五金工具中英文对照

1、两用扳手套装COMBINATION SPANNER SET 加长型两用扳手COMBINATION SPANNER EXTRA LONG 梅花棘轮开口扳手OPEN ENDED SPANNER WITH RING RATCHET 梅花棘轮开口扳手套装OPEN ENDED SPANNER WITH RING RATCHET SET 两用棘轮扳手COMBINATION RATCHET SPANNER 两用棘轮扳手套装COMBINATION RATCHET SPANNER SET 1/4'连接物ADAPTOR 1/4' 组合支架工具COMBINATION HOLDING TOOL 小型发

2、光二极管MINIATURE LED LAMP 活动扳手SINGLE OPEN ENDED SPANNER 扳手套装MAGNETO SPANNER SET 单开口扳手/呆扳手SINGLE ENDED OPEN JAW SPANNER 双开口扳手DOUBLE OPEN ENDED SPANNER 双开口扳手套装DOUBLE OPEN ENDED SPANNER SET 扩口螺母扳手PLARE NUT SPANNER（OPEN） 半月型梅花扳手HALF-MOON RING SPANNER 双头梅花扳手（短）DOUBLE ENDED SPANNER（SHORT） 双头梅花扳手（长）DOUBLE END

3、ED SPANNER（LONG） 平头梅花扳手（直）FLAT RING SPANNER STRAIGHT PATTERN 开口敲击扳手OPEN ENDED SLOGGING SPANNER 梅花敲击扳手RING SLOGGING SPANNER 高颈梅花敲击扳手DEEP AFFSET RING SLOGGING SPANNER 直头梅花扳手DEEP RING SPANNER（STRAIGHT PATTERN） 延长管EXTENSION TUBE 爪型扳手CROWFOOT SPANNER 两用活头扳手COMBINATION SWIVEL HEAD WRENCH 活结T型扳手SWIVEL HAND

4、LE WITH SLIDING T 套筒扳手SOCKET WRENCH 弯头套筒扳手ANGLED SOCKET WRENCH 双头套筒扳手DOUBLE ENDED SOCKET WRENCH 旋棒TOMMY BAR 分节旋棒STEPPED TOMMY BAR 3C把手套筒扳手SOCKET WRENCH WITH 3C-HANDLE T型及磁性套筒扳手SOCKET WRENCH WITH T-HANDLE AND MAGNET 钩头扳手HOCK SPANNER WITH LUG 带销扳手PIN SPANNER 可调式两爪钩扳手CALIPER FACE SPANNER WITH ADJUSTABL

5、E 1/4'标准六角套筒HEXAGON SOCKET 1/4'加长六角套筒HEXAGON LONG PATTERN SOCKET 棘轮扳手RATCHETS 套筒SOCKETS 套筒套装SOCKETS SETS 摩擦棘轮扳手FRICTION RATCHETS 冲击工具IMPACT TOOLS 旋具头BITS 扭矩扳手TORQUE WRENCHES 1/4梅花套筒SOCKET UD PROFILE 1/4六角套筒 星型套筒SOCKET FOR PROTRUDING HEAD SCREWS 1/4一字，十字，星型，内六角旋具套筒 1/4双向棘轮套筒扳手1/4REVERSIBLE RA

6、TCHET T柄棘轮扳手RATCHET WITH T-HANDLE 手用棘轮头HAND RATCHET WITHOUT HANDLE 1/4转3/8转换接头CONVERTER 1/4 TO 3/8 T型滑动头手柄TOMMY BAR WITH SLIDING T 活动延长杆FLEXIBLE EXTENSION 通用延长杆UNIVERSAL-JOINT EXTENSION 1/4四方驱动连接头SQUARE-DRIVE COUPLER 1/4万向接头UNIVERSAL JOINT 活动头手柄SWIVEL HANDLE 套筒固定夹SOCKET RAIL WITH MAGNETIC 3/8一字，十字，星

7、型，内六角旋具套筒 3/8六角套筒SOCKET HEXAGON 3/8 3/8梅花套筒SOCKET UD PROFILE 塑料棘轮扳手PLASTIC RATCHET 旋具头接头BIT ADAPTOR 旋具头棘轮扳手BIT RATCHET 旋具头螺丝起子BIT SCREWDRIVER 旋具头延长杆BIT EXTENSION 旋具头SCREWDRIVER BITS 1'. 风动套筒IMPACT SOCKET 风动套筒附件ACCESSORIES FOR IMPACT SOCKET 手动操作冲击手柄HAND-OPERATED INPACT DRIVER 摩擦式梅花棘轮扳手FRICTION TY

