6工位回转刀架机械系统设计【含CAD图纸、说明书】
收藏
资源目录
压缩包内文档预览:
编号:115557435
类型:共享资源
大小:639.93KB
格式:ZIP
上传时间:2021-02-26
上传人:机****料
认证信息
个人认证
高**(实名认证)
河南
IP属地:河南
50
积分
- 关 键 词:
-
回转
刀架
机械
系统
设计
CAD
图纸
说明书
- 资源描述:
-
喜欢这个资料需要的话就充值下载吧。。。资源目录里展示的全都有预览可以查看的噢,,下载就有,,请放心下载,原稿可自行编辑修改=【QQ:11970985 可咨询交流】====================喜欢就充值下载吧。。。资源目录里展示的全都有,,下载后全都有,,请放心下载,原稿可自行编辑修改=【QQ:197216396 可咨询交流】====================
- 内容简介:
-
6 AUTOMATIC KNIFE KNIFE SYSTEM DESIGNABSTRACTNumerical Control lathe will be the middle and senior grade development in the future.It is estimated that the demand for NC tool carrier will be much greater. NC tool start to the rapid tool change, electro-hydraulic servo drive and portfolio-driven direction with the development of NC lathes. The mechanical structure and the control system of six Automatic Tool lift are designed in this thesis. Analyzing many plans, It be gotten that the blue print of the Automatic Tool Lift. And then,The structure be analyzed and calculated. At the same time, the ProE is used for the 3D solid modeling of mechanical structure, which shows the structure of the tool lift is reasonable. That PLC and sensors is applicated in the design of the soft and hard components of the tool lift .It makes the control of tool change more efficient.Automatic Tool Lift in this thesis, with its simple structure and rapid auxiliary tool change (ATC), will become an independent unit which can be used not only on general machine tools to reduce ATC time, but also on economic NC machine tools to improve the structure Tool.Key words: Automatic Tool lift, Sensors ,3D Solid Modeling, PLC目 录前言4第一章 总体设计1第二章 自动刀架系统机械部分设计22.1 刀架结构方案的确定22.1.1 刀架体设计22.1.2 传动方案设计22.1.3 定位方案的确定32.2 主要零部件设计计算32.2.1 刀具受力计算32.2.2 刀架体设计计算42.2.3 端齿盘主要参数的设计计算52.2.4 压缩弹簧设计102.2.5 蜗杆蜗轮设计112.2.6 螺杆、螺套设计及验算142.3 电机的选择162.4 联轴器结构选择172.5 润滑与密封17第三章 自动刀架控制部分设计183.1 控制系统分析183.1.1 控制方案设计183.1.2 PLC的分类183.1.3 PLC的特点及主要功能193.1.4 自动换刀控制系统要求213.2 检测元件的选择213.2.1 接近开关的类别223.2.2 接近开关的选择223.3 PLC选型233.3.1 分析控制系统所需的I/O接点数233.3.2 PLC外接电气元件选择233.4 系统控制元件列表243.5 PLC的I/O地址的分配253.6 PLC外围接线图26第四章 控制系统PLC程序设计274.1 系统流程图的设计274.2 PLC程序设计274.2.1 程序结
- 温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

人人文库网所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。