教材：石油钻井常用英语手册

1、A Handbook of English for Oil Drilling石油钻井常用英语手册石油钻井常用英语手册职工培训教材系列职工培训教材系列辽河石油勘探局钻井二公司六分公司辽河石油勘探局钻井二公司六分公司二二 OO 七年四月七年四月1A Handbook of English for Oil Drilling石油钻井常用英语手册石油钻井常用英语手册一、一、DRILLING 钻井钻井 1.Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业. 2.Prepared bell ni

2、pple. 准备”喇叭口”短节. 3.Make up 2 joints of drill pipe. 接两根钻杆. 4.Break out this connection. 卸开该接头. 5.Make up bottom hole assembly. 组合下部钻具 6.Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置. 7.Number stands on trip out and trip in. 起下钻时给立柱编号. 8.Pick up BHA and run to seafloor. 将下部钻具下到海底. 9.Pi

3、ck up stands. 接立柱 10.Dont drill faster than 15 minutes for 1 stand. 钻进速度别超过 15 分钟 1 根立柱 11.Drop TOTCO. 投(陶特)测斜仪 12.Fish TOTCO with overshot. 用打捞筒捞起测斜仪 13.Resume drilling to T.D. 继续钻进到总深 14.Circulate 15 minutes.循环 15 分钟 15.Run in hole. 下钻 16.Put out of hole. 起钻 17.Make an inventory of all ring gasket

4、s. 开一个所有垫圈的清单 18.Use spinning tong. 使用气动扳手 19.Operate the air winch. 操作气动绞车 20.Lay down 57 joints of 5” drill pipe. 甩 57 根钻杆 21.Pick up drill stem test tool. 提起钻杆测试工具 22.Circulate mud for 2 hours. 循环泥浆 2 小时 23.Move string during circulation. 在循环时注意活动钻具 24.Circulate hole clean. 循环清洗井眼 25.Circulate bo

5、ttoms up. 循环泥浆几周 26.Fill up every 5 stands. 每 5 柱灌泥浆一次 27.Check mud weight every 15 minutes. 每 15 分钟检查泥浆比重 28.Reverse out excess cement. 反循环替出多余的泥浆 29.Change/replace old mud by new mud. 用新的泥浆替换出旧的泥浆 30.Stop drilling. 停止钻进 31.Drilling ahead. 钻进 32.Pull out of hole bit. 起出钻头 33.Change bit. 换钻头 34.Run

6、the wear bushing. 下抗磨补心 35.The bit thread type is regular pin. 钻头丝扣是正规公扣 36.Whats the make-up torque? 上扣扭矩要多大? 37.Run in 9” collars. 下 9”钻铤238.The cathead cant give enough torque. 猫头力量不够 39.Connect crossover sub. 接上配合接头 40.The tong angle is too small. 大钳的角度太小了 41.Stop circulating. 停止循环泥浆 42.Break ou

7、t the stand. 卸立柱 43.Set the single into the mousehole. 把这个单根放进鼠洞 44.Can we break out the pipe with rotary table? 可用转盘卸扣吗? 45.No! Break it out with tong. 不行! 要用大钳卸扣 46.Spin it out with the air spanner. 用气动扳手卸扣 47.Put the pipe wiper on the string. 装上钻杆刮泥器 48.Dont set this stand back. 这根钻杆不要放在钻杆盒上 49.M

8、ake up the lift sub. 接好提升短节 50.Secure the safety clamp. 上紧安全卡瓦 51.The bit is nearing the shoe. 钻头快到套管鞋了 52.Slow down the running speed. 放慢下放速度 53.This is the undergauged interval. 这是缩径井段 54.This is the drilling program. 这是钻井设计书 55.How much weight on bit is required? 要加多少钻压? 56.Keep the rotary speed

9、at 120-140 RPM. 转速保持 120-140 转/分 57.Keep the flow rate at 3000 LPM. 保持排量 3000 升/分 58.The pump pressure is too high. 泵压太高了 59.Dont ream the hole too fast. 划眼不要太快 60.Notice the rotary torque. 注意转盘扭矩的变化 61.The penetration rate is getting slower. 钻速变慢了 62.The bit is nearly worn out. 钻头快磨光了 63.Stop drill