8、PE RATCHET WITH RING WITH BI-HEXAGON 摩擦式四方棘轮扳手FRICTION TYPE RATCHET WITH SQUARE RING 安装扳手/尖尾扳手CONSTRUCTION RATCHET BI-HEXAGON 0.6-5.4NM扭力螺丝起子TORQUE SCREWDRIVER HANDLE 0.6-5.4NM 3C一字螺丝起子3C-SCREWDRIVER FOR SLOTTED HEAD SCREWS 3C十字PH螺丝起子3C-SCREWDRIVER FOR CRUCIFORM HEAD PH 3C米字螺丝起子 3C星型螺丝起子 3C球头六角螺丝起子

9、5件/6件/7件/155件螺丝起子套装SET FOR HEAD SCREWS 电工螺丝旗子ELECTRONIC SCREWDRIVER 木柄螺丝起子SCREWDRIVERS WITH WOODEN HANDLE 磁化/消磁器MAGNETIZER AND DEMAGNETIZER 方刃锥子SQUARE BLADED AWL T型六角螺丝起子HEXAGON SCREWDRIVER WITH T-HANDLE T型内六角扳手HEXAGON SOCKET KEY WITH T-HANDLE 内六角扳手HEXAGON SOCKET KEY 加长内六角扳手EXTRA LONG HEXAGON SOCKET

10、 KEY 加长球头内六角扳手 内六角扳手套装HEXAGON SOCKET KEY SET T型星形螺丝起子SCREWDRIVER WITH T-HANDLE 曲柄螺丝起子CRANKED SCREWDRIVER 量规GARGE 车灯测电笔CAR LIGHT TESTER 6-24伏测电笔VOLTAGE TESTER 6-24V 150-250伏测电笔VOLTAGE TESTER 150-250V 钳子3件套装PLIERS SET，3-PIECE 万能手钳48件套UNIVERSAL PLIERS ASSORTMENT WITH 48 PIECE 小钢丝钳SMALL COMBINATION PLIE

11、RS 钢丝钳（德式）COMBINATION PLIERS（GERMAN PATTERN） 钢丝钳（欧式）COMBINATION PLIERS（EURO PATTERN） 强力钢丝钳POWER COMBINATION PLIERS 塑料水口钳SIDE CUTTERS FOR PLACTIC 剪钳（瑞典款式）SIDE CUTTERS（SWEDISH PATTERN） 电工剪钳ELECTRICIANS SIDE CUTTERS 剪钳（美国款式）POWER SIDE CUTTERS（AMERICAN PATTERN） 杠杆剪钳LEVER-ACTION SIDE CUTTERS 杠杆顶剪钳LEVER-A

12、CTION END CUTTING NIPPERS 核头钳TOWER PINCERS 拨钉钳PINCERS 平头钳FLAT NOSE PLIERS 圆头钳ROUND NOSE PLIERS 直头尖嘴钳LONG NOSE PLIERS 弯头尖嘴钳 电话钳TELEPHONE PLIERS 强力尖嘴钳TRIPLE-FUNCTION PLIERS 直口机修工钳MECHANICS PLIERS STRAIGHT PATTERN 曲口机修工钳MECHANICS PLIER ANGLED PATTERN 偏口机修工钳MECHANICS PLIER OFFSET PATTERN 30度平圆机修钳MECHANI

13、CS PLIER WITH 30 电缆刀CABLE KNIFE 电工电缆刀ELECTRICIANS CABLE KNIFE 防静电专用钳子 电子钳ELECTRONIC PLIERS 迷你电子钳MINIATURE ELECTRONIC PLIERS 防静电尖嘴钳/防静电顶切钳/电子平头钳/电子剪钳/防静电剪钳/电子剥线钳 电缆 剪钳CABLE CUTTERS 小型万用剪SMALL UNIVERSAL SCISSORS 万用电缆刀UNIVERSAL CABLE KNIFE 自动剥线钳STRIPPING PLIERS ANTOMATIC 剥线钳STRIPPING PLIERS 固定剥线钳STRIP-

