100T汽车吊性能表

1、100T主要性能与参数100T主要性能与参数项目数值最大额定总起重量100000 kg基本臂最大起重力矩3238kN.m最长主臂+副臂最大起重力矩1127kN.m主臂最大起升高度48m主臂+副臂最大起升高度62.1m外形尺寸（长X宽X高）14550 X 2750X 3750mm主臂长12.8-48m副臂长18.1m100T主要性能与参数起重特性表PAT工作幅度WORKINGRADIUS(m)ED LIFTING CAPACITY TABLE主臂BOOM支腿全伸、后方、侧方作业REAR&SIDE WORKING AREA WITH OUTRIGGER FULLYEXTENDED单位（主臂

2、仰角BOOMANGLEC）JNIT ): Kg主臂+副臂45+9.5mBOOM+JIB45+16.0m臂长BOOM LENGTH副臂安装角JIB OFFSET副臂安装角JIB OFFSET12. 0m16. 2m20. 4m27. 0m33. 0m39. 0m45. 0m5305303.0100000700008060002500400013003.59200070000580007855002400360012004.08500070000540007650002300320011504.5760006400051000350007445002200300011005.07000058000

3、49000350007240002100270010505.563000510004500035000260007037002050250010006.05700046000430003400026000683400195024009506.5480004300041000330002600020000663200190022009007.0440004000039000320002600020000642900185021008507.537000370003500030500250002000015000622400180018008008.034000340003200029000400

4、01900015000602000175015007509.0270002700027000250002250017500150005816001500120070010.02190021900022000205001650015000561400135011.018400190001950018000155001400012.015700160001650016000145001360014.01160001280013500130001200016.08400980010500110001050018.06300780082008500900020.0600066007200750022.

5、0500052005800620024.042004800520026.03800430028.03100360030.02900说明(NOTE ):以上作业工况均为支腿全伸，不允许在不打支腿的情况下吊重。(Above working condition is all withoutrigger fully extended,never lift a load on the wheels.)表中粗线以上数值是由起重机的结构强度所决定的，粗线以下数值是由起重机整机稳定性所决定的。(Capacities above the thick line in the table are based on

6、the boom strength,the others,on stablitiy of the complete machine.)打好第五支腿时，表中数值适用于圆周360(With the 5th outrigger fully extended,full100T主要性能与参数360rotation is available according to the values listed in the above table.)表中所列额定起重量为最大允许值，并包括吊钩重量(100吨吊钩重815Kg, 60吨吊钩重560Kg, 6吨吊钩重180Kg)和其他吊具的重量。(The rated l

7、ifting capacity listed in the table ismax.allowed value,including weight of thehookblock (thehookblockweight is815kg for100t,560kg for60t,180kg for6t)and otherslings.)表中所给幅度值，是指吊载后吊钩中心到回转中心的水平距离。(A working radius given in the tableis a horizontal to the axis of the slewing ring when the hookblock is loaded.)当实际臂长和工作幅度在两数值之间时，应按最大臂长和幅度值确定起重量。(When actual boomlength is between two values,determing lifting capacity according to bigger boomand radius.)在副臂伸出的情况下使用主臂作业时，额定起重量不仅要扣除吊具的重量，还要