10、ing at 2000 meters. 钻至 2000 米停钻 64.Circulate for one hour. 循环一个小时 65.The pump pressure has increased. 泵压升高了 66.One nozzle may be plugged. 可能有一个水眼(或: 喷嘴)堵了 67.What is the hook load? 悬重多少? 68.Whats the pick-up weight? 上提重量是多少? 69.Whats the lowering weight? 下放重量是多少? 70.Run in HWDP. 下加重钻杆 71.A stabilize

11、r is needed here. 这里需要一个扶正器 72.This is a flexible sub. 这是挠性接头 73.This is the BHA log. 这是下部钻具组合记录 74.Record all outside and inside diameters. 记录好所有(入井工具的)内外径 75.We need a short drill collar. 需要一根短钻铤 76.Pull the cat line. 拉猫头 77.Operate the break lever. 操作(或:扶)刹把 78.Stop the pumps. 停泵 79.Make a wiper

12、trip. 通井 80.Retrieve wear bushing. 取出抗磨补心 81.Bleed off pressure. (释)放压(力) 82.Keep 5 wraps on the drum. 滚筒上留 5 圈 83.Set slips. 座上卡瓦 384.If tight hole, repeat wiper trip. 如果井眼紧, 重复划眼 85.Setback bottom hole assembly. 将下部钻具立于钻杆盒内 86.Make sure all alarms are on. 确保所有的警报信号都开着 87.Lay down TDS spinner. 拆下顶部

13、驱动的旋扣器 88.Run in hole bit #15 to bottom. 用 15 号钻头下钻到井底 89.Run in hole to casing shoe. 下钻至套管鞋 90.Pick up same bit and BHA. 装上同样的钻头和钻具组合 91.Lay down 5” HW drill pipe. 甩 5”加重钻杆 92.Move string every 2 hours. 每 2 小时活动钻具一次 93.Keep area around shaker clean. 保持振动筛区域干净 94.Control trip gas. 控制起下钻气 95.Ream if

14、needed. 如必要时进行划眼 96.Select the best penetration rate. 选择最佳钻进速度 97.Fix the traveling assembly. 固定游动系统98.Check power tongs and spinning rope are on drill floor. 检查动力钳和尾绳是否在钻台99.Whats the weight on bit? 钻压是多少? 100.What is the BHA of this well? 这口井的下部钻具如何组合? 101.Drill out cement. 钻穿水泥 102.Drill out 20”

15、casing shoe. 钻穿 20”套管鞋 103.Latch the elevator. 扣吊卡 104.Unlatch the elevator. 开吊卡 105.Set the slips. 放卡瓦 106.Adjust the crown-o-matic (crown saver). 调整防碰天车 107.Lock the hook pin. 锁紧大钩销子 108.Check OD of stabilizer. 检查扶正器的外径 109.Perform leak off test. 进行地层破裂(或:渗漏)测试 110.Connect kill and choke line. 接上压

16、井和放喷管线 111.Reverse out the drill pipe. 反循环清洗钻杆 112.Make a short trip. 进行短途起下钻 113.Change the cutters. 换割刀 114.Slug the pipe. 灌重泥浆 115.Drill the stand down. 钻完立柱 116.Start/run the shale shaker. 开振动筛 117.Start the desanders. 开除砂器 118.Start the desilters. 开除泥器 119.Change it with a 40 mesh screen. 换成 40

17、 目筛布 120.Shut it off. 关掉 121.Pull it to the cat ramp. 把它拉到坡道上去 122.Make a fast connection. 接单根要快 123.Dont dump the mud into the sea. 不要把泥浆排放到海里 124.Disconnect it with a chain tong. 用链钳卸开 125.Put a thread protector. 加一个(丝扣)护箍 126.Can we use the power slips? 可以使用动力卡瓦吗?二、二、CASING AND CEMENTING 下套管与固井下套

18、管与固井4127.Run in hole to bottom for wiper trip. 下钻通井 128.This is the casing program. 这是套管程序 129.Prepare for running casing. 准备下套管 130.Make everything ready for running 7”casing. 做好下 7”套管的准备 131.Make cementing job. 固井 132.Displace cementing with mud pump. 用泥浆泵替泥浆 133.Set cement plug from 2940 to 2790m

19、. 在 2940 到 2790 米井段打水泥塞 134.Pick up cementing head. 接水泥头 135.Cement samples are hard. 水泥样已凝固 136.Pump in 3 cubic meters of spacer. 注 3 方隔离液 137.Pump down the plug. 泵压(胶)塞 138.Wait on cement. 候凝 139.The guide shoe will be connected. 接引鞋 140.Connect the floor collar. 接浮箍 141.Connect the air line to th