14、FIX STRIPPING PLIERS 剥线工具WIRE STRIPPER 高效剥线钳HIGH-PERFORMANCE WIRE STRIPPER 数据传输电缆精确剥线钳PRECISION WIRE STRIPPER FOR DATA CABLES 同轴电缆剥线钳WIRE STRIPPER FOR COAXIAL CABLES 绝缘剥漆钳INSULATING VARNISH STRIPPER 剥线刀WIRE STRIPPING KNIFE 绝缘胶带INSULATING TAPE 压线钳CRIMPING PLIERS 锁把式压线钳LOCK-GRIP CRIMPING PLIERS 端子压线钳W

15、IRE END-SLEEVE PLIERS 模块压线夹钳MODULAR LOCK-GRIP CRIMPING PLIERS 模块压线钳MODULAR CRIMPING PLIERS 精确压线钳PRECISION CRIMPING PLIERS 外卡簧钳（轴用）EXTERNAL CIRCLIP PLIERS（ON SHAFTS） 直头/弯头外卡簧钳（轴用） 内卡簧钳（孔用）INTERNAL CIRCLIP PLIERS（IN BORES） 直头/弯头内卡簧钳（孔用） 大型/重型卡簧钳 X型把X-GRIP 大力钳LOCK-GRIP PLIERS 平行钳夹大力钳PARALLEL JAW LOCK-G

16、RIP PLIERS 宽口大力钳WIDE JAW LOCKING PLIERS 滑行杆式大力钳LOCK-GRIP SLIDE CLAMP 固定大力钳GRIP WRENCH FOR GLUEING 机械工作台钳MACHINE WORKBENCH CLAMP 焊接大力钳LOCK-GRIP WELDING CLAMP 管子焊接大力钳LOCK-GRIP TUBE WELDING CLAMP C型大力钳LOCK-GRIP C CLAMP 水泵钳UNIVERSAL PLIERS（7种设置/5种设置） 水泵钳WATER PUMP PLIERS 特殊水泵钳SPECIAL WATER PUMP PLIERS 可

17、调式高速管子钳HIGH-SPEED PIPE WRENCH WITH SCREW ADJUSTER 高速曲口管子钳HIGH-SPEED PIPE WRENCH CURVED 迷你链式管子钳MINI CHAIN PIPE WRENCH 链钳CHANIN PIPE WRENCH 重型管子钳STILLSON PIPE WRENCH 断线钳BOLT CUTTERS 钳子套装（3件/4件/6件/8件） VDE绝缘安全电工工具VDE INSULATED SAFETY TOOLS VDE绝缘标准符合DIN EN 60900 IEC 60900：2004以及VDE680 适合在高压区安全工作（AC1000V

18、DC1500V） VDE绝缘螺丝起子VDE SCREWDRIVER（一字/十字/米字/星型/内六角） VDE绝缘起子套装 电压传感器/电压测试器VOLTAGE DETECTOR/TESTER 绝缘扭力扳手VDE TORQUE WRENCH 绝缘双向棘轮扳手VDE REVERSIBLE RATCHET 绝缘六角套筒VDE SOCKET HEXAGONAL 绝缘旋具头套筒VDE SCREWDRIVER BIT SLCKET T型绝缘扳手VDE T-HANDLE 绝缘延长杆VDE EXTENSION 绝缘电工工具组套（3件/8件/14件/108件） VED 3C绝缘手柄套筒扳手VDE SOCKET

19、WRENCH WITH 3C HANDLE 绝缘梅花扳手VDE SINGLE-ENDED RING SPANNER WITH DEEP OFFSET 绝缘开口扳手VDE SINGLE-ENDED OPEN SPANNER VDE绝缘钢锯HACKSAW 绝缘电缆刀VDE CABLE KNIFE 绝缘电缆剪CABLE SHEARS 棘轮式绝缘电缆剪钳CABLE CUTTERS VDE绝缘电缆剪VDE CA BLE SHEARS 绝缘剥线钳/绝缘固定剥线钳/绝缘水泵钳/绝缘强力钢丝钳/绝缘斜口钳/绝缘电工斜口钳/绝缘平口钳/绝缘圆头钳/绝缘直头尖嘴钳/绝缘弯头尖嘴钳 VDE绝缘橡胶垫VDE RUBB

