拓迪电子-阻-容-三极管-二极管-12 6ML79L00

1/15February 2003 IOUTPUT CURRENT UP TO 100 mA IOUTPUT VOLTAGES OF -5; -6; -8; -9; -12; -15 V ITHERMAL OVERLOAD PROTECTION ISHORT CIRCUIT PROTECTION INO EXTERNAL COMPONENTS ARE REQUIRED IAVAILABLE IN EITHER 5% (AC) OR 10% (C) SELECTION DESCRIPTION The L79L00 series of three-terminalpositive regulators employ internal current limiting and thermalshutdown,makingthemessentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 mA output current. They are intended as fixed voltage regulators in a wide range of applications including local or on-card regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with powerpasselementstomakehigh-current voltage regulators. The L79L00 series used as Zener diode/resistor combinationreplacement,offersaneffective output impedance improvement of typically two orders of magnitude, along with lower quiescent current and lower noise. L79L00 SERIES NEGATIVE VOLTAGE REGULATORS SCHEMATIC DIAGRAM SO-8SOT-89 TO-92 L79L00 SERIES 2/15 ABSOLUTE MAXIMUM RATINGS (*) Our SO-8 package used for Voltage Regulators is modified internally to have pins 2, 3, 6 and 7 electrically communed to the die attach flag. This particular frame decreases the total thermal resistance of the package and increases its ability to dissipate power when an appro- priate area of copper on the printed circuit board is available for heat-sinking. The external dimensions are the same as for the standard SO-8. THERMAL DATA (*) Considering 6 cm2of copper Board heat-sink. CONNECTION DIAGRAM (top view) SymbolParameterValueUnit VI DC Input VoltageVO= -5 to -9 V -30 V VO= -12 to -15 V-35 IOOutput Current100mA PtotPower Dissipation Internally Limited (*) TstgStorage Temperature Range -40 to 150C TopOperating Junction Temperature RangeFor L79L00C, L79L00AC0 to 125C For L79L00AB-40 to 125C SymbolParameterSO-8TO-92SOT-89Unit Rthj-caseThermal Resistance Junction-caseMax 2015C/W Rthj-ambThermal Resistance Junction-ambientMax 55 (*)200C/W SO-8 TO-92 PIN 1 = VOUT PIN 2 = GND PIN 3 = VIN SOT-89 BOTTOM VIEW L79L00 SERIES 3/15 ORDERING CODES TEST CIRCUITS TYPESO-8TO-92SOT-89OUTPUT VOLTAGE L79L05CL79L05CDL79L05CZ-5 V L79L05ACL79L05ACDL79L05ACZL79L05ACU-5 V L79L05ABL79L05ABDL79L05ABZL79L05ABU-5 V L79L06CL79L06CDL79L06CZ-6 V L79L06ACL79L06ACDL79L06ACZL79L06ACU-6 V L79L06ABL79L06ABDL79L06ABZL79L06ABU-6 V L79L08CL79L08CDL79L08CZ-8 V L79L08ACL79L08ACDL79L08ACZL79L08ACU-8 V L79L08ABL79L08ABDL79L08ABZL79L08ABU-8 V L79L09CL79L09CDL79L09CZ-9 V L79L09ACL79L09ACDL79L09ACZL79L09ACU-9 V L79L09ABL79L09ABDL79L09ABZL79L09ABU-9 V L79L12CL79L12CDL79L12CZ-12 V