Bezzazi_Experimental-characterization-of-frictional-behaviour-of-clutch-facings-using-Pin-on-disk-machine_2007.pdf

电磁离合器性能测试台设计

收藏

资源目录
跳过导航链接。
压缩包内文档预览:
预览图 预览图 预览图 预览图 预览图 预览图
编号:171730649    类型:共享资源    大小:3.07MB    格式:ZIP    上传时间:2021-12-04 上传人:好资料QQ****51605 IP属地:江苏
45
积分
关 键 词:
电磁离合器 性能 测试 设计
资源描述:

喜欢这套资料就充值下载吧。资源目录里展示的都可在线预览哦。下载后都有,请放心下载,文件全都包含在内,有疑问咨询QQ:414951605 或 1304139763

内容简介:
Experimental characterization of frictional behaviour of clutchfacings using Pin-on-disk machineM. Bezzazia, A. Khamlichia,*, A. Jabbouria, P. Reisb, J.P. DavimbaLMMS, De partement de Physique, F.S.T.T, B.P. 416, Tangier, MoroccobDepartamento de Engenharia Meca nica, Universidade do Aveiro, PortugalReceived 24 January 2006Available online 1 September 2006AbstractDuring the clutch engagement manoeuvre, sliding contact occurs between the pair of clutch facings mounted on the friction disk andthe counter faces belonging to the flywheel and the pressure plate. The transmitted torque is proportional to the overall coefficient offriction which depends essentially on temperature, normal pressure load and relative sliding velocity. In this work, performance ofthe friction coefficient is investigated experimentally. Samples of a commercial clutch facings material have been tested using a Pin-on-disk apparatus. When the previous three parameters are preset constant, this machine provides automatic acquisition of friction coef-ficient and wear measurements. The obtained results are compared with the classical SAE J661a standard test. It is found that the actualclutch facings material has good fading resistance and a rather stable coefficient of friction once running in phase is achieved.? 2006 Elsevier Ltd. All rights reserved.Keywords: Composites; Thermal; Mechanical; Friction behaviour; Clutch facings1. IntroductionIn a vehicle rotary motion is to be transmitted from theprimary shaft (motor) to the secondary shaft (gear box) forintermittent periods only. To achieve that, a clutch isrequired between these two components. The function ofthe clutch is to produce a soft gradual increase in the angu-lar velocity of the driven shaft until full coupling betweenthe motor and the gear box is achieved. Then, the clutchmust act as a permanent coupling transmitting, from thedriving shaft to the vehicle wheels, the entire mechanicalpower without subsequent slip 1.During dry clutch engagement manoeuvre, a transientsliding contact situation occurs between the pair of clutchfacings mounted on the friction disk and the counter facesbelonging to the flywheel and the pressure plate. Through-out this engagement process, heat is generated at the con-tact surface yielding temperature to rise 2. Temperaturerise may be very important in case of repetitive engage-ments. Good performances of the clutch facings materialsuch as a stable and sufficiently high coefficient of frictionare required in order to operate engagements in an efficientand regular way. Fading phenomenon which is due to asudden decrease of the friction coefficient as function oftemperature must be avoided. Variations in time of the fric-tion coefficient during the running in phase or due to mate-rial wear must also remain limited.Other factors in addition to temperature might influencethe coefficient of friction level. They are related to hetero-geneities of the contact surfaces, chemical reactions orphysical transformations. But, these mechanisms are bothcomplex and non reproducible. Their effects could be, inpractice, globally taken into account through the coeffi-cient of friction tolerances.To characterize the tribological behaviour of clutch fac-ings, a lot of standard laboratory tests are usually per-formed by the manufacturers: Raybestos tests in case of0261-3069/$ - see front matter ? 2006 Elsevier Ltd. All rights reserved.doi:10.1016/j.matdes.2006.07.001*Corresponding author. Address: 33, Re sidence Al Isma lia, Avenue desF.A.R., Appt. 15B, Tetouan, Morocco. Tel.: +212 67 79 50 68; fax: +21239 35 07 02.E-mail address: khamlichi7 (A. Khamlichi)./locate/matdesMaterials and Design 28 (2007) 21482153Materials& DesignEurope 3, JIS D-4311 in case of Japan 4 and SAE J661atest in case of USA 5. But, most of these tests are bothlengthy and costly. This makes them difficult to use in realresearch and development operations. So, they should berather kept to the final stage in order to assess the materialcommercial specifications. Other basic tests which are morecost effective should be used in order to facilitate morequickly information about fiction and wear behaviours.In case of friction products, the well known FAST test 5is a quick and inexpensive test. However, it suffers from thepathological apparition of glazing effect. This effect is oftenencountered for polymeric composite materials due to lackof cleaning the friction surface in the FAST test. Apparentglazing has in general nothing to do with real conditionsof product