Development of an automated testing system.pdf
559 大学生方程式赛车设计（传动及最终传动系统设计）（有cad图+三维图+翻译）
收藏
资源目录
压缩包内文档预览：
编号：834247
类型：共享资源
大小：9.44MB
格式：RAR
上传时间：2016-10-10
上传人：hon****an
认证信息
个人认证
丁**（实名认证）
江苏
IP属地：江苏
30
积分
- 关 键 词：
-
大学生
方程式赛车
设计
传动
最终
终究
传动系统
cad
三维
翻译
- 资源描述：
-
大学生方程式赛车设计（传动及最终传动系统设计）
摘 要
汽车传动系统的基本功用是将发动机输出的动力传递给驱动车轮，传动系统对整车的动力性和设计中一个重要的组成部分。本文主要研究的是FSAE方程式赛车传动系统的燃油经济性有很大的影响，故传动系统参数的确定是汽车设计，基于我院LS Racing车队三年来的比赛经验和设计理念，对赛车的传动系统进行优化和改造。本赛车选用的是铃木CBRR600四缸发动机，差速器是选用德雷克斯勒限滑差速器（Drexler），根据发动机的特性参数、档位比和差速器的工作原理，选择合适的链传动比，计算链条的参数，设计差速器固定支架，合理的布置整个传动系统。针对传动系统各组成部件，采用ANSYS有限元分析软件对零部件进行强度校核，优化结构使其达到质量轻、强度高的目标。
关键字：FSAE，差速器选型，德雷克斯勒限滑差速器，传动系
- 内容简介：
-
of an R. 18 009 /12 010 /15 010# 010 is of as an of at an is by an at a to s it by an a of of a of of of is a of a of to a as D to as a in by in to of in in In a is as a In is in a to as 1. OS as in an it be in be of *):R. . . P. . . 2010) 51:233246is of is by at a to is to do by is in of is to is an a to of be to a of or in of a of as of a UK of a by a in to of in of a to of of of by an In to a is to of It is an , in on To is to A to a be of of IL 25of 6, 7. of to of in as 810, 11, 12, 13. in 4, 15. no in is in a a to to is in is it a of to of of of of is of IL In a to as in to of by a is by In to be in by IL of as of is 1. of of a D SB,MI is on a 7 on 2010) 51:233246in on is a is is to of a CM as a It is CP on in In a by IL to of a IL to It as to it a to of of as of is a is in IL By to of up is is in to to a In C a P of C so of in of of IL IL 16 to a IL AN to to CP to te s t te s t te s t te s t te s tto of 1 2010) 51:233246 235In IL S 232 to to ,A/S 232to IL s of of of by a of To of to be in In a by CU to we on a a in we of IL to CU to CP of a of by CP of Ds,up/D so To an of CP be by CP a CP AN of CP or of is 1, by A/D 2 2010) 51:233of is to IL so be IL is to to to to a to be to a of in a to be to so be of of is is a a 0 A is 3 CP 2010) 51:233246 2374 of a A 17 a 40480 a 32of 0 is ) of 17 of is a on of In a a be in to to by in be
- 温馨提示:
1: 本站所有资源如无特殊说明，都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等，如果需要附件，请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸，网页内容里面会有图纸预览，若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 人人文库网仅提供信息存储空间，仅对用户上传内容的表现方式做保护处理，对用户上传分享的文档内容本身不做任何修改或编辑，并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容，请与我们联系，我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
人人文库网所有资源均是用户自行上传分享，仅供网友学习交流，未经上传用户书面授权，请勿作他用。
|
2:不支持迅雷下载,请使用浏览器下载
3:不支持QQ浏览器下载,请用其他浏览器
4:下载后的文档和图纸-无水印
5:文档经过压缩，下载后原文更清晰
|
川公网安备: 51019002004831号