20、e casing stabbing board. 接好套管 扶正台的气管线 142.Run casing with the 350T slip elevator. 用 350 吨卡瓦式吊卡下套管 143.Clean and dry 20” casing threads with rags. 清洁并擦干 20”套管丝扣 144.Where is the rabbit for drifting the casing? 套管通径规在哪里?三、三、FISHING 打捞打捞145.The bit cutters have been lost in the hole. 牙轮落井 146.Run in th

21、e reverse-circulation basket. 下反循环打捞篮 147.There is a lot of junk in the hole. 井下有很多落物 148.The fish is 235.46 meters long. 落鱼长度 235.46 米 149.The fish top is at 2478.34 meters. 鱼顶位置 2478.34 米四、四、FREEING STUCK PIPE 卡钻与解卡卡钻与解卡190.The down-hole problems are very complicated. 井下情况很复杂 191.The hole is tight

22、. 遇阻了 192.Overpull while tripping out. 起钻遇卡(overpull: 超拉力) 193.The formation is unstable. 地层不稳定 194.The wall caving is severe. 井壁垮塌严重 195.There are many return cuttings. 返出岩屑特别多 196.The mud returns have decreased. 返出泥浆减少 197.The hole is enlarged. 井眼扩大了 198.The pipes stuck. 卡钻了 199.Pull up to 150 ton

23、s. 上提 150 吨 200.Slack off to 50 tons. 下放至 50 吨 201.Ream down all the tight points. 在所有遇阻点进行划眼 202.The rotary table cant rotate. 转盘转不动203.Where is the sticking point? 卡点在哪里 204.Make a tensile test. 做拉伸试验 205.Back it off above the free point. 在卡点以上倒扣 206.Where is the back-off position? 脱扣位置在哪 5207.Plu

24、g the well for side tracking. 打水泥塞侧钻五、五、ABNORMAL WELL CONDITION AND WELL CONTROL 异常井况与压井异常井况与压井168.The mud is gas out. 泥浆有气侵 169.The pit has lowered quickly. 泥浆池液面下降很快 170.The hole lost returns. 井口不返泥浆 171.The returns are unstable. 返出泥浆量忽大忽小 172.Wheres the thief zone? 漏失层在哪里 173.Cut down the flow ra

25、te. 降低排量 174.Lower the mud density. 降低比重 175.Cut down the hydrostatic pressure. 减少静压 176.The gas smell is strong. 天然气味度很浓 177.Theres some trace of oil. 发现有油花 178.The pump pressure is fluctuating. 泵压不稳 179.It is a zone of abnormal pressure. 这是异常压力层 180.The hole (well) is kicking! 井涌啦! 181.Shut in the

26、 BOP! 关闭防喷器 182.Sound the general alarm quickly! 快发出综合警报 183.The stand pipe pressure is 10 kg/cm2. 立管压力 10 公斤/厘米2 184.The casing pressure is 25 kg/cm2. 套压 2510 公斤/厘米2 185.Fill out the kill sheet. 填写压井记录表 186.Kill the well. 压井 187.Theres a combination of lost returns and the kick. 又喷又漏, 情况复杂 188.Reve

27、rse the gas out of the hole. 反循环排气 189.Whats the lag time? 迟到时间是多少 190.The well is now stable. 现在井眼已经稳定六、六、PREPERATIONPREPERATION BEFOREBEFORE MAKINGMAKING HOLEHOLE 钻前准备钻前准备191.Tell the mechanic to check the motor torque . 让机械师检查马达扭矩。192.Electrician must care of the electric cable moving whit derric

28、k.电工注意照管好移动电缆。193.Speed up. Please! 请快点干！194.Have you fixed the derrick substructure in position? 井架底座固定好没有？195.Get all the drilling tools unlashed.解开所有钻具。196.Put the ramp back onto the Vdoor 将坡板吊回到井架大门上。197.Put the rathole scabbard back in place.安放大鼠洞。198.Connect the Kelly spinner to the Kelly.连接动力

29、短节和方钻杆199.Connect the feeling plate to the drill collars.用钻铤连接探深板。200.Have you checked all the equipments? 设备都检查过了吗？201.Weve checked them, no problems in running.检查过了，运转是没有问题了。202.How much high viscosity mud have you mixed? 高粘度泥浆配备了多少？203.About 160 cubic meters.大约 160 方。204.Please pick up the 171/2