working because the friction surface is perma-nently cleaned in real servicing life of friction products.In the special case of metal pairs 6, and PEEK-CF30/steel 7,8 the Pin-on-disc has proven to be one of the mosteffective test configurations which allow a reliable andquick determination of coefficient of friction and wear.In this work, we have investigated the opportunity touse the Pin-on-disk test in order to study the dry tribolog-ical behaviour of commercial organic clutch facings whichare manufactured according to the scatter wound proce-dure. For this purpose, special samples of clutch facingsmaterial having the form of disks and special pins madefrom steel were manufactured. The inverse operating con-figuration in comparison with the habitual technique ofusing the Pin-on-disk apparatus was chosen in order to per-form the friction and wear tests. These conditions arethought to enable the friction surface cleaning and to avoidartificial glazing.Through this experiment, we have studied the frictioncoefficient behaviour as function of temperature, slidingvelocity and sliding distance. Load pressure was keptalmost constant. Wear was also measured as function ofthe previous parameters.The obtained results are presented in the following ascharts giving the friction coefficient, l, versus the slidingdistance when temperature, T, and the sliding velocity, v,are set constant. Qualitative comparison with the classicalSAE J661a test is then performed. They show in particularthat glazing effect does not occur during testing. The fric-tion product is found to have a stable coefficient of frictionand does not suffer from fading phenomenon.2. Clutch facing material description2.1. Clutch facing material formulation and themanufacturing processOrganic clutch facings are composites witch are manu-factured in the most common case according to the scatterwound procedure. First a balanced formula is given. Thisconsists of a fibre glass yarn fitted with a copper strip inorder to enhance conductivity and to relieve heat evacua-tion from the facing surface during clutch operation. Theformula contains also the weight composition of theimpregnating mixture which holds in general more than fif-teen raw materials. These materials are bonded by meansof a phenolic resin which is put in the impregnant mixturewith a proportion of about 30% by weight.The manufacturing steps as described in 5 are asfollows:(1) Impregnation. A yarn is placed into an impregnatingtank which is filled with the impregnant solution. Vis-cosity is modified by adding organic solvent in orderto improve the mixture absorption by yarn.(2) Drain and preliminary bake. Rack of impregnatedyarn is lifted from impregnant and allowed to drainin an air circulating oven to remove the extra solventand to produce a relatively stiffyarn.(3) Preforming. This needs an automatic preformingmachine and special platens. The dry yarn is forcedto form a tracing which enables even distribution ofmatter over the preform surface.(4) Flat press and final bake. The preform is put into aheated mould and highly pressed during a short cur-ing cycle. Then, rings are stacked in piles on a flat sur-face and under weights to keep flat and placed into anoven during a long and smooth curing cycle.(5) Grinding to thickness and turn and bore. Grinding isdone on a double disc grinder. Then the rings areplaced on the boring bar in order to have the desireddiameters.After all these operations, anti corrosion surface treat-ment of clutch facings is achieved and drilling in accordwith a specified drawing can be performed. The clutch fac-ings are then ready to fit a friction disk.2.2. Clutch facing morphologyThe clutch facing morphology is in general very hetero-geneous. But it could roughly be defined by the threedimensional tracing achieved by the impregnated yarn dur-ing the preforming operation. Some irregularities mayaffect the overall yarn tracing due to certain deformationsoccurring during moulding or because of material removalneeded in grinding operations. Yarn tracing results in theactual preforming machine from superposing two basicmovements of the pipe: a radial sinusoidal translation withangular frequency x1and a uniform circular rotation withspeed x2, a = x1/x2defines the preforming ratio. Thisparameter controls to a large extent the clutch facingmorphology.For some given material formulation and for some com-mercial reference application of the clutch facing whichcorresponds to outer radius Ro, inner radius Riand thick-ness e, the facing texture depends on how the preform isoutfitted.Using polar coordinates (r,h), the location of an arbi-trary point of the yarn tracing is given, as studied in 2,M. Bezzazi et al. / Materials and Design 28 (2007) 214821532149byr(t) = Rm+ hsin(x1t)andh(t) = x2t,whereRm= (Ro+ Ri)/2 is the mean radius of the clutch facingand h = (Ro? Ri)/2.Fig. 1 gives the clutch facing morphology whereRo= 100 