aaa;int temper;ow_reset(); /复位write_byte(0xCC);/跳过ROMwrite_byte(0x44);/温度转换for(num=1000;num0;num-) DisplayLed(a1,a2,a3,a4);ow_reset();write_byte(0xCC);write_byte(0xBE);tem1=read_byte();tem2=