PT_实验(三)_交换机划分VLAN配置

1、PT实验(三) 交换机划分VLAN配置一、实验目标· 理解虚拟 LAN(VLAN)基本原理；· 掌握一般交换机按端口划分 VLAN的配置方法；· 掌握Tag VLAN配置方法。二、实验背景某一公司内财务部、销售部的PC通过2台交换机实现通信；要求财务部和销售部内的PC可以互通，但为了数据安全起见，销售部和财务部需要进行隔离，现要在交换机上做适当配置来实现这一目的。三、技术原理· VLAN是指在一个物理网段内，进行逻辑的划分，划分成若干个虚拟局域网。VLAN最大的特性是不受物理位置的限制，可以进行灵活的划分。VLAN具备了一个物理网段所具备的特性。相同VL

2、AN内的主机可以相互直接通信，不同VLAN间的主机之间互相访问必须经由路由设备进行转发。广播数据包只可以在本VLAN内进行广播，不能传输到其他VLAN中。· Port VLAN是实现VLAN的方式之一，它利用交换机的端口进行VLAN的划分，一个端口只能属于一个VLAN。· Tag VLAN是基于交换机端口的另外一种类型，主要用于使交换机的相同VLAN内的主机之间可以直接访问，同时对于不同VLAN的主机进行隔离。Tag VLAN遵循IEEE802.1Q协议的标准。在使用配置了Tag VLAN的端口进行数据传输时，需要在数据帧内添加4个字节的802.1Q标签信息，用于标示该数据

3、帧属于哪个VLAN，便于对端交换机收到数据帧后进行准确的过滤。四、实验步骤实验拓扑1、设置四台PC机IP地址如图所示。2、对交换机S1进行设置。Switch>enSwitch#conf tEnter configuration commands, one per line. End with CNTL/Z.Switch(config)#hostname S1 /设置主机名S1(config)#vlan 2 /划分VLAN 2S1(config-vlan)#exitS1(config)#vlan 3 /划分VLAN 3S1(config-vlan)#exitS1(config)#inter

4、face fa0/1S1(config-if)#switchport mode access /将fa0/1划分到VLAN 2S1(config-if)#switchport access vlan 2 /将fa0/1划分到VLAN 2S1(config-if)#exitS1(config)#interface fa0/2S1(config-if)#switchport mode accessS1(config-if)#switchport access vlan 3 /将fa0/2划分到VLAN 3S1(config-if)#exitS1(config)#interface fa0/24 /

5、设置fa0/24端口模式为trunk（级联模式）S1(config-if)#switchport mode trunkS1(config-if)#endS1#%SYS-5-CONFIG_I: Configured from console by consoleS1#show vlan /查看VLAN划分情况VLAN Name Status Ports- - - - default active Fa0/3, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15, Fa0/16,

6、 Fa0/17, Fa0/18 Fa0/19, Fa0/20, Fa0/21, Fa0/22 Fa0/23, Gig1/1, Gig1/2 VLAN0002 active Fa0/1 VLAN0003 active Fa0/2 fddi-default act/unsup token-ring-default act/unsup fddinet-default act/unsup trnet-default act/unsupVLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 TranS1- - - - - - - - -

7、 - - enet 100001 1500 - - - - - 0 0 enet 100002 1500 - - - - - 0 0 enet 100003 1500 - - - - - 0 0 fddi 101002 1500 - - - - - 0 0 tr 101003 1500 - - - - - 0 0 fdnet 101004 1500 - - - ieee - 0 0 trnet 101005 1500 - - - ibm - 0 0 Remote SPAN VLANs-Primary Secondary Type Ports- - - -S1#show running-conf

8、igBuilding configuration.Current configuration : 1080 bytes!version 12.2no service timestamps log datetime msecno service timestamps debug datetime msecno service password-encryption!hostname S1!interface FastEthernet0/1 switchport access vlan 2!interface FastEthernet0/2 switchport access vlan 3!int

9、erface FastEthernet0/3!.!interface FastEthernet0/24 switchport mode trunk!interface GigabitEthernet1/1!interface GigabitEthernet1/2!interface Vlan1 no ip address shutdown!line con 0!line vty 0 4 loginline vty 5 15 login!endS1#3、对交换机S2进行设置。Switch>enSwitch#conf tEnter configuration commands, one pe

10、r line. End with CNTL/Z.Switch(config)#hostname S2S2(config)#vlan 2S2(config-vlan)#exitS2(config)#vlan 3S2(config-vlan)#exitS2(config)#interface fa0/1S2(config-if)#switchport access vlan 2S2(config-if)#exitS2(config)#interface fa0/2S2(config-if)#switchport access vlan 3S2(config-if)#exitS2(config)#i

11、nterface fa0/24S2(config-if)#switchport mode trunk S2(config-if)#endS2#%SYS-5-CONFIG_I: Configured from console by consoleS2#show vlanVLAN Name Status Ports- - - - default active Fa0/3, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15, Fa0/16, Fa0/17, Fa0/18 Fa0/

12、19, Fa0/20, Fa0/21, Fa0/22 Fa0/23, Gig1/1, Gig1/2 VLAN0002 active Fa0/1 VLAN0003 active Fa0/2 fddi-default act/unsup token-ring-default act/unsup fddinet-default act/unsup trnet-default act/unsup VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2- - - - - - - - - - - enet 100001 15

13、00 - - - - - 0 0 enet 100002 1500 - - - - - 0 0 enet 100003 1500 - - - - - 0 0 fddi 101002 1500 - - - - - 0 0 tr 101003 1500 - - - - - 0 0 fdnet 101004 1500 - - - ieee - 0 0 trnet 101005 1500 - - - ibm - 0 0 Remote SPAN VLANs-Primary Secondary Type Ports- - - -S2#show running-config Building configu

14、ration.Current configuration : 1080 bytes!version 12.2no service timestamps log datetime msecno service timestamps debug datetime msecno service password-encryption!hostname S2!interface FastEthernet0/1 switchport access vlan 2!interface FastEthernet0/2 switchport access vlan 3!interface FastEtherne

15、t0/3!.!interface FastEthernet0/24 switchport mode trunk!interface GigabitEthernet1/1!interface GigabitEthernet1/2!interface Vlan1 no ip address shutdown!line con 0!line vty 0 4 loginline vty 5 15 login!endS2#五、验证打开PC1的Command PromptPacket Tracer PC Command Line 1.0PC>ipconfigIP Address.: 192.168.

16、1.2Subnet Mask.: 255.255.255.0Default Gateway.: 192.168.1.1PC>ping 192.168.1.3Pinging 192.168.1.3 with 32 bytes of data:Request timed out. /不同VLAN间无法PING通Request timed out.Request timed out.Request timed out.Ping statistics for 192.168.1.3: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),PC>ping 192.168.1.4Pinging 192.168.1.4 with 32 bytes of data:Reply from 192.168.1.4: bytes=32 time=172ms TTL=128 /相同VLAN可以PING通Reply from 192.168.1.4: bytes=32 time=78ms TTL=128Reply from 192.168