mm, Ri= 67 mm, e = 3.35 mm, x2= 180 rpmand a = 4.27. The chosen value of a enables optimal mate-rial distribution over the clutch facing surface, 2.3. Tribological tests3.1. Tribometer Pin-on-diskFriction and wear tests, on polymeric composite clutchfacings material under unlubricated conditions, were per-formed on a Pin-on-disk tribometer PLINT TE67HT?.The objective was to evaluate the behaviour of the compos-ite material/steel pair under the effect of sliding distance,sliding velocity, normal load and temperature.The tribometer, as shown in Fig. 2, consists of a loadingstationary pin sliding against a rotating disk with its axisperpendicular to the disk. The test disk is mounted onthe disk carrier spindle and secured by a central bolt. Thepins specimens were clamped in the collet chuck and fixedin a loading arm. The pins stayed over the disks with twofreedom degrees: a vertical one, which allows normal loadapplication by direct contact with the surface of the disk,and a horizontal one, for friction measurement. The nor-mal load applied on the pin is provided by a pneumatic sys-tem with a compression load cell. A motor with atachogenerator feedback ensured the stable running speeds.An indication of wear process in the pin/disk contact wasgiven by a linear potentiometer mounted in the pneumaticpin-loading piston.3.2. Tribological conditionsDIN Ck45K steel pins (flat-ended) with a diameter of8 mm and a length of 67.8 mm were machined. All pinshave the following chemical composition (wt.%): 0.45%C,0.25%Si, 0.65%Mn and present a hardness value of230 HB. Before testing the pins were ultrasonically cleanedin an acetone bath.Organic friction material discs with 8 mm thickness and76 mm of diameter were manufactured and used as counterface.Table 1 shows the tribological conditions used on teststo evaluate the behaviour of composite material/steel pair.These conditions were chosen so that the load pressure Premains almost constant during the tests. Two test temper-atures were chosen: ambient temperature and 100 ?C. Tem-perature is stabilized by a controlled heating system. Allthe experiments were performed under dry sliding condi-tions with a relative humidity of about 50%.3.3. Chase machine and standard SAE J661aThe Chase machine is well established as a means ofdetermining friction levels for clutch facings material. AsampleforChasetestinghasthedimensions25.4 mm 25.4 mm 6 mm. The test procedure is accord-ing to SAE standard J661a. It begins with a bedding in(running in) of 20 applications, 10 s on, 20 s off, with fric-tion readings at every fifth application. This is followed bya drag test where the test drum temperature is allowed torise to 550 ?F (288 ?C). During the recovery part of the testthe drum is allowed to cool, and the brake is applied, andfriction readings taken, at 100 ?F (37.8 ?C) intervals. Thewear portion of the test consists of 100 applications at400 ?F (204.4 ?C), 20 s on, 10 s off. This is followed by asecond fade and recovery test. Similar to the first, but withFig. 1. Clutch facing morphology for a = 4.27.Fig. 2. Tribometer PLINT TE67HT?.Table 1Tribological conditions used on testsSliding velocity (m/s)Sliding distance (m)31000110002150M. Bezzazi et al. / Materials and Design 28 (2007) 21482153temperatures going up to 650 ?F (343.3 ?C). Finally a base-line like the one at the beginning is performed. Test sam-ples are weighed and thickness is measured before andafter testing to get some idea of wear.4. Experimental friction charts obtained by Pin-on-diskmachineThe obtained experimental results with the Pin-on-diskmachine are depicted in the following figures as curves giv-ing the friction coefficient l versus the sliding distance.Fig. 4(a) and (b) are associated with almost the sameexperimental conditions but the sample disk was returnedin case of Fig. 4(a), so the friction surface material in con-tact with the pin is the backward surface in the first caseand the forward surface in the second case. This surfacewas used also for the subsequent tests. One can notice thatthe friction coefficient becomes stable in Fig. 4(a) and (b)for high sliding distances. But the reached levels are slightlydifferent: 0.27 for Fig. 4(a) and 0.33 for Fig. 4(b). However,during the running in phase (estimated at 200 m) the fric-tion coefficient behaviour is quite different from one faceto the other. This is mainly due to the manufacturing pro-cess and to the heterogeneous texture of the friction mate-rial surface as depicted in Fig. 1. These variations areconsidered here as defining tolerances of the friction coeffi-cient. After the running in phase they are found to be lim-ited to 0.06.The same remarks about the stable behaviour of the fric-tion coefficient can be formulated in case of Fig. 4(c)(e).The running in phase is found in these last cases to beshorter. Explanation of this could be related to the amountof the frictional work which is here higher, so