30、bit and 36 hole opener to the floor.请将这个 171/2钻头和 36扩大器吊上钻台。6205.The distance between feeling plate and rotary table is 70 meters.探测海底到转盘面的深度是 72 米。七、七、INSTALLATION OF WELL HEAD ASSEMBLY AND PRESSURE TEST 井口安装及测试井口安装及测试206.Cut off the 30conductor with the corch.用气焊割掉 30隔水管。207.Weld on the 30bottom f

31、lange.焊接 30的底法兰。208.Hoist and rig up the 30 Tee.吊装 30三通。209.Connect the 12 pneumatic valve and the flow line.连接 12气阀及管线。210.Hoist and nipple up the 30diverter.吊装 30转喷器。211.Have the 30diverter pressure-tested with 1000psi.30转喷器试压 1000 磅/英寸2。212.Rig up the 135/8 BOP stack onto the well head.将 135/8防喷器

32、组移到井口。213.This gasket ring cant be used any more. Change to a new one, please.这个钢圈不能用了，换个新的。214.Tighten up the well-head guy-lines a bit-more.井口绷绳绷紧一些。215.Change the 5 pipe rams to 31/2 rams.把这个 5闸板换成 31/2的。216.Have the HYDRIL annular preventer pressure-tested to 5,000psi.海德里环形防喷器试压 5000 磅/英寸2。217.H

33、ave the BOP pressure-tested with 10,000psi.防喷器试压 1000 磅/英寸2。218.Hold each pressure test for 10 minutes.每次试验稳压 10 分钟。219.The pressure test is O.K.试压合格。220.Have each valve of the stand-pipe manifold pressure-tested to 5.000psi.立管闸门逐个试压 5000 磅/英寸2。221.Mud pumps arent allowed to be used for the test if

34、the pressure is over 3000psi.超过 000磅/英寸2的不允许直接用泥浆泵试压。222.Run the wear bushing.下抗磨补心。223.Adjust the manifold pressure to 1500psi.管汇压力调到 1500 磅/英寸2。224.Adjust the HYDRIL (annular preventer ) pressure to 900 psi.环形防喷器压力调到 900 磅/英寸2。225.Close the blind ram, please.请关上防喷器盲板。226.Open the pipe ram, please.

35、 请打开闸板防喷器。227.Check the pre-charged pressure of the accumulator.检查储能器预压。228.The accumulator pressure of the Koomey Unit is 3,000psi.库美系统储能压力 3000 磅/英寸2。八、八、BOTTOM HOLE ASSEMBLY 井下钻具组合井下钻具组合229.Get a 121/4 Smith bit ready.准备一个 121/4史密斯钻头。230.Dont forget to put the TOTCO support ring in the bit sub (f

36、or the deviation survey tool.)别忘了在钻头接头内安放测斜承托环。231.The thread type of the bit is 6 5/8 regular pin.钻头的扣型是 6 5/8正规公扣。232.Whats the make-up torque required for the bit?钻头上扣力矩要多大？233.Run in two stands of 9 drill collars.下两根 9钻铤。234.Set the make-up torque of 9 DC to 10000 kg-meter.9钻铤上扣力矩要调到 10000 公斤7米。

37、235.The cathead cant give enough torque, so we have to use a snatch block.猫头力量不够，要挂上滑轮。236.Connect the 731630 crossover sub.接上 731630 的配合接头。237.A 12 1/4 stabilizer is needed to be connected here.这个地方要接个 12 1/4的扶正器。238.This is a 7 3/4 flexible sub.这是 7 3/4挠性短节。239.Put the 8 jar on to the flexible sub

38、.在挠性短节上接上 8震击器。240.A function test must be made before the jar is run in the hole.下震击器时，要做性能试验。241.Make up 15 joints of 5 HW Drill pipe.接上 15 根 5加重钻杆。242.The DIV (drop in valve) has to be put on top of the bottom two joints of HWDP.投入式止回阀安在下两根加重钻杆的上面。243.This is the BHAbottom hole assembly log.这是井下钻

39、具组合的记录本。244.Make sure you record all outside and inside diameters and lengths in the log 一定要把所有的内外径和长度记好。245.We need a short drill collar to put here.这里要接一根短钻铤。246.Whet is the BHA of this well.这口井的钻具结构是什么？247.This is the hole geometry of this well.这是这口井的井身结构。248.The thread type of 9DS is 75/8Regregu

