锂电保护板规格书

1、-!产品规格书SPECIFICATION客户Customer客户型号Customer Model项目名称Project NameJZ-JY-0011文件编号Docume nt NO受控版本Con trolled Revisi on实施日期Issued Date编制Registered审核Checked审核Checked审核Checked批准Approved批准Approved修订记录Modified Record产品修订记录表Product Modified Record List版本Revisio n变更内容Modified Content责任人Prin ciple日期Date标记Mark备

2、注NoteV1制样Sample mak ing、综述 Outline本规格书适合于深圳嘉智电子有限公司研制的1串锂动力电池保护板，本产品严格满足ROHS规范等。This specificati on applies to the 1 serial-cells lithium-i on battery protect ion board manu factured by SHENZHEN JIAZHI CO.,LTD, which strictly con forms to the ROHS sta ndard.、应用范围 Applicatio n锂充电电池包等。Applies to the l

3、ithium-i on rechargeable battery packs and so on.、电气特性 Electronic characteristic(Ta=25°C)测试项目test item详细内容content最小值mi nimu m典型值typical最大值maximum单位unit备注note参 数 配 置CFG过充over charge单节过充保护over-charge protect ion foreach cell4.2504.3004.350V单节过充保护延迟时间 over-charge protect ion delay time for each ce

4、ll0.82.0S单节过充保护恢复 over-charge recover protecti on recover for each cell4.0504.1004.150V过放over dischar ge单节过放保护over-discharge protect ionfor each cell2.3002.4002.500V单节过放保护延迟时间 over-discharge protect ion delay time for each cell2060mS单节过放保护恢复 over-discharge recover protect ion for each cell2.9003.000

5、3.100V测试项目test item详细内容content最小值min典型值typical最大值max单位unit备注note过流及 短路Over curre nt & short circuit放电过流保护 discharge over curre nt protectio n369A短路保护short circuit protect ion有YES放电过流保护延迟时间 discharge protection delay time1020mS正常充电电流no rmal charg ing curre nt1.8A正常放电电流no rmal discharg ing curre n

6、t1.8A均衡bala nee均衡开启电压bala nee start voltage/V均衡电流bala nee curre nt/mA测试项目test item详细内容content最小值min典型值typical最大值max单位unit备注note参 数 配 置CFG温度保 护/充 电temper ature protecti on/charge过温保护over temperature protectio n/C过温保护恢复over temperature protecti on recover/C温度保 护/放 电temper ature protecti on /discharge过

7、温保护over temperature protectio n/C过温保护恢复over temperature protecti on recover/C测试项目test item详细内容content备注note恢复方式RecoveryMode放电过流保护 discharge over curre nt protectio n断开负载后恢复It will recover after cutting off the load短路保护short circuit protect ion断开负载后恢复It will recover after cutting off the load高温保护over

8、 temperature protectio n/过充保护over-charge protect ion低于过充恢复值un der the over-voltage recover value过放保护over-discharge protect ion充电恢复Charg ing静态功耗sleep modeMAX : 7uA内阻in ternalresista neeMAX : 40m Q结构尺寸dime nsion13*0.6mm四、工作环境和贮存环境条件Work ing con diti on and storage con diti on工作环境条件worki ngcon diti on项

9、目item标准sta ndard备注note工作温度范围the work ing temperaturerange-30 85C在此范围工作正常n ormally work相对湿度relative humidity5% 95%长期工作，无冷凝worklongtime,nocondensing大气压atmospheric pressure86 106 KPa贮存环境条件storage con diti on温度humidity-40 C 95 C相对湿度relative humidity< 75%大气压atmospheric pressure86kPa106kPa五、连线示意图及连接步骤L

10、inking diagram and connecting steps充电ll-«菁正极1、充电接线方式 the charging connecting method : 充电器负极接P-;P-conn ects to the cathode of the charg ing; 充电器正极接B+;B+ conn ects to the Anode of the charg ing;2、放电接线方式the discharging connecting method :负载负极接P-;P- pads conn ects to the cathode of the loader;负载正极接

11、B+。B+ conn ects to the anode of the charg ing.3、注意事项notes：，请用专用充电器充电激活。 若仍有异常，请与将电池和本保护板组合好以后，初次上电时，如果发现无电压输出 厂家联系。After assembling the battery and the protection board, if there is no voltage output when your first power on, please charge the battery with the special charger and it will work no rma

12、l.If there is still abno rmal, please con tact us.六、使用和组装的注意事项The no tes of using and assembli ng1、焊接电池引线时，一定要小心，不可接错或反接。如发觉接错后，这块电路板有可能已经损坏，需要经过重 新测试合格后才可以再次使用。Be careful and make sure not connect wrong or oppositely when weld the lead wire. It can be used after the re-test is ok because the PCBA m

13、ay have bee n destroyed whe n the wrong connection.2、装配时BMS不要直接接触到电芯表面，以免损坏电芯。装配要牢固可靠。BMS do not touch the cell surface in order to preve nt from destro ying cell whe n you assembli ng. Make sure assembli ng stable and reliable.3、使用中注意引线头、烙铁等不要碰到电路板上的元器件，否则有可能损坏本电路板。Do not touch the components in th

14、e PCBA in order to prevent from destroying the board when use the wire, soldering iron.4、使用过程要注意防静电，防潮和防水等。Pay attention to the antistatic, damp proof, waterproof and so on.5、使用过程中请遵循设计参数及使用条件，不得超过本规格书中的值，否则有可能损坏本保护板。Make sure the design parameters and working condition which are under the value in

15、the specification, or else may destroy the PCBA.七：环境物质要求 Environmen tal Requireme nts本规格书内容符合欧盟RoHS指令要求，有害物质含量符合以下标准：The specificati on subjects to the EU Directive about RoHS, and the hazardous substa nce con forms to the followi ng sta ndard.有害物质 hazardous substance基准 standardCadmium and its compounds:镉(Cd)及其化合物V100PPMLead and its compounds:铅(Pb)及其化合物V1000PPMMercury and its compounds: 汞(Hg)及其化合物<1000PPMChromium( W ) and its compounds:六价铬(Cr6+)及其化合物V1000PPM非电镀）禁用(电镀)forbid platingPolybrominated biphenyls(PBBs):多溴联苯<1000PPMPo