20、ER COVER SHEET VDE绝缘电工安全手套VDE ELECTRICIANSS SAFETY GLOVES 绝缘塑料夹VDE PLASTIC CLAMPS 车轮扳手WHEEL WRENCHES 十字扳手4 WAY WHEEL WRENCH 撬棒TYRE LEVER 轮毂罩移除工具HUBCAP RENOVING TOOS 配重钳BALANCE-WEINHT PLIERS 制动弹簧钳BRAKE-SPRING PLIERS 闸线弹簧钳PLIERS FOR BRAKE-CABLE SPRINGS 制动钳刷BRAKE-CALIPER BRUSH 放油塞扳手（四方）DRAIN-PLUG WRENC

21、H WITH SQUARE 油壶OIL CANS 过滤器扳手UNIVERSAL FILTER WRENCH 皮带钳PULLEY WRENCH 阀门研磨机VALVE GRUNDER 阀门研磨工具VALVE LAPPING TOOS 油封钳VALVE-SEAL PLIERS GUNMETAL FINISH 汽缸/活塞环压缩器VALVE SPRING COMPRESSOR BRIGHT NICKEL-PLATDE 活塞环钳PISTON RING PLIERS 软管夹钳HOSE CLIP PLIERS 电极拉马BATTERY TERMINAL PULLER 电池测试器BATTERY TESTER 火花

22、塞套筒SPARK PLUG SOCKET 火花塞套筒扳手SPARK PLUG SOCKET WRENCH 火花塞刷SPARK-PLUG BRUSH 特殊尖冲凿SPECIAL PIN PUNCH 弹簧撑开器SPRING SPREADER 球头拉拔器UNIVERSAL BALL JOINT REMOVER 通用罐UMIVERSAL CANISTER 防冻测试器ANTI-FREEZE TESTER 安装钳INSTALLATION PLIERS 吸盘SUCTION LIFTER 磁性拾取工具MAGNETIC PICK-UP TOOL 金属片切割器NIBBER 杠杆剪切机LEVER-ACTION TIN

23、 SNIPS 打孔钳PUNCH PLIERS 橡胶锤RUBBER HAMMER 塑料锤PLASTIC HAMMER 无后坐力锤RECOILLESS HAMMER 钳工球头锤ENGINEERSS BALL PEIN HAMMER 钳工锤ENGINEERSS HAMMER 平面刮刀FLAT SCRAPER 三角空心刮刀THREE-EDGED HOLLOW-GROUND SCRAPER 三角实心刮刀THREE-EDGED FLAT-GROUND SCRAPER 密封刮刀GASKET SCRAPER 平锉HAND FILE 圆锉ROUND FILE 三角锉TRIANGULAR FILE 半圆锉HALF

24、-ROUND FILE 锉类6件套装 中心冲/凿/开口销冲CENTRE PUNCHES/CHISELS/DRIFT PUNCHES 钢锯HACKSAW 栓孔锯KEYHOLE SAW 小金属锯SMALL METAL SAW 小PUK钢锯PUK JUNIOR HACKSAW HOBBY锯 台钳/台虎钳METALWORKING VICE（100/125/150mm） 钢卷尺STEEL TAPE MEASURE（3米/5米/8米） 阀塞尺VALVE FEELER GAUGE 塞尺 火花塞塞尺SPARK PLUG GAUGE 螺纹规THREAD GAUGE 游标卡尺POCKET VERNIER CALL

25、IPER 数显游标卡尺DIGITAL CALLIPER 划线器SCRIBER 镊子TWEEZERS 十字镊子CROSSLOCK TWEEZERS 螺钉取出器BOLT EXTRACTOR 断螺钉取出器套装SCREW EXTRACTOR SET 机械螺母破开器MECHANICAL NUT SPLITTER 螺栓插入及取出器STUD INSERTER AND EXTRACTOR 丝锥THREAD FILE 管子割刀PIPE CUTTER 自动切割机AUTOMATIC PIPE CUTTER 链式切管机CHAIN PIPE CUTTER 虹吸扳手SI PHON TRAP PLIERS 钢丝刷WIRE