40、lar.9钻铤的扣型是 75/8正规。九、九、OPERATING 操操 作作249.Latch the elevator.扣吊卡。250.Unlatch the elevator.开吊卡。251.Set the slips around the pipe.放卡瓦。252.Pull out the slips.提卡瓦。253.Put out the slips.打大钳。254.Adjust the crown-o-matic.调整防碰天车。255.Put the Kelly into the rat-hole.方钻杆进鼠洞。256.Lock the hook pin.锁紧大钩销子。257. Pu

41、ll the cat line.拉猫头。258.Unlock the hook.打开大钩。259.Operate the brake lever.扶刹把。260.Stop the pumps for a flow check.停泵观察。261.Make a wiper trip to the 20casing shoe.通井到 20套管鞋。262.Ream down all the tight points.在所有遇阻点进行划眼。263.Work the string up and down.上下活动钻具。264.Run in the turbine drill.下涡轮钻具。265.Rever

42、se out the drill pipe.反循环清洗钻杆。266.Make a short trip.进行短起下钻。267.Change the cutters of the hole opener.更换扩大器的牙轮。268.Slug the pipe.灌重泥浆。269.Drill the Kelly down.钻完方钻杆。270.Circulate bottoms up for a sample.循环取样观察。271.Circulate the hole clean.循环清洗井眼。272.Have it greased.打黄油。8273.Change the Zinc block of c

43、athode Protection.换阴极保护用的锌棒。274.Give me a spanner ,please.请给我拿一个扳手来。275.We need a 48pipe wrench.要一把 48的管钳。276.Change the chain tong with a bigger one.换一把大链钳。277.Strike it with a sledge hammer.用大锤打。278.We want a triangle file.要一把三角锉刀。279.Tighten up the screw.紧一下螺丝。280.Change the jaw assembly on the b

44、reak out tong.换钳头。281.Give me a hand, please.请帮下忙。282.Check it with a level.用水平尺测量一下。283.Change the chain for the made up cathead.换一根猫头链子。284.Put some engine oil on it.抹点机油。285.Do you understand?明白吗？286.Start the shale shaker.启动振动筛。287.Start the desanders and desilters.开除砂器、除泥器。288.Shut off the dega

45、sser.关除气器。289.Pick up the drill pipes on the cat walk ramp .把这几根钻杆拉到坡道上。290.Connect the rotary hose to the swivel.接单根要快。291.Make a faster connection, please !接水龙带!292.Lay down the pipe.甩单根。293.Set and secure the safety clamps on the drill collars.给钻铤卡上安全卡瓦。294.Stab the pipe with the hydraulic arm.用液

46、压钳扣住钻杆。295.Disconnect it with a chain tong.用链钳卸开。十、TRIPPING 起下钻起下钻296.After tripping the string out of the hole.起完这趟钻，用一个硬一点的休斯钻头更换磨钝的钻头。297.Connect the junk sub.接上打捞杯。298.Check the bit O.D. with a bit gauge.拿钻头规来量一下钻头外径。299.When the bit goes through the BOP, slow down, please!当钻头通过防喷器时，慢一点放。300.Thi

47、s is the dope for drill pipe thread. It cant be used for drill collar.这是钻杆丝扣油，不能用在钻铤丝扣上。301.2,500 kilos- meter torque is enough for making-up E Grade drill pipe. E 级钻杆上扣力矩用到 2500 公斤米就可以了。302.Put a protector on each of 5drill pipe.每柱 5钻杆上加一个护箍。303.Please engage the eddy current brake.请挂上涡磁刹车。304.Can

48、we use the power slips?可以使用气动卡瓦吗305.Dont set the slips too low on the pipe! 卡瓦不要卡太低了。306.No way, the tong angle is too small! 不行，大钳的角度太小了。307.The holes tight. Dont snub the string. 遇阻了，不要强下。 308.Monitor the returns the trip tank while running in.下钻时返出泥浆要记录。309.Stop circulating! 停止循环泥浆。310.Drop the T

49、OTCO survey tool.投“陶特”测斜仪。311.Break out the Kelly and set it back in the rat-hole.卸方钻杆并放进鼠洞。9312.Slug the pipe with two cubic meters of mud before pulling out.起钻前打 2 方重泥浆。313.Can we break out the pipe with rotary table? 可用转盘卸扣吗？314.No! Break it out with both sets of tongs. 不行，要用大钳卸扣。315.Spin it out

50、with the air spinner. 用气动扳手卸扣。316.Put the pipe wipers on the string.装上胶皮刮泥器。317.Tale down the volume while filling the hole.灌满泥浆，并且要计量。318.If the string is not very heavy, the top gear can be used to pull it out.钻具轻可以用高速挡起。319.Dont set this stand back.这柱钻杆不要放在钻杆盒上。320.Lay down this bent drill pipe.

