变频器三菱E500(英文)

1、 MITSUBISHIINVERTER FREQROL E500INSTRUCTION MANUALCOMPACT GENERAL-PURPOSE INVERTERMITSUBISHI INVERTER INTECH一、 Basic Wiring Diagram：The basis of wiring diagram is for INTECH二、 Digital Keypad Operation：2.1 Key expression:KeyContents【RUN】Positive run command key.Built-in frequency setting deviceMay us

2、e analog method to change frequency setting【MODE】keySelection of RUN mode, setting mode【SET】keyPlease press the SET key after inputting frequency value, parameter set value.【/】keyl Continue ascend/descend adjusting key for run frequency, valid only pressing.l Press this key to make continuous change

3、 of the set value in setting mode【REV】keyReverse rotation command key【FWD】keyPositive rotation command key【STOP/RESET】keyl Run command stop keyl Inverter abnormal reset key2.2 Unit indication, run status indication:KeyContentsHZLight ON when the display value of the 7-stages monitor is frequency.ALi

4、ght ON when the display value of the 7-stages monitor is frequency.RUNLight ON during the inverter running, constant light ON when positive rotation, blinking while reverse.MONLight ON when under monitoring mode.PULight ON when under PU run mode.EXTLight ON when under external run mode.三、 Descriptio

5、n of function setting：四、Parameter setting：FunctionParameter numberNameEx-factory defaultINTECH SettingsMultiple stage selectionVR adjustmentBasic function0Manual torque compensation (note 1)6%4% (note 10)1Upper limit frequency120HzDepend on actual condition2Lower limit frequency0Hz3Base frequency (n

6、ote 1)60Hz43 speed setting (Hi)60Hz53 speed setting (Mid)30Hz63 speed setting (Lo)10Hz7Acceleration time5sec/10sec (note 4)10108Deceleration time5sec/15sec (note 4)10109Electronic thermal active relayRated output current (note 5)Depend on ratingDepend on ratingStandard operation function10Frequency

7、of DC brake action3Hz11Time of DC brake action0.5sec12DC brake voltage6%13Start frequency0.5Hz14Suitable load selection (note 1)015JOG frequency5Hz16JOG acceleration & deceleration time0.5sec18High speed upper limit frequency120HzOver 60Hz Depend on actual condition19Base frequency voltage (note 1)9

8、99920Acceleration & deceleration guideline frequency60Hz21Acceleration & deceleration time unit.022Stall prevention action level150%23Double speed stall prevention action level (note 6)999924Multiple stages speed setting (4 speed)999925Multiple stages speed setting (5 speed)999926Multiple stages spe

9、ed setting (6 speed)999927Multiple stages speed setting (7 speed)999929Acceleration & deceleration curve030Recovery function selection031Avoidance frequency 1A999932Avoidance frequency 1B999933Avoidance frequency 2A999934Avoidance frequency 2B999935Avoidance frequency 3A999936Avoidance frequency 3B9

10、99937Run speed indication038Frequency at 5V (10V) input60Hz (note 2)39Frequency while 20Ma input60Hz (note 2)Depend on actual conditionOutput function41Frequency reach amplitude of action10%42Output frequency detection6Hz43Output frequency detection while reverse rotation99992nd function44Second acc

11、eleration & deceleration time5sec/10sec(note 4)45Second deceleration time999946Second torque compensation (note 1)999947Second 2V/F basal frequency (note 1)999948Second electronic thermal active relay9999Display function52Selection of operating device/PU main display data054FM end sub- function sele

12、ction155Frequency display guideline60Hz56Current display guidelineRated output currentRe-start57Restart empty run time999958Restart ascend run time1.0 secAddition function59Remote setting function selection0Action selection function60Shortest acceleration & deceleration mode061Guideline current99996

13、2Current guideline value while acceleration999963Current guideline value while deceleration999965Auto reset selection066Stall prevention action reduction start frequency (note 6)60Hz67Number of reset while occurrence of abnormality03368Waiting time for executing auto reset1sec69Clear of frequency of

14、 auto reset execution070Special recovery brake0%71Applicable motor072PWM frequency selection1227305V、010V selection01174Filter time constant18875Reset selection/PU remove detection/PU stop selection1477Parameter lock selection02278Reverse rotation prevention selection01179Run mode selection (note 6)

15、122Motor constant80Motor capacity999982Motor energizing current9999 (note 3)83Motor rated voltage200/400V84Motor rated frequency60HzDepend on actual conditionDepend on actual condition90Motor constant (R1) (note 6)999996Automatic harmonic setting /status (note 6)0Communication function117Office numb

16、er0118Communication speed192119Stop bit length1120With or without identical bit check2121Times for communication retry1122Interval of communication confirming time0123Waiting tine setting9999124With or without CR-LF selection1PID control128PID action selection0129PID proportion band100%130PID integr

17、ation time1sec131Range of upper limit9999132Range of lower limit9999133Target value of PID action while PU run0%134PID differentiation time9999Addition function145Parameter for PU04 Peripheral146Frequency command setting selection0Addition function150Output current detecting level150%0151Output curr

18、ent detecting time0152Zero current detecting level5.0%153Zero current detecting time0.5secAuxiliary function156Stall prevention action selection0Addition function160User parameter group read out selection0Monitor recover171Memory clear of actual run time0User function173User first group registration

19、0174User first group registration0175User second group registration0176User second group registration0Terminal function selection180RL terminal function selection0181RM terminal function selection1182RH terminal function selection2183MRS terminal function selection68190RUN terminal function selectio

20、n0191FU terminal function selection4192ABC terminal function selection999999Multiple stage speed selection232Multiple stages speed setting (8 speed)9999(Depend on actual condition)60233Multiple stages speed setting (9 speed)9999(Depend on actual condition)50234Multiple stages speed setting (10 speed

21、)9999(Depend on actual condition)40235Multiple stages speed setting (11 speed)9999(Depend on actual condition)30236Multiple stages speed setting (12 speed)9999237Multiple stages speed setting (13 speed)9999238Multiple stages speed setting (14 speed)9999239Multiple stages speed setting (15 speed)9999

22、Auxiliary function240Soft-PWM setting1244Cooling fan action selection0Auxiliary function245Motor rated slide differential9999246Slide differential correction response time0.5sec247Fixed output field slide differential correction selection9999249With/without ground network detection while starting (n

23、ote 9)0STOP selection250Stop selection9999Calibration function900FM terminal calibration902Frequency setting voltage bias0Hz903Frequency setting voltage gain60Hz904Frequency setting current bias0Hz905Frequency setting current gain60Hz922Built-in frequency setting VR bias0Hz923Built-in frequency sett

24、ing VR gain60Hz990Key tone control of operating deviceNote ：1. These parameter setting will be ignored and void if selected under universal magnetic beam vector control mode.2. Calibration executed while ex-factory, the setting value of each inverter will be differing more or less to each other. The setting value will be slightly higher than 60Hz frequency setting.3. If the setting value exceeds 100Hz while using the operating device, t