26、BRUSH 锉刀清洁刷FILE CLEANING BRUSH 裁缝剪TAILORS SCISSORS 发光二极管井下检查灯LED INSPECTION LAMP 井下检查灯INSPECTION LAMP 发光二极管工作灯LED WORK LIGHT 工程锤ENGINEERS HAMMER ROTBAND-PLUS 工程圆头锤ENGINEERSBALL PEIN HAMMER 胡桃木备用手柄SPARE HANDLE HICKORY 工匠锤JOINERSHAMMER ROTBAND-PLUS 石匠锤CLUB HAMMER 双面石匠锤DOUBLE FACED CLUB HAMMER ROTBAND-

27、PLUS 大锤SLEDGE HAMMER 大碎石锤STONE SLEDGE HAMMER 劈木锤WOOD SPLITTING HAMMER 铺路锤PAVING HAMMER 单板锤VENEER HAMMER 磁性锤MAGNETIC HAMMER ROTBAND 玻璃装配工锤GLAZIERS HAMMER 炭化合金瓦锤CARBIDE TILE HAMMER 羊角锤CLAW HAMMER 电焊敲锤SCALING HAMMER ROTBAND-PLUS 无弹力安全锤RECOILLESS HAMMER 安全锤SAFETY HAMMER SOFT-PLUS 塑料锤PLASTIC HAMMER 橡皮锤RU

28、BBER MALLET HARD 尼龙锤NYLON HAMMER 木锤WOOLEN MALLET 铜锤COPPER HAMMER CLUB SHAPE 铝锤ALUMINIUM HAMMER ROTBAND 桶形铝锤LEAD HAMMER SARREL SHAPE 冷凿锤COLD CHISEL HAMMER 热凿锤HOT CHISEL HAMMER 平底压摸锤SET HAMMER TOP PART 压槽铁锤TOP FULLER 上型模锤BOTTOM FULLER 冲锤PUNCH HAMMER 镰刀锤SCYTHE HAMMER 锻工钳BLACKSMITHS TONGS 铆钉钳RIVETTING T

29、ONGS 锥型冲子/中心冲子/销式冲子DRIFT PUNCHES/CENTRE PUNCHES/PIN PUNCHES 自动中心冲子AUTOMATIC CENTRE PUNCH WITH TIP 冲子组套DRIFT PUNCH SET 铆钉装配器RIVET SETTER 字母及数字冲子LETTER AND NUMBER PUNCHES 装配冲子SETTING PUNCH 撬杆PRVBAR 起钉器NAIL FIFER OCTAGONAL 撬棍CROWBAR 通用拉马UNIVERSAL PULLER 两爪拉马PULLER 2-ARM PATTERN 三爪拉马PULLER 3-ARM PATTERN

30、 防腐蚀拉马COROSTOP PULLER PATTERN 快速拉马QUICK-ACTION PULLER 两爪液压拉马UNIVERSAL 2-ARM PULLER 拉马延长杆EXTENSION FOR PULLERS 液压轴杆HYDRAULIC PRESSURE SPINDLE 三爪液压拉马UNIVERSAL 2-ARM PULLER 拉马套装PULLER SET 螺母劈开器NUT SPLITTER 液压螺母劈开器NUT SPLITTER HYDRAULIC 螺栓提取器STUD EXTRACTOR 轴承提取器BALL BEARING EXTRACTOR 滚珠轴承提取器套装BALL BEARI

31、NG EXTRACTOR SET 内提取器INTERNAL EXTRACTOR 冲击轴承拉马IMPACT BEARING PULLER 汽缸拉马CYLINDER LINER PULLER COMPLETE WITH SUPPORT BRACE 分离拉马SEPARATOR PULLER 轴承分离器BEARING SEPARATOR 传动轴轴承拉马DRIVE SHAFT BEARING PULLER 分离器及拉马套装SEPARATOR AND PULLER SET 拉拔卡盘PULLING CHUCK 液压泵HYDRAULIC PUMP 液压手泵HYDRAULIC HAND PUMP 液压工具拉马1