L79L12ACL79L12ACDL79L12ACZL79L12ACU-12 V L79L12ABL79L12ABDL79L12ABZL79L12ABU-12 V L79L15CL79L15CDL79L15CZ-15 V L79L15ACL79L15ACDL79L15ACZ-15 V L79L15ABL79L15ABDL79L15ABZ-15 V L79L00 SERIES 4/15 ELECTRICAL CHARACTERISTICS OF L79L05 (refer to the test circuits, TJ= 0 to 125C, VI= -10V, IO= 40 mA, CI= 0.33 F, CO= 0.1 F unless otherwise specified). ELECTRICAL CHARACTERISTICS OF L79L06 (refer to the test circuits, TJ= 0 to 125C, VI= -12V, IO= 40 mA, CI= 0.33 F, CO= 0.1 F unless otherwise specified). SymbolParameterTest ConditionsMin.Typ.Max.Unit VOOutput VoltageTJ= 25C-4.6-5-5.4V VOOutput VoltageIO= 1 to 40 mAVI= -7 to -20 V-4.5-5.5V IO= 1 to 70 mAVI= -10 V-4.5-5.5 VOLine RegulationVI= -7 to -20 VTJ= 25C200mV VI= -8 to -20 VTJ= 25C150 VOLoad RegulationIO= 1 to 100 mATJ= 25C60mV IO= 1 to 40 mATJ= 25C30 IdQuiescent CurrentTJ= 25C6mA TJ= 125C5.5 IdQuiescent Current ChangeIO= 1 to 40 mA0.2mA VI= -8 to -20 V1.5 eNOutput Noise VoltageB = 10Hz to 100KHzTJ= 25C40V SVRSupply Voltage RejectionIO= 40 mAf = 120HzTJ= 25C VI= -8 to -18 V 4049dB VdDropout Voltage1.7V SymbolParameterTest ConditionsMin.Typ.Max.Unit VOOutput VoltageTJ= 25C-5.52-6-6.48V VOOutput VoltageIO= 1 to 40 mAVI= -8.5 to -20 V-5.4-6.6V IO= 1 to 70 mAVI= -12 V-5.4-6.6 VOLine RegulationVI= -8.5 to -20 VTJ= 25C200mV VI= -9 to -20 VTJ= 25C150 VOLoad RegulationIO= 1 to 100 mATJ= 25C60mV IO= 1 to 40 mATJ= 25C30 IdQuiescent CurrentTJ= 25C6mA TJ= 125C5.5 IdQuiescent Current ChangeIO= 1 to 40 mA0.2mA VI= -8 to -20 V1.5 eNOutput Noise VoltageB = 10Hz to 100KHzTJ= 25C50V SVRSupply Voltage RejectionIO= 40 mAf = 120HzTJ= 25C VI= -9 to -20 V 3846dB VdDropout Voltage1.7V L79L00 SERIES 5/15 ELECTRICAL CHARACTERISTICS OF L79L08 (refer to the test circuits, TJ= 0 to 125C, VI= -14V, IO= 40 mA, CI= 0.33 F, CO= 0.1 F unless otherwise specified). ELECTRICAL CHARACTERISTICS OF L79L09 (refer to the test circuits, TJ= 0 to 125C, VI= -15V, IO= 40 mA, CI= 0.33 F, CO= 0.1 F unless otherwise specified). SymbolParameterTest ConditionsMin.Typ.Max.Unit VOOutput VoltageTJ= 25C-7.36-8-8.64V VOOutput VoltageIO= 1 to 40 mAVI= -10.5 to -23 V-7.2-8.8V IO= 1 to 70 mAVI= -14 V-7.2-8.8 VOLine RegulationVI= -10.5 to -23 VTJ= 25C200mV VI= -11 to -23 VTJ= 25C150 VOLoad RegulationIO= 1 to 100 mATJ= 25C80mV IO= 1 to 40 mATJ= 25C40 IdQuiescent CurrentTJ= 25C6mA TJ= 125C5.5 IdQuiescent Current ChangeIO= 1 to 40 mA0.2mA VI= -11 to -23 V1.5 eNOutput Noise VoltageB = 10Hz to 100KHzTJ= 25C60V SVRSupply Voltage RejectionIO= 40 mAf = 120HzTJ= 25C VI= -12 to -23 V 3645dB VdDropout Voltage1.7V SymbolParameterTest ConditionsMin.Typ.Max.Unit VOOutput VoltageTJ= 25C-8.28-9-9.72V