船舶材料验证试验报告范本

1、船舶材料验证试验报告Verificati on Test Report of Shipp ingMaterial报告编号：JX20101-2发送日期：2010年1月10日产品名称：JXM402埋弧焊丝验证主管部门：“ ABS ”美国船级社产品牛产企业：宜兴金兴焊接材料有限公司Report number: JX20101-1Delivery date: Jan. 10th, 2010Product name: JXM402 submerged arc weldi ng wiresCompete nt departme nt of verificatio n: “ ABS ” America n

2、Bureau ofShippi ngProduct Manufacturing Enterprise： Yixing Jinxing Welding MaterialCo.,Ltd.宜兴金兴焊接材料有限公司Y ixi ngJinxing Weldi ng Material Co., Ltd.船舶焊接材料验证试验报告Verificati on Test Report of Weldi ng Material for Shippi ng（一）、材料名称：埋弧焊丝（二八牌号H08MnA工厂牌号 JXM-402（三）、试品规格5.0 mm 批号：090585（四）生产企业：宜兴金兴焊接材料有限公司（五

3、）、认可级别：3M级1. n ame of material: submerged arc weldi ng wires2. product grade H08M nAfactory grade JXM-4023. sample size 5.0 mm lot No.: 0905854. Manufacturer: Yixing Jinxing Welding Material Co., Ltd.5. recog niti on level: class 3M（六）试验内容：6. content of the test序号No.试验项目Test item引用标准Refere need sta

4、ndard1自动焊熔敷金属力学性能试验Mecha ni cal property testi ng of deposited metal of automatic weld ingGB/T8110-20082自动焊对接接头力学性能试验Mecha ni cal property test of butt joint ofGB/T8110-2008automatic weldi ng3焊丝及熔敷金属化学成份分析Chemical composition analysis testing of weld ing wires and deposited metalGB/T14957-944焊丝镀铜层厚度

5、及表面质量检查Inspection of copper-plating thickness and surface quality of weldi ng wiresGB/T14957-94（七）试验结果分析：1、焊接试板编号及探伤结果见表（一）7. testi ng result an alysis:1. the nu mber of testi ng plates and the result of flaw detect ion see table 1表（一）table 1编号No.牌号及材质Grade&material焊丝直径Diameter of weld ing wire试板焊接

6、方式Weldi ng type of sample合格标准 accepta nee criteria测试结果Test resultJXM09-11MJXM-402 5.0 mm熔敷金属Deposited metalGB/T3323-87U级合格QualifiedJXM09-12MH08 MnA 5.0 mm平对接Downhand joi ntGB/T3323-87 Class n合格Qualified2、焊接及熔敷化学成份见表（二）2. Chemical compositi on of weld ing and depositi on see table 2表（二）Table 2名称NameC

7、SSiPMnCu备注Note焊丝Weldi ng wires0.070.0120.030.0160.960.15标准要求sta ndards 0.10 0.030 0.07 0.030 0.20熔敷金属Deposited metal0.070.0120.430.0181.480.10由表可知化学成份符合 及标准This table show that the chemical composition meet standards GB223.1-223.70 and AWS .A. 5.183、熔敷金属力学性能试验结果见表（三）3. Test ing result of mecha ni ca

8、l property of deposited metal see table 3表（三）Table 3试件编号Sample No.屈服强 度Yield stre ngth MPa抗拉强度Ten sile stre ngthMPa伸长率% elon gati on%夏比V型缺口冲击 试验（-20C） JSharpy V-no tch impact test （-20C） J平均值AverageJXM09-11M44559528140、120、150136标准要求Sta ndards三305400-560三22三34由表（三）可知熔敷金属力学性能符合 GB2552及标准。table 3 show

9、s that mechanical property of deposited metal meet standards GB2552 and AWS .A. 5.18.4、对接接头力学性能试验结果见表（四）4. Testi ng result of mecha ni cal property of butt joint see table 4表（四）Table 4编号No.抗拉强度Ten sile stre ngthMPa冷弯：32、120 Cold bending: 32, 120夏比V型缺 口冲击试验（-20C） JSharpy V-notch impact test （-20C） J平

10、均值Average正弯Positively bending反弯Reverse bendingJXM09-12M505合格qualified合格qualified137、140、141139标准要求Sta ndards三400受拉面上出现的裂纹或 其它缺陷长度不得 大于3 mmThe len gth of cracks or other defects on the surface of tension face should be not more tha n 3 mm三34由表（四）可知熔敷金属（貌似应该是对接接头）力学性能符合GB2650及AWS.A.5.18 标准。Table 4 sho

11、ws that mecha ni cal property of butt weld ing joi nt meet sta ndards GB2650 and AWS .A. 5.18.5、焊丝铜层厚度及表面质量见表（五）Copper-plat ing thick ness and surface quality of weld ing wires see table 5表（五）Table 5焊丝批号Wire lot No.镀层厚度Plat ing thick ness色泽Colour and lustre线径Diameter排列Placeme nt备注Note0905850. 03 mm表

12、面光滑色 泽一致Smooth surface and same colour 4.95 mm整齐规范头 尾清析Neat and clear head & tail由表(五)可见焊丝外观质量符合GB/T14957-94标准。Table 5 shows that the presentation quality of welding wires meet standards GB/T14957-94.验证试验结论：宜兴金兴焊接材料有限公司生产“ JXM ”埋弧焊丝按照美国及国标GB/T8110-2008的3M级验证结论如下：1、 自动焊熔敷金属及对接接头力学性能符合3M级规范要求。2、焊丝化学成份

13、及表面质量符合 GB/T14957-94要求。Conclusion of verification test:JXM ” submerged arc welding wires produced by Yixing Jinxing Welding Material Co., Ltd. are tested accordi ng to the requireme nts of AWS.A5.18(America n) and 3M class of GB/T8110-2008, the conclusions are as follow:1. Mechanical property of butt welding joint and deposited metal of automatic weldi ng meet the requireme nts of 3M class.2. Chemical comp