航发pcf1报告全尺寸.part1measured

1、CS11_Fully measured ReportProject Name Part Number CAD NumberProduct Name:CS11:_003: VERTICAL SUPPORT LOWER RHr:VCC Material standards : VDA 239-CR300LA Actual Material : CR300LAThickness: 2.0mmCoating thickness : UC Detection time :2016/12/13CHECK RESULT 检查结果CHECK DATE检测日期OK.RATIOPart codeP1P2P3TOT

2、AL全尺寸OK Ratio100%100%100%OK Pos828282Total Pos828282SURF.型面OK Ratio100%100%100%OK Pos575757Total Pos575757TRIM修边OK Ratio100%100%100%OK Pos212121Total Pos212121HOLE孔位孔径OK Ratio100%100%100%OK Pos444Total Pos444RPS Information精密模具-CAStep1:Sureace Checking第 1 页精密模具-CA第 2 页精密模具-CA第 3 页精密模具-CAStep2:Trim C

3、hecking第 4 页精密模具-CA第 5 页精密模具-CAStep3:Holesition第 6 页Step 4 : Hole size Checkingnominal12.1(00.15)12.1(00.15)actual12.2112.21deviation00nominalactualdeviationRPS1RPS2Step 5 : ThinningREPORT CHECKING THINNESMeasure thickness request: 2mmactual thickness 1.99mmLIMITS MAX : 20%11.9510121138121314151621.

4、9431.8841.8451.9461.9671.9181.7791.97101.89111.92121.83131.89141.78151.92161.92THINNING MAX16%56479REPORT CHECKING THINNESMeasure thickness request: 2mmactual thickness 1.99mmLIMITS MAX : 20%171.65233022292819271817312524181.88191.87201.91211.88221.92231.91241.98251.82261.92271.92281.91291.87301.863

5、11.95262021Step 6 : Appearance CheckingAppearance Checking 外观检查NO判定标准 Control standard检验方法 Methond判定OK、NG、N/APicture1零件是否正确？ Is the rignt part?Visual目视OK2变薄率是否料厚20%范内 THINNING MAX no more 20%Venire caliper 游标卡尺OK3是否有开裂、暗裂？ No crack,deformationVisual目视OK4毛边、毛刺、尖角是否0.3mm 范围内？ glitches, indenion,damage

6、d,Venire caliper 游标卡尺OK5是否有模痕、压伤（无手感可接受）？ No roughness detect with the handwith the handOK6是否有拉伤、划伤？No degradation or deformation手触 with the handOK7是否有起皱、变形（装配面平面度需 0.2MM 以内）？No crack,deformationVisual /Venire caliper目视/游标卡尺OK8是否有生锈？Rust?Visual目视OK9字印是否正确、明显且无手 感？Marking information crrect ?Visual/ with the hand目视/手触OK10公差是否与 3D 公差相符？ Report tolerance is the same with 3D?检查 checkingOK11零件定位是否与检具定义相符？ PRS is the same with gauge?检具gaugeOK12料边断差是否超过公差带的 50%？ Trim no moren 50%