网络摄像头说明书

1、Table of ContentsIntroduction1Power Supply to the IP Camera1iOS Mode (for iPhone / iPad)2First Time Settings or Changing to a New Wi-Fi Router2Adding Second iOS Device to Existing IP Camera Connection61. Under Wi-Fi environment which has completed first time settings62. Outside of Wi-Fi environment

2、which has been set9Introduction of App Interface101. Live Monitoring Page102. Settings Page113. Basic Setting114. Advanced Settings12Android Mode (for Android O/S Devices)13First Time Settings or Changing to a New Wi-Fi Router13Adding Second Android Device to Existing IP Camera Connection171. Under

3、Wi-Fi environment which has completed first time settings172. Outside of Wi-Fi environment which has been set21Introduction of App Interface221. Live Monitoring Page222. Setting Page23Specifications25SpeakerIntroductionLED IndicatorNight Vision LEDsUSB PortResetmicroSDCard SlotMicrophoneLens Power S

4、upply to the IP Camera1.Connect the USB cable between USB port and the included AC adaptor.2.Connect the AC adaptor to the power source.iOS Mode (for iPhone / iPad)NOTE: The O/S version of the iPhone or iPad must be iOS5.0 or later.First Time Settings or Changing to a New Wi-Fi RouterSTEP 1After the

5、 IP camera is connected to the power source, please wait for approx. one minute until the blue LED indicator starts flashing. If the blue LED indicator is not flashing, the IP camera will need to be reset. Please use a pin to stick into the RESET hole on the back side of the IP camera and hold for a

6、round 10 seconds and then release. The IP camera will restart.STEP 2Install the App named “GuardPro” from App Store.NOTE: If you have purchased this IP camera bundled with JAY-tech Tablet PC series, this App may have already been pre-installed and the Apps name is “GuardPro”. Thus you can skip this

7、step.STEP 3Go to “Settings” of the Apple Device and select “MyAPxxxx” from the available Wi-Fi AP list.After the Apple Device is successfully connected to that Wi-Fi AP, will appear.STEP 4Enter the App, press “+” and select “Setup Camera”.STEP 5Follow the instructions to complete the setup for the c

8、onnection between the IP camera and the preferred Wi-Fi network:A: click “ YES” to search Camera B: Input your WIFI password C: Searching camera D: You can change password. STEP 6When above steps are completed, please press the play button to start the live monitoring. If you cannot see the live mon

9、itoring screen, please close the App and re-enter the App again.NOTE: The above steps are the connection method for a new product.If you want to move your IP Camera to another Wi-Fi environment, or yourWi-Fi router has been modified; you need to RESETthe camera first to clear all the previous connec

10、tion information and then repeat the above steps.Adding Second iOS Device to Existing IP Camera Connection1. Under Wi-Fi environment which has completed first time settingsTo add second iOS device to the IP camera(s) connection under Wi-Fi environment which already successfully completed first time

11、settings, please follow the procedures below.Add by QR code:Enter the App and press“+”.Select “Connect Camera”.Select “Scan QR Code”.Scan the QR code on the back of IP camera.UID number of IP camera will display here. Press“Add” to connect.Default password is “admin” if required.NOTE: If you changed

12、 the password during your fist time connection, you need to enter your amended passwordAdd by LAN search:Enter the App and press “+”.Press“Search”icon.The App will detect the connected IP camera(s) automatically.Select “Add By Lan Search”.UID number(s) of the detected IP camera(s) will be displayed

13、here.Select the UID number you would like to connect to.Press “Add” to connect.2. Outside of Wi-Fi environment which has been setEnter the App and goes to “Settings” page.You may create a QR code as instructed below for another iOS device from outside of the Wi-Fi environment which has been set.Sele

14、ct “Share Camera QRCode”.Save the QR code and provide to whom would like to join.Proceed “Scan by QR code” to log in.QR code will appear here.Introduction of App Interface1. Live Monitoring PageSelect the video size:SD Video: 480pHD video: 720pSettingsVideo playbackTwo-way audioVideo recordingSnapsh

15、ot2. Settings Page3. Basic SettingRename the IP camera.Reset your password for IP Camera.(Default password is “admin”)4. Advanced SettingsSet the recording mode (No Record / Full Time Record/Alarm Trigger Record).Set the alarm type of motion detection.Set the sensitivity of motion detection.Check th

16、e available space of the memory card or format the memory card.If it is set at on, the date and time will be shown on the live monitoring page.Set your Environment Mode (frequency).Select the angles of the video.Adjust the sound volume of the built-in microphone.Adjust the sound volume of the built-

17、in speaker.Select your preferred time zone.Android Mode (for Android O/S Devices)NOTE: The O/S version of the Android device must be Android 4.2 or later.First Time Settings or Changing to a New Wi-Fi RouterSTEP 1After the IP camera is connected to the power source, please wait for approx. one minut

18、e until the blue LED indicator starts flashing. If the blue LED indicator is not flashing, the IP camera will need to be reset. Please use a pin to stick into the RESET hole on the back side of the IP camera and hold for around 10 seconds and then release. The IP camera will restart.STEP 2Install th