32、.50 PULLER FOR HUDRAULIC IMPLEMENT1.50 液压增力器HYDRAULIC PRESS 轮毂拉马WHEEL-HUB PULLER 传动轴拉马DRIVE-SHAFT PULLER 方向盘拉 马STEERING-WHEEL PULLER 装配叉DISMANTLING AND ASSEMBLY FORK 球头拉拔器BALL JOINT PULLER 三爪机滤扳手OIL FILTER HOOK 弹簧撑SPRING SPREADER 塑料轴承安装套装PROFESSINAL PLASTIC BEARING INSTALLATION SET 法兰分离器FLANGE SEPAR

33、ATORS 轨距测量器TRACK ALIGNMENT GAUGE 扳手WRENCHES 管子切割器PIPE CUTTERS 扩口工具FLARING TOOLS 弯管机PIPE BENDERS 管子工具PLUMBING TOOLS 铁皮剪/断线钳TIN SNIPS/BOLT CUTTERS 管子清洁设备PIPE CLEANING EQUIPMENT 弯管系统PIPE BENDING SYSTEMS SNAP管道扳手PIPE WRENCH ECK-SNAP 钢管切割器PIPE CUTTER TUBEX FOR STEEL PIPES 生铁管切割器PIPE CUTTER TUBEX FOR CAST

34、 IRON PIPES 不锈钢管切割器RATCHET PIPE CUTTER NIRO FOR STAINLESS STEEL PIPES 管子修边器PIPE DEBURRING REAMER 不锈钢管修边器PIPE DEBURRING REAMER FOR STAINLESS STEEL PIPES 扩口工具套装FLARING TOOL SET BOERDEX 钢管扩口钳EXPANDER PLIERS FOR COPPER PIPES 带滑轨的弯管机PIPE BENDER WITH SLIDE RAIL 带滚轴的弯管机PIPE BENDER WITH ROLLER 弯管钳PIPE BENDI

35、NG PLIERS 带滑轨的弯管钳PIPE BENDING PLIERS WITH SLIDE RAIL 带滚轴的弯管钳PIPE BENDING PLIERS WITH ROLLER 手动弯管机MANUAL BENDING TOOL 液压弯管机HYDRAULIC PIPE BENDER 手动液压弯管机PIPE BENDING MACHINE FOR MANUAL HYDRAULIC OPERATION 电动液压弯管机PIPE BENDING MACHINE FOR ELECTRO HYDRAULIC OPERATION 管道矫直工具PIPE STRAIGHTENING TOOL 金属片弯边钳S

36、HEET METAL CRINPING PLIERS 折边钳SEAMING PLIERS 快速夹取扳手QUICK-CLAMP WRENCH 夹管钳GRIPPING PLIERS 分级扳手STEPPED KEY 复合分级扳手COMBINATION STEPPED KEY 铁皮剪TIN SNIPS /HOLE CUTTING SNIPS /PELICAN PATTERN SNIPS 断线钳BOLT CUTTER 管道清洁软轴FLEXIBLE PIPE CLEANING SHAFT 排水管清洁器DRAIN PIPE CLEANER 工作台几工作桌WORKBENCHES AND WORK TABLES

37、 工具车TOOL TROLLEYS 工具柜TOOL CABINETS 车间推车WORKSHOP TROLLEYS 抽屉柜/箱DRAWER-CABINETS/BOXES 衣柜/工作服柜WARDROBES 矮橱LOWER CUPBOARD UNIT 图纸夹DRAWING HOLDER 电源面板PWER SUPPLY PANEL 防酸放腐蚀工作台面板 六边形工作台HEXAGONAL WORKBENCH 带抽屉工作台WORKBENCH WITH DRAWER CABINET 塑料抽屉插件PLASTIC DRAWER INSERT 工作桌推车WORKSHOP TABLE TROLIEYS 工作台WORK

38、BENCH 带背板工作台 坚固推车TROUGH TROLLEY 平板车PLATFORM TROLLEY 带手柄平板车PLATFORM TROLLYE WITH HANDLE 维护推车SERVICE TROLLEY 带工具箱车间推车WORKSHOP TROLLEY WITH TOOL CHEST 工具箱TOOL CHEST 存放斗STORAGE TRAY 卷纸架PAPER ROLL HOLDER 垃圾桶WASTE BASKET 移动架写字板LECTERN WORKTOP 存储盒S TORAGE BOXES 带门库架CUPBOARD WITH SHELVING WITH DOORS 开敞式壁板CO

