如何设置BIOS从光驱启动

1、设置从光驱启动：一、进入BIOS的方法根据BIOS的类型也有所不同，最常用的就是开机一直按住 Del”键直到进入的BIOS，界面大多如右图:移动f JJ t光标键可以进行 选择，一般设置开机启动顺序的项目就在 Advaneed BIOSFeatures "这个选项中（右图红 框）。FriP/PcI configurationsLoad Fail-safe DefaultsTimejratej Hard Disk Type.Load optimized DefaultsAdvanced BIOS FeaturesHeal th st at uspower HanagsetupCMOS

2、setup utilitycopyri&ht(c)1984-2001 Award softwareset supervisor passwordExit without savingset ustr passwrd$旳令 & Exit setup回车后就会出现下面的画面:Adxnced chipsFeaturesAnti-Virur ProtectionDi-abl'sdCFU Internal CacheEnabledItem HelpEirternil CcheEii iblrdCPU L? Cache ECC CheckEn.-ibl rdMenuLevelPro

3、cefcr Nu*ber FeatureEnablrd上图方框内的四条分Quick PostDisabledAl lows you to chooseQuick Power On Self TestErtat' H dthe VIRUS warning别为第一、第二、第三、Fitt Boot DeviceFhppyfeature for IDE HardSrond Poet T'flvi caHDD-Q1Disk boot sector其他启动顺序，如果设Third Boot DeviceLS12Gprotection If thisBoot Other DeviceEnabl

4、functicn is enabled置光驱为第一启动顺Swap Floppy triveKnablcdand some one at t enp t toBoot Up Floppy S«elrEtiabl rdwrite njata into this序的话，可以移动光标Boot Up NwnLock St at usONarea, BIOS will showGate A2D OptionFata warning message on到 First BootTypematic Rate SettingDisabledscreen and jlarm beepTypfilial：

5、 xc Rii<3叮二点r6Drive ”，然后回车，用ypeinat it* Ka+r (血*£50Security Opt ionSft i.irf J光标选择OS Select For DRAM > 641TNon-0S2HDD Inst ant RecoveryDisabledCDROM ”，然后回车确定即可。按F10保存，然后按ESC键退出（可能提示存盘，按“ Y”退出就行。）二、还有一种按 Del”进入BIOS的界面如下:这种BIOS界面相对比较老一些，但也很常见，设置从光驱启动时可以选择Guxlnr Soft/hunehanq. ye«ih.ric

6、t> CMOS SETUP UIILITV AVftHD SOFIW口HE. INC,BIOS FEATURES SETUP ”并回车，在接下的界面中选择Boot Sequenee ”，用f光标键将顺序调整为CDROM , C, AHOM PCI/ISA BIOS BIOS FEATURES SETUP WARD SOFTVAM . INC,GaoYin SoftCPU In t er nd 1 Cort SpeedBoot Virus DeltectionCPU Level 1 Cec局CPU Level 2 CacheCPU Level ? Cdcl ECC CheckDisable

7、d Hdbl+'d rtdbled EhdbledBIOS Upda1«Turbo HodeQuick Power On Self (est HDD SftaiMnc* SCSI/IDE First:F ndbid :Disabled :Lrvdblcd:IDEPCl/VCn Palette ROH BIOS CBFFF CFFFf D3fH MFI -DBFFF -DFFFFVideoC890OCCO0Ooeoeo0406908000PCOO0SnoopShtido*ShBrlowShddoNShadowShodotffShadowSEukdoM StatusDisable

8、d:En.ib :r n<ib :En(ib :Endb :En<ib :ndb :I n<ib :On :DisabledcdBoot Sequence: CDROHPCTflBoot Up F OPPV Seek: E DfibedFloppy Disk Access Control : R/WIDE HDD Block Mode Sectors : Disabled Hl)() S.H.R. R. T. cdpubi 11: Enabled PS/2 Housa Fund ion Control: AutoOS/? Onbotird Heworv > 64H: D

9、i sob 1Boot Up NunLck 让 Rate SettingTpendt ic Rdte (Chur/Sec): 6 TvPMcit ic Del up (Hcsc): 250Secur 1Opt ion: Seh»pESC : QuitTl* i Select ItemFl : HelpPU/PD/*/- : HodiFvF5 : Old Values (Shift)F2 : Color f6: Lorid DIOSJ I ; Loadb按F10保存退出。BIOS SETUP UTtLJTVAdvancedFwerBootSecurityExit備IK? Persian

10、 :(MLOO.OBIOS Build De.te :08zl4/63System tlowtry；1GAHJII ：S7：利Syten DdtECUed 05/23吃005】 *Select ScreentiTvr led I trn+Change FieldUbSrlcrt Fie IdFlGerterdl Helpfialifi ur: and Ek itESCExit(CjCnpyTighit 1出片 烦El.Mir?jEi|：代tm马" QiCr三、还有一种 进入BIOS的 方法就是开机 按“F2”键， 通常BIOS内 容是菜单式 的。如下图设置光驱启动时，移动选择菜单到“ BOO”菜单，如下图:SETUP UTtLJTVMali】 Adwmued