51、甩掉这根弯钻杆。321.Make up the lift sub. 接好提升短节。322.Secure the safety clamp.上紧安全卡瓦。323.Rack back the drill-collars onto the finger board.钻铤靠在指梁上。324.The bit is nearing the shoe. Slow down the running speed.快到套管鞋位置了，放慢点速度。325.This is the under gauged interval.这是缩径井段。十一、十一、 DRILLING 钻钻 井井326.This is the dril

52、ling programmer of CFD18-1-1 WELL.这是 CFD18-1-1 井的钻研井设计书。327.The proposed total depth of this well is 3,900 meters.这口井的设计井深是 3900 米。328.How much WOB weight on bit is required? 要加多少钻压？329.Keep the rotary speed at 120-140 PRM and the flow rate at 3,000LPMliters per minute.转速保持 120-140 转/分，排量 3000 升/分。3

53、30.The pump pressure is too high！泵压太高了！331.Make up the Kelly and circulate bottoms up.接方钻杆循环泥浆。332.Dont ream the hole too fast.划眼不要太快。333.Slow RPM and light WOB are needed in drilling with a new bit at the beginning.钻头使用初期要慢点转达。334.Bring the RPM up slowly.逐步提高转速。335.Get yourself attentive and carefu

54、l in the operation.精心操作。336.Avoid the brake-slipping or the string dropping when feeding off while drilling.在钻进过程中防止溜钻、顿钻。337.Keep steady pressure on the brake to feed off smoothly.操作要平稳，做到均匀送钻。338.Keep an eye on the rotary torque.注意观察转盘扭矩变化。339.The penetration rate is getting slower.钻时变慢了。340.The b

55、it must have been balled up, mustnt it? 钻头泥包了，是吗？341.Has the bit got dull? 是钻头磨秃了吗？342.The bit has been used too long and is nearly worn out.钻头已到期后期，快磨坏了。343.The bit is dull, so well have to pull it out to change to a new one.钻头不行了，应该起钻换钻头。344.The pump pressure has increased. One nozzle may be plugg

56、ed.泵压升高。可能有个水眼堵了。345.Stop drilling at 2,965 meters.钻至 2965 米，停钻。346.Get ready to drop a TOTCO (deviation survey ) one the circulation has finished.循环结束，10准备投测。347.How long is it circulate bottoms up? 需要循环多长时间？348.Circulate for one and a half hours and then pull the string out at 14:30.循环一个半钟头，14:30

57、起钻。349.How long has this bit been used? 这个钻头使用了多长时间？350.This bit has been used for 25 hours and 15 minutes.使用了 25 小时 15 分钟。351.This bit has drilled 156 meters of hole.这个钻头进尺 156 米。352.The penetration rate has been 6.18 meters per hour.机械钻速 6.18 米/时。353.This interval of the well is liable to deviate.

58、这个井段是易斜地层。354.There should be some changes to the drilling parameters.要改变一下钻井参数。355.The dog-leg severity of this well is not very big.这口井的狗腿变化不大。356.What was the deviation indication of the last survey? 上次测多少度？357.The surveyed deviation was 2.5 degrees at 2,900 meters.在 2900 米处是 2.5 度.358.How much K

59、elly is out when the bit was at the bottom of the hole? 钻头到底时的方余是多少？359.Measure the Kelly-down before you are going to trip.起钻前量一下方入。360.What will the bit depth be when this joint of pipe goes through the table? 打完这根单根井深是多少？361.What is the hook load at the time of pulling out? 起钻时悬重是多少？362.Whats the

60、 pick-up weight? 上提重量是多少？363.Whats the lowering weight? 下放重量是多少？364.Theres no need to connect this joint.这个单根不要接了。365.The well is going to be completed at 3,920 meters.钻至 3920 米完钻。366.Whats the hook load when the HWDP is completely run in the hole.下完加重钻杆后的悬重是多少 367.High pump pressure and reduction i