VOOutput VoltageIO= 1 to 40 mAVI= -11.5 to -23 V-8.1-9.9V IO= 1 to 70 mAVI= -15 V-8.1-9.9 VOLine RegulationVI= -11.5 to -23 VTJ= 25C250mV VI= -12 to -23 VTJ= 25C200 VOLoad RegulationIO= 1 to 100 mATJ= 25C80mV IO= 1 to 40 mATJ= 25C40 IdQuiescent CurrentTJ= 25C6mA TJ= 125C5.5 IdQuiescent Current ChangeIO= 1 to 40 mA0.2mA VI= -12 to -23 V1.5 eNOutput Noise VoltageB = 10Hz to 100KHzTJ= 25C70V SVRSupply Voltage RejectionIO= 40 mAf = 120HzTJ= 25C VI= -12 to -23 V 3644dB VdDropout Voltage1.7V L79L00 SERIES 6/15 ELECTRICAL CHARACTERISTICS OF L79L12 (refer to the test circuits, TJ= 0 to 125C, VI= -19V, IO= 40 mA, CI= 0.33 F, CO= 0.1 F unless otherwise specified). ELECTRICAL CHARACTERISTICS OF L79L15 (refer to the test circuits, TJ= 0 to 125C, VI= -23V, IO= 40 mA, CI= 0.33 F, CO= 0.1 F unless otherwise specified). SymbolParameterTest ConditionsMin.Typ.Max.Unit VOOutput VoltageTJ= 25C-11.1-12-12.9V VOOutput VoltageIO= 1 to 40 mAVI= -14.5 to -27 V-10.8-13.2V IO= 1 to 70 mAVI= -19 V-10.8-13.2 VOLine RegulationVI= -14.5 to -27 VTJ= 25C250mV VI= -16 to -27 VTJ= 25C200 VOLoad RegulationIO= 1 to 100 mATJ= 25C100mV IO= 1 to 40 mATJ= 25C50 IdQuiescent CurrentTJ= 25C6.5mA TJ= 125C6 IdQuiescent Current ChangeIO= 1 to 40 mA0.2mA VI= -16 to -27 V1.5 eNOutput Noise VoltageB = 10Hz to 100KHzTJ= 25C80V SVRSupply Voltage RejectionIO= 40 mAf = 120HzTJ= 25C VI= -15 to -25 V 3642dB VdDropout Voltage1.7V SymbolParameterTest ConditionsMin.Typ.Max.Unit VOOutput VoltageTJ= 25C-13.8-15-16.2V VOOutput VoltageIO= 1 to 40 mAVI= -17.5 to -30 V-13.5-16.5V IO= 1 to 70 mAVI= -23 V-13.5-16.5 VOLine RegulationVI= -17.5 to -30 VTJ= 25C300mV VI= -20 to -30 VTJ= 25C250 VOLoad RegulationIO= 1 to 100 mATJ= 25C150mV IO= 1 to 40 mATJ= 25C75 IdQuiescent CurrentTJ= 25C6.5mA TJ= 125C6 IdQuiescent Current ChangeIO= 1 to 40 mA0.2mA VI= -20 to -30 V1.5 eNOutput Noise VoltageB = 10Hz to 100KHzTJ= 25C90V SVRSupply Voltage RejectionIO= 40 mAf = 120HzTJ= 25C VI= -18.5 to -28.5 V 3339dB VdDropout Voltage1.7V L79L00 SERIES 7/15 ELECTRICAL CHARACTERISTICS OF L79L05AB AND L79L05AC (refer to the test circuits, VI= -10V, IO= 40 mA, CI= 0.33 F, CO= 0.1 F, TJ= 0 to 125C for L79L05AC, TJ= -40 to 125C for L79L05AB, unless otherwise specified). ELECTRICAL CHARACTERISTICS OF L79L06AB AND L79L06AC (refer to the test circuits, VI= -12V, IO= 40 mA, CI= 0.33 F, CO= 0.1 F, TJ= 0 to 125C for L79L06AC, TJ= -40 to 125C for L79L06AB, unless otherwise specified). SymbolParameterTest ConditionsMin.Typ.Max.Unit VOOutput VoltageTJ= 25C-4.8-5-5.2V VOOutput VoltageIO= 1 to 40 mAVI= -7 to -20 V-4.75-5.25V IO= 1 to 70 mAVI= -10 V-4.75-5.25 