激光对中仪对中

1、会计学1激光对中仪对中激光对中仪对中第1页/共43页1999 Fixturlaser AB2第2页/共43页对中的目的对中的目的1999 Fixturlaser AB3第3页/共43页引起设备不对中的因素引起设备不对中的因素1999 Fixturlaser AB4第4页/共43页不对中的分类不对中的分类1999 Fixturlaser AB5第5页/共43页对中的方法对中的方法1999 Fixturlaser AB6第6页/共43页1999 Fixturlaser AB7第7页/共43页1999 Fixturlaser AB8第8页/共43页1999 Fixturlaser AB9第9页/共4

2、3页1999 Fixturlaser AB10第10页/共43页1999 Fixturlaser AB11第11页/共43页1999 Fixturlaser AB12nUse the bracket hook to “catch” the chain.nThe other end of the chain goes under the shaft and will fit into the bracket cradle to secure the bracket to the shaft.第12页/共43页1999 Fixturlaser AB13nTD-M 安装在调整端轴. nTD-S 安装

3、在基准端轴.第13页/共43页1999 Fixturlaser AB14第14页/共43页1999 Fixturlaser AB15第15页/共43页1999 Fixturlaser AB16第16页/共43页1999 Fixturlaser AB17 第17页/共43页1999 Fixturlaser AB18第18页/共43页1999 Fixturlaser AB19第19页/共43页1999 Fixturlaser AB20第20页/共43页1999 Fixturlaser AB21系统将以最接近的数值显示结果:第21页/共43页1999 Fixturlaser AB22这个系统将平均整

4、个选定时间的样本。如果数值波动，你要增加时间。第22页/共43页1999 Fixturlaser AB23这个系统将混合新、老读数使显示值慢下来。 0 时没有屏幕过滤，10 为最大。已记录的测量数值不会受到影响。第23页/共43页1999 Fixturlaser AB24时钟法要求你放置 TDs 于 9:00, 3:00, & 12:00位置. 三点法（TriPoint ）使你在旋转不小于60度得到测量结果第24页/共43页1999 Fixturlaser AB25垂直调节水平调节第25页/共43页1999 Fixturlaser AB26第26页/共43页1999 Fixturlaser A

5、B27: 第27页/共43页1999 Fixturlaser AB28倾角计将引导你转到 9:00 . 第28页/共43页1999 Fixturlaser AB29第29页/共43页1999 Fixturlaser AB30第30页/共43页1999 Fixturlaser AB31The foot values give the movable machines position at the feet where corrections are made. Negative values mean the machine is low and must be shimmed. Positi

6、ve values mean the machine is high. Therefore, shims will be removed.The angle and offset values are used to determine the alignment quality. These values are compared to alignment tolerances to determine whether correction is necessary.Angular Misalignm entm m /100 m mOffset Misalignm entm mRPMExce

7、llentAcceptableExcellentAcceptable36000.3/10.5/10.030.0518000.5/10.7/10.050.112000.7/1”1.0/10.080.159001.0/11.5/10.10.2第31页/共43页1999 Fixturlaser AB32Angular Misalignm entm m /100 m mOffset Misalignm entm mRPMExcellentAcceptableExcellentAcceptable36000.3/10.5/10.030.0518000.5/10.7/10.050.112000.7/1”1

8、.0/10.080.159001.0/11.5/10.10.2The foot values give the movable machines position at the feet where corrections are made. Negative values mean the machine is towards you and must be pushed away. Positive values mean the machine is away from you. Therefore, you will move it towards you.The angle and

9、offset values are used to determine the alignment quality. These values are compared to alignment tolerances to determine whether correction is necessary.第32页/共43页1999 Fixturlaser AB33不对中数值大于不对中数值大于 1 mm (0.025”):1. Make initial vertical corrections2. Make initial horizontal corrections3. Make final

10、 vertical corrections4. Make final horizontal corrections不对中数值小于不对中数值小于 1 mm (0.025”):1. Make final vertical corrections2. Make final horizontal corrections第33页/共43页1999 Fixturlaser AB34n.n地脚的负值意味调整端低，因此应该加垫片.第34页/共43页1999 Fixturlaser AB35.n地脚的负值意味调整端低，因此应该加垫片。第35页/共43页1999 Fixturlaser AB36第36页/共43页

11、1999 Fixturlaser AB37第37页/共43页1999 Fixturlaser AB38切记切记在完成最终调整后一定重新测量.第38页/共43页1999 Fixturlaser AB39第39页/共43页1999 Fixturlaser AB40第40页/共43页1999 Fixturlaser AB41nUse the bracket hook to “catch” the chain.nThe other end of the chain goes under the shaft and will fit into the bracket cradle to secure t

12、he bracket to the shaft.第41页/共43页1999 Fixturlaser AB42垂直调节水平调节第42页/共43页1999 Fixturlaser AB43Angular Misalignm entm m /100 m mOffset Misalignm entm mRPMExcellentAcceptableExcellentAcceptable36000.3/10.5/10.030.0518000.5/10.7/10.050.112000.7/1”1.0/10.080.159001.0/11.5/10.10.2The foot values give the movable machines position at the feet where corrections are made. Negative values mean the machine is towards you and must be pushed away. Positive values mean the machine is away from you. Therefore, you wi