基于MSP430F5438A单片机测量频率的程序实例

1、基于MSP430F5438A单片机测量频率的程序实例/*程序描述:利用Timer_A捕获脉冲宽度利用MSP430单片机定时器A和捕获/比较功能模块结合使用，实现脉冲宽度的测量程序用到了定时器A的CCI1A端口（MSP430F14X的P1.2引脚）作捕获外部输入的脉冲电平跳变，start,end,两个个变量来计算脉冲宽度*/#include msp430x14x.h#include lcd12864.huint start,end;uint width; /=用于存放脉宽=uint period; /=用于存放周期=uint frequency; /=用于存放频率=uint fy7; /=用于存

2、放频率显示数据=uint pd7; /=用于存放周期显示数据=uint wh6; /=用于存放脉宽显示数据=const unsigned char zhouqi=周期为:(us) ; const unsigned char us=us ;const unsigned char pinlv=频率为:(Hz) ;const unsigned char hz=HZ ;void process(void); /=函数声明=void delay(); /=延时函数=void InitSys(); /=初始化时钟=/* 主函数*/int main( void ) WDTCTL = WDTPW + WDTH

3、OLD; /=关狗= InitSys(); /=初始化时钟,SMCLK,MCLK均为8M= P1DIR&=BIT2; P1SEL = BIT2; /=设置P1.2端口为功能模块使用,即：做捕获源= TACTL = TASSEL_2+ID_3+TACLR+TAIE+MC1;/=定时器A时钟信号选择SMCLK,8分频,同时设置定时器A计数模式为连续增计模式= CCTL1 = CM_1+SCS+CAP+CCIE; /=输入上升沿捕获,CCI0A为捕获信号源= _EINT(); /=开全局中断允许= Ini_Lcd(); /=初始化液晶= Clear_GDRAM(); /=清屏= Disp_HZ(0x

4、80,zhouqi,8); Disp_HZ(0x88,pinlv,8); while(1) process(); Write_Cmd(0x90);/=写地址= Write_Data(0x30+pd6); Write_Data(0x30+pd5); Write_Data(0x30+pd4); Write_Data(0x30+pd3); Write_Data(0x30+pd2); Write_Data(0x30+pd1); Write_Data(0x30+pd0); Write_Cmd(0x98);/=写地址= Write_Data(0x30+fy6); Write_Data(0x30+fy5);

5、 Write_Data(0x30+fy4); Write_Data(0x30+fy3); Write_Data(0x30+fy2); Write_Data(0x30+fy1); Write_Data(0x30+fy0); delay(); /* 初始化时钟*/void InitSys() unsigned int i; /- 使用XT2振荡器 - BCSCTL1&=XT2OFF; /=打开XT2振荡器= do IFG1 &= OFIFG; /=清除振荡器失效标志= for (i = 0xFF; i 0; i-); /=延时，等待XT2起振= while (IFG1 & OFIFG) != 0)

6、; /=判断XT2是否起振= BCSCTL2 =SELM_2+SELS; /=选择MCLK、SMCLK为XT2,8M= /* 延时函数*/void delay() unsigned int i; unsigned int j=10; for(i=10;i0;i-) while(j-); /* 数据处理 */void process(void) while(endstart); /while(endstart width = end-start; /=实际脉冲宽度的计算= period = 2* width; frequency=/period; pd6=period/; pd5=(period

7、-*pd6)/; pd4=(period-*pd6-*pd5)/10000; pd3=(period-*pd6-*pd5-10000*pd4)/1000; pd2=(period-*pd6-*pd5-10000*pd4-1000*pd3)/100; pd1=(period-*pd6-*pd5-10000*pd4-1000*pd3-100*pd2)/10; pd0=period%10; fy6=frequency/; fy5=(frequency-*fy6)/; fy4=(frequency-*fy6-*fy5)/10000; fy3=(frequency-*fy6-*fy5-10000*fy4

8、)/1000; fy2=(frequency-*fy6-*fy5-10000*fy4-1000*fy3)/100; fy1=(frequency-*fy6-*fy5-10000*fy4-1000*fy3-100*fy2)/10; fy0=frequency%10;/* 中断处理函数*/#pragma vector=TIMERA1_VECTOR /=定时器A中断处理=_interrupt void timer_a(void) switch(TAIV) /=向量查询= case 2: /=捕获中断= if(CCTL1&CM0) /=捕获到上升沿= CCTL1=(CCTL1&(CM0)|CM1; /=更变设置为下降沿触发= start=TAR; /=记录初始时间= e