VOLine RegulationVI= -7 to -20 VTJ= 25C150mV VI= -8 to -20 VTJ= 25C100 VOLoad RegulationIO= 1 to 100 mATJ= 25C60mV IO= 1 to 40 mATJ= 25C30 IdQuiescent CurrentTJ= 25C6mA TJ= 125C5.5 IdQuiescent Current ChangeIO= 1 to 40 mA0.1mA VI= -8 to -20 V1.5 eNOutput Noise VoltageB = 10Hz to 100KHzTJ= 25C40V SVRSupply Voltage RejectionIO= 40 mAf = 120HzTJ= 25C VI= -8 to -18 V 4149dB VdDropout Voltage1.7V SymbolParameterTest ConditionsMin.Typ.Max.Unit VOOutput VoltageTJ= 25C-5.76-6-6.24V VOOutput VoltageIO= 1 to 40 mAVI= -8.5 to -20 V-5.7-6.3V IO= 1 to 70 mAVI= -12 V-5.7-6.3 VOLine RegulationVI= -8.5 to -20 VTJ= 25C150mV VI= -9 to -20 VTJ= 25C100 VOLoad RegulationIO= 1 to 100 mATJ= 25C60mV IO= 1 to 40 mATJ= 25C30 IdQuiescent CurrentTJ= 25C6mA TJ= 125C5.5 IdQuiescent Current ChangeIO= 1 to 40 mA0.1mA VI= -9 to -20 V1.5 eNOutput Noise VoltageB = 10Hz to 100KHzTJ= 25C50V SVRSupply Voltage RejectionIO= 40 mAf = 120HzTJ= 25C VI= -9 to -20 V 3946dB VdDropout Voltage1.7V L79L00 SERIES 8/15 ELECTRICAL CHARACTERISTICS OF L79L08AB AND L79L08AC (refer to the test circuits, VI= -14V, IO= 40 mA, CI= 0.33 F, CO= 0.1 F, TJ= 0 to 125C for L79L08AC, TJ= -40 to 125C for L79L08AB, unless otherwise specified). ELECTRICAL CHARACTERISTICS OF L79L09AB AND L79L09AC (refer to the test circuits, VI= -15V, IO= 40 mA, CI= 0.33 F, CO= 0.1 F, TJ= 0 to 125C for L79L09AC, TJ= -40 to 125C for L79L09AB, unless otherwise specified). SymbolParameterTest ConditionsMin.Typ.Max.Unit VOOutput VoltageTJ= 25C-7.68-8-8.32V VOOutput VoltageIO= 1 to 40 mAVI= -10.5 to -23 V-7.6-8.4V IO= 1 to 70 mAVI= -14 V-7.6-8.4 VOLine RegulationVI= -10.5 to -23 VTJ= 25C175mV VI= -11 to -23 VTJ= 25C125 VOLoad RegulationIO= 1 to 100 mATJ= 25C80mV IO= 1 to 40 mATJ= 25C40 IdQuiescent CurrentTJ= 25C6mA TJ= 125C5.5 IdQuiescent Current ChangeIO= 1 to 40 mA0.1mA VI= -11 to -23 V1.5 eNOutput Noise VoltageB = 10Hz to 100KHzTJ= 25C60V SVRSupply Voltage RejectionIO= 40 mAf = 120HzTJ= 25C VI= -12 to -23 V 3745dB VdDropout Voltage1.7V SymbolParameterTest ConditionsMin.Typ.Max.Unit VOOutput VoltageTJ= 25C-8.64-9-9.36V VOOutput VoltageIO= 1 to 40 mAVI= -11.5 to -23 V-8.55-9.45V IO= 1 to 70 mAVI= -15 V-8.55-9.45 VOLine RegulationVI= -11.5 to -23 VTJ= 25C225mV VI= -12 to -23 VTJ= 25C150 VOLoad RegulationIO= 1 to 100 mATJ= 25C80mV IO= 1 to 40 mATJ= 25C40 IdQuiescent CurrentTJ= 25C6mA TJ= 125C5.5 IdQuiescent Current ChangeIO= 1 to 40 mA0.1mA VI= -12 to -23 V1.5 eNOutput Noise VoltageB = 10Hz to 100KHzTJ= 25C70V SVRSupply Voltage RejectionIO= 40 mAf = 120HzTJ= 25C VI= -12 to -23 V 3744dB VdDropout Voltage1.7V L79L00 SERIES 9/15 ELECTRICAL