only a smal-ler sliding distance is required.It should be noticed also that temperature measure-ments were performed during Pin-on-disk testing on thedisk lateral side. This temperature is not equal to that ofthe friction surface between the pin and the disk. More-over, this last temperature is always higher than the lateraldisk temperature due to heating resulting from the fric-tional work. Since the generated heat increases withincreasing sliding velocity, the spot temperature at the con-tact surface between the pin and the friction material willincrease if sliding velocity is increased.Organic polymeric friction materials sliding against steelor cast iron are known to have a friction coefficient whichdecreases with temperature after reaching a maximum 9.This is in agreement with Table 2 results since the frictioncoefficient is in all cases decreasing with increasing slidingvelocity or temperature. Effect of sliding velocity variationsis found also to be higher than that associated with temper-ature variations.Finally, one can notice that in all the previous tests thefriction coefficient behaviour is rather stable and does notshow huge fluctuations from the mean level. The frictioncoefficient level remains also high even for the hard condi-tions corresponding to v = 3 m/s. For the special clutchfacing material having been tested, fading is found to beoutside the range of parameters investigated in the presentstudy.5. Comparison with other testing resultsFig. 5 gives the friction coefficient versus temperatureduring the seven phases of the SAE J661a test. The pres-sure load acting on the clutch facing sample is almost thesame than that used in the Pin-on-disk testing. Tempera-ture is measured on the drum, Fig. 3. So, one could expectto find a significant difference between temperature used inthe Pin-on-disk test and temperature given in Fig. 5.Another difference between these two tests is due to thecounter friction surface used in the SAE J661a which ismade from cast iron, whereas for the Pin-on-disk it is madefrom steel. Also, samples used in the SAE J661a are only4 mm thick and are taken from daily life productionwhereas the tested disks on the Pin-on-disk machine are8 mm thick. Differences between these two tests regardingthe coefficient of friction level are expected to exceed theabove mentioned tolerance of 0.06.From the previous discussion it results that only a qual-itative comparison could be done between Figs. 4(a)(e)and 5. This however shows that the coefficient of frictionbehaviour as function of temperature is well characterizedby the Pin-on-disk tests, Fig. 4(a)(e). In fact, to reach thesame average level of the friction coefficient as in these lasttests, temperature could be shifted right in Fig. 5. Takinginto account coefficient of friction tolerances, the tempera-ture variation is found actually to exceed 100 ?C. This factPPFig. 3. Chase machine sketch.Table 2Computed average coefficient of frictionSliding velocity(m/s)Temperature(?C)Pressure(N)Frictioncoefficient1100510.271100530.333100560.191200580.323200510.17M. Bezzazi et al. / Materials and Design 28 (2007) 214821532151was verified during Pin-on-disk testing by means of a ther-mocouple which was set on the wear path.6. ConclusionsFor the friction material of clutch facings considered inthis experimental work the mean conclusions found couldbe stated as follows: after running in, the friction coefficient is essentially sta-ble at a level which depends on both the sliding velocityand temperature; the friction coefficient decreases with increasing temper-ature and with increasing sliding velocity.Comparison of Pin-on-disk results with those obtainedthrough SAE J661a standard test, which was performedon the same clutch facing material, shows that the usualfeatures regarding the coefficient of friction behaviour areidentical if differences of temperature are incorporated.Using the clutch facing material as the disk in the Pin-on-disk machine enables to eliminate glazing effect whichis frequently observed on other tests where the frictionmaterial is reduced to a small sample which is bonded onthe pin like for example the FAST test.The tests carried out in the present study have assessedthat the most desired perfor
温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
提示  人人文库网所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。
关于本文
本文标题:电磁离合器性能测试台设计
链接地址:https://www.renrendoc.com/paper/171730649.html

官方联系方式

2:不支持迅雷下载,请使用浏览器下载   
3:不支持QQ浏览器下载,请用其他浏览器   
4:下载后的文档和图纸-无水印   
5:文档经过压缩,下载后原文更清晰   
关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

网站客服QQ:2881952447     

copyright@ 2020-2025  renrendoc.com 人人文库版权所有   联系电话:400-852-1180

备案号:蜀ICP备2022000484号-2       经营许可证: 川B2-20220663       公网安备川公网安备: 51019002004831号

本站为文档C2C交易模式,即用户上传的文档直接被用户下载,本站只是中间服务平台,本站所有文档下载所得的收益归上传人(含作者)所有。人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。若文档所含内容侵犯了您的版权或隐私,请立即通知人人文库网,我们立即给予删除!