39、MPLETE PANEL SYSTEM WITH SLOTTED PANELS 存物柜LOCKER WITH HINGED DOORS 滑门橱CUPBOARD WITH SLIDING DOORS 电脑柜COMPUTER CABINET 桌上设备DESK INSTALLATION 移动电脑架PC STAION MOBILE 电脑车间组合PC WORKPLACE COMBINATION 更衣室条凳CHANGING CUBICLE SEAT BENCH 安全橱SAFETY CUPBOARD 衣橱CLOTHES LOCKER 带凳子的衣橱CLOTHES LOCKER WITH SEAT BENCH

40、消防员衣橱FIREFIGHTERS CUPBOARD 工具橱TOOL CABINET 移动式可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER MOBILE 固定可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER STATIONARY 分类垃圾收集站WASTE-COLLECTION STATION CONTAINER 立式烟灰缸STAND ASHTRAY OCHSENKOPF系列斧头 欧洲ILTIS型斧 制图用刮刀 专业伐木斧 快劈斧 抢险袖珍刀 CAROLUS特殊工具 KLANN汽车专用工具 弹簧压缩器 横杆

41、球头拉拔器 轮轴拉马 液压手用压力器 轴衬提取器 发动机锁定工具套装 扭距测试仪及设备TORQUE TESTER AND EQUIPMENT 扭距倍增器TORQUE MULTIPLIERS 扭距角度指示器TORQUE ANGLE INDICATORS 特殊DREMO工具SPECIAL DREMO TOOLS DREMOMETER系列扭力工具DREMOMETER TOOLS 扭距螺丝刀TORQUE SCREWDRIVERS 扭距扳手/扭力扳手TORQUE WRENCHES 电子扭距测试仪ELECTRONIC TORQUE TESTER DKD校准遵守DKD准则3-7/3-8/DIN EN ISO

42、 6789 RAHSOL DREMOTEC产品校准按照DIN EN ISO 6789标准 迷你型扭距扳手DREMOMETER MINI DREMOMETER高强度铝合金扭距扳手 含： DREMOMETER 1-12NM /10-100LBF.IN （塑料外表） DREMOMETER 6-30NM /50-270LBF.IN DREMOMETER 8-40NM /70-350LBF.IN DREMOMETER 20-120NM /15-90LBF.FT DREMOMETER 40-200NM /30-150LBF.FT DREMOMETER 50-300NM /35-220LBF.FT DREM

43、OMETER 80-360NM /60-260LBF.FT DREMOMETER 110-550NM /80-405LBF.FT DREMOMETER 140-760NM /105-560LBF.FT DREMOMETER 520-1000NM /380-730LBF.FT DREMOMETER 750-2000NM DREMOMETER 1500-3000NM DREMOMETER系列棘轮头RATCHET HEADS DREMOMTER 扭距限制接合器TORQUE LIMIT UNIT 转角仪TORQUE ANGLE INDICATOR 圆形插头式扭距扳手（覆盖范围8-1000NM） 开口扳

44、子头OPEN END RTTING 梅花扳子头RING END RTTING 半开口梅花扳子头FLARED END FITTING 棘轮头RATCHET HEAD 四方头FIXED SQUARE HEAD 方形插头式扭距扳手（覆盖范围8-400NM） 开口插头RECTANGULAR OPEN END RTTING 梅花插头RECTANGULAR RING END RTTING 半开口梅花插头RECTANGULAR FLARED END RTTING TORCOFIX系列带四方驱动的扭距扳手 TORCOFIX K扭距扳手（四方头）TORQUE WRENCH TORCOFIX K 含： 4549-

45、01 1-5NM 1/4方头 4549-02 2-25NM 1/4方头 4549-05 5-50NM 3/8 方头 4550-10 10-100NM 1/2方头 4550-20 20-200NM 1/2方头 4550-30 60-300NM 1/2方头 4550-40 75-400NM 1/2方头 4550-55 100-550NM 3/4方头 4550-75 140-750NM 3/4方头 TORCOFIX K扭距扳手套装TORCOFIX K TORQUE WRENCH SET TORCOFIX K快速旋转把手QUICK-TURN WITH T-GRIP TORCOFIX K 蘑菇头MUSHROOM HEAD TORCOFIX Z扭距扳手（圆形插头）TORQUE WRENCH TORCOFIX Z TORCOFIX