CHARACTERISTICS OF L79L12AB AND L79L12AC (refer to the test circuits, VI= -19V, IO= 40 mA, CI= 0.33 F, CO= 0.1 F, TJ= 0 to 125C for L79L12AC, TJ= -40 to 125C for L79L12AB, unless otherwise specified). ELECTRICAL CHARACTERISTICS OF L79L15AB AND L79L15AC (refer to the test circuits, VI= -23V, IO= 40 mA, CI= 0.33 F, CO= 0.1 F, TJ= 0 to 125C for L79L15AC, TJ= -40 to 125C for L79L15AB, unless otherwise specified). SymbolParameterTest ConditionsMin.Typ.Max.Unit VOOutput VoltageTJ= 25C-11.5-12-12.5V VOOutput VoltageIO= 1 to 40 mAVI= -14.5 to -27 V-11.4-12.6V IO= 1 to 70 mAVI= -19 V-11.4-12.6 VOLine RegulationVI= -14.5 to -27 VTJ= 25C250mV VI= -16 to -27 VTJ= 25C200 VOLoad RegulationIO= 1 to 100 mATJ= 25C100mV IO= 1 to 40 mATJ= 25C50 IdQuiescent CurrentTJ= 25C6.5mA TJ= 125C6 IdQuiescent Current ChangeIO= 1 to 40 mA0.1mA VI= -16 to -27 V1.5 eNOutput Noise VoltageB = 10Hz to 100KHzTJ= 25C80V SVRSupply Voltage RejectionIO= 40 mAf = 120HzTJ= 25C VI= -15 to -25 V 3742dB VdDropout Voltage1.7V SymbolParameterTest ConditionsMin.Typ.Max.Unit VOOutput VoltageTJ= 25C-14.4-15-15.6V VOOutput VoltageIO= 1 to 40 mAVI= -17.5 to -30 V-14.25-15.75V IO= 1 to 70 mAVI= -23 V-14.25-15.75 VOLine RegulationVI= -17.5 to -30 VTJ= 25C300mV VI= -20 to -30 VTJ= 25C250 VOLoad RegulationIO= 1 to 100 mATJ= 25C150mV IO= 1 to 40 mATJ= 25C75 IdQuiescent CurrentTJ= 25C6.5mA TJ= 125C6 IdQuiescent Current ChangeIO= 1 to 40 mA0.1mA VI= -20 to -30 V1.5 eNOutput Noise VoltageB = 10Hz to 100KHzTJ= 25C90V SVRSupply Voltage RejectionIO= 40 mAf = 120HzTJ= 25C VI= -18.5 to -28.5 V 3439dB VdDropout Voltage1.7V L79L00 SERIES 10/15 DIM. mm.inch MIN.TYPMAX.MIN.TYP.MAX. A1.351.750.0530.069 A40.010 A21.101.650.0430.065 B0.330.510.0130.020 C070.010 D4.805.000.1890.197 E3.804.000.1500.157 e1.270.050 H5.806.200.2280.244 h0.250.500.0100.020 L0.401.270.0160.050 k (max.) ddd0.10.04 SO-8 MECHANICAL DATA 0016023/C 8 L79L00 SERIES 11/15 DIM. s MIN.TYPMAX.MIN.TYP.MAX. A1.41.655.163.0 B0.440.5617.322.0 B10.360.4814.218.9 C0.350.4413.817.3 C10.350.4413.817.3 D4.44.6173.2181.1 D11.621.8363.872.0 E2.292.690.2102.4 e1.421.5755.961.8 e12.923.07115.0120.9 H3.944.25155.1167.3 L0.891.235.047.2 SOT-89 MECHANICAL DATA P025H L79L00 SERIES 12/15 DIM. s MIN.TYPMAX.MIN.TYP.MAX. A4.324.95170.1194.9 b0.360.5114.220.1 D4.454.95175.2194.9 E3.303.94129.9155.1 e2.412.6794.9105.1 e11.141.4044.955.1 L12.715.49500.0609.8 R2.162.4185.094.9 S10.921.5236.259.8 W0.410.5616.122.0 TO-92 MECHANICA DATA 0102782/C L79L00 SERIES 13/15 DIM. mm.inch MIN.TYPMAX.MIN.TYP.MAX. A33012.992 C12.813.20.5040.519 D20.20.795 N602.362 T22.40.882 Ao190.335 Bo160.232 Ko820.090 Po