19、e App named “GuardPro” from Play Store.NOTE: If you have purchased this IP camera bundled with JAY-tech Tablet PC series, this App may have already been pre-installed and the Apps name is “GuardPro”. Thus you can skip this step.STEP 3Enter the App, press “+” and select “Setup new camera”. Click to a

20、dd new camera Choose “ Setup Camera” STEP 4A: Choose “ YES” to search Camera B: Fill in the WIFI Password which your Android device be connectedC: Connecting NOTE: The connection will fail if the password is entered wrong. Thus to reset the camera may be required (please refer to STEP 1).STEP 5In th

21、e following “Device Settings” interface, you may change the “Name” of IP camera.Or press “Add” to skip without any change and finish the camera settings.Default password is “admin” and you can change it later in setting page.NOTE:You can change the name of IP camera ONLY in this step. STEP 6When abo

22、ve steps are completed, please press the play button to start the live monitoring. If you cannot see the live monitoring screen, please close the App and re-enter the App again.NOTE: The above steps are the connection method for a new IP camera.If you want to move your IP Camera to another Wi-Fi env

23、ironment, or yourWi-Fi router has been modified, you need to RESET the camera first to clearall the previous connection information and then repeat the above steps.Adding Second Android Device to Existing IP Camera Connection1. Under Wi-Fi environment which has completed first time settingsTo add se

24、cond Android device to the IP camera(s) connection under Wi-Fi environment which already successfully completed first time settings, please follow the procedures below.Add by scan QR code:Select “Connect camera”.Enter the App and press“+”. Select “Scan QR”.Scan the QR code on the back of IP camera.I

25、D number of IP camera will display here. Press “OK” to connect.Add by Wi-Fi search:Select “Connect camera”.Enter the App and press“+”. Select “Wifi Search”.ID number(s) of the detected IP camera(s) will be displayed here.Select the UID number you would like to connect to.Press “OK” to connect.2. Out

26、side of Wi-Fi environment which has been setYou may add another Android device from outside of the Wi-Fi environment which has been set.Enter the App and press“+”.Select “Connect camera”. Enter your password for IP camera.Default password is “admin”.NOTE: If you changed the password during your fist

27、 time connection, you need to enter your amended passwordEnter 20-digit ID number which is available on the bottom of the IP camera.Introduction of App Interface1. Live Monitoring PageSnapshotTwo-way audioVideo recordingSettingsSelect the video size:SD Video: 480pHD video: 720pVideo playbackSD VIDEO

28、2. Setting PagePress and start setting.Set the sensitivity of motion detection(frequency)monitoring page.Set the angles of your video.Set your Environment mode (frequency).If this is set at on, the date and time will be shown on the live monitoring page.Reset your password.(Default password is “admi

29、n”)Format the memory card.Set the recording mode.(Off / Record All Day/ Record Alarm)Adjust the sound volume of the built-in microphone and built-in speaker.Information of the memory cardInformation of the IP cameraSpecificationsImage SensorCMOSLens TypeFixed focusApertureF/2.5Effective Focal Length

30、f =3.6mmExposureAutoViewing Angle110°IR LED (Night Vision)YesExternal Memory StoragemicroSD up to 32 GBWi-FiIEEE 802.11b/g/nVideo Size720p / 480pFile FormatsVideo: MP4(H.264) / Photo: JPGReal Time ClockYesTwo-Way AudioYesPower Supply5 V / 1.0 AMotion DetectionYes (by App)Supported iOS VersioniO

31、S5.0 or laterSupported AndroidVersionAndroid 4.2 or laterDimensions111 x 68 x 32 mmWeightApprox. 0.128kgs*Above specifications are subject to change without prior notice.Service ProcedureIf you have reason for complaint, or your device is defective, please contact your dealer or the service division

32、 of JAY-tech GmbH to make arrangements for service procedures.Service Hours:Monday - Thursday from 8:00 am to 5:00 pmFriday from 8:00 am to 2:00 pm.Phone No.:02161 / 5758950Email:infojay-tech.dePlease do not send your product to our address unless requested to do so by our service team. All costs an

33、d the risk of loss are the responsibility of the sender.We reserve the right to reject unrequested deliveries, or return the package at the senders expense.EC Declaration of ConformityThe product complies with the protective requirements of European Directive 1999/5/EC (R&TTE).The conformity dec

34、laration for this product is available under www.jay-tech.de.Directive 2012/19/EC on Waste Electrical and Electronic Equipment (WEEE)This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your ho

35、usehold waste. There are separate collection systems for recycling in the EU. For more information, please contact the local authority or your retailer where you purchased the product.IntendedUseThis camera is used to monitor and turn your smartphone or tablet PC into a monitoring center. The camera

36、 can be used universally and controlled remotely. The operation can be performed directly via a wireless network over a wireless LAN. In addition, this camera provides remote access via the web browser. The power supply of the camera is supplied with 230V mains voltage. The camera and AC adapter are

37、 only suitable to be used indoors.Any other usage other than specified is not permitted. Changes can cause damage and risks, such as fire, short circuit, electric shock, etc.For all damages that are resulted from improper use, the operator shall be responsible.Warnings and Safetyl Please read the manual before using this product.l Since this product is not waterproof