塑料零部件原说明材料及物理性能标准规范

附件1：第二批27类塑料零部件原材料及物理性能标准序号零部件名称二级件名称使用材料模具收缩率（%）密度（g/cm3）灰分（%）拉伸（Mpa）断裂伸长率（%）弯曲（23°Mpa)悬臂梁冲击(J/m）弯曲模量（）热变形温度(@1.82mpa)1变速操纵护罩PP+IM-T201.0-1.31.05±0.0320±4≥18≥30≥22≥802导流罩PP+IM-T300.9-1.11.09±0.0330±4≥14≥30≥18≥1203灯具塑料壳大灯灯罩PC0.4-0.71.20±0.03≤1≥64≥50≥82≥750大灯后壳PP+T201.0-1.31.05±0.0320±4≥18≥30≥22≥100后尾灯后壳ABS＋PC0.4-0.71.12±0.03≤1≥45/≥60≥35095后尾灯灯罩雾灯灯罩PC0.4-0.71.20±0.03≤1≥64≥50≥82≥750雾灯灯壳PP+T201.0-1.31.05±0.0320±4≥18≥30≥22≥804车门内护面本体及其他PP+EPDM-T201.0-1.31.05±0.0320±4≥18≥30≥22≥100≥1500门锁扣手罩ABS0.4-0.71.04±0.03≤1≥40/≥55≥70/门锁扣手罩PP+EPDM-T201.0-1.31.05±0.0320±4≥18≥30≥22≥100≥15005暖风壳体PP+IM-T201.0-1.31.05±0.0320±4≥18≥30≥22≥906天窗壳体/旋钮ABS0.4-0.71.04±0.03≤1≥40/≥55≥70PP+IM-T201.0-1.31.05±0.0320±4≥18≥30≥22≥807转向护罩PP+IM-T201.0-1.31.05±0.0320±4≥18≥30≥22≥808空滤器外壳PP+GF250.6-0.91.13±0.0325±4≥45/≥80≥959电瓶盖板PP+T101.2-1.50.96±0.0310±4≥20/≥22≥80ABS0.4-0.71.04±0.03≤1≥40/≥55≥7010高位进气管HDPE0.95±0.03≤1≥14/≥18≥9011地毯压条PP+EPDM-T151.2-1.51.01±0.0315±4≥15≥50≥17≥120PP+IM-T201.0-1.31.05±0.0320±4≥18≥30≥22≥10012电瓶壳体PP0.9±0.03≤1≥16/≥20≥12013手刹护罩PP+IM-T201.0-1.31.05±0.0320±4≥18≥30≥22≥8014组合开关包壳ABS0.4-0.71.04±0.03≤1≥40/≥55≥70PP+IM-T201.0-1.31.05±0.0320±4≥18≥30≥22≥8015安全带包壳ABS0.4-0.71.04±0.03≤1≥40/≥55≥70锁扣座PP+T101.2-1.50.96±0.0310±4≥20/≥22≥8016大灯装饰板ABS0.4-0.71.04±0.03≤1≥40/≥55≥70PC+ABS0.4-0.71.12±0.03≤1≥45/≥60≥3509517车门下饰板PP+IM-T201.0-1.31.05±0.0320±4≥18≥30≥22≥8018洗涤器HDPE0.95±0.03≤1≥14/≥18≥9019座椅调节器包壳PP+PE+T151.2-1.51.01±0.0315±4≥16≥40≥18≥10020登车扶手PP+T10+IM1.2-1.60.99±0.0310±4≥20≥30≥22≥8021内视镜壳体ABS0.4-0.71.04±0.03≤1≥40/≥55≥7022车轮防尘罩ABS0.4-0.71.04±0.03≤1≥40/≥55≥7023洗涤器喷嘴ABS0.4-0.71.04±0.03≤1≥40/≥55≥7024雨刮器刮片衬套POM1.8-2.21.41±0.03≤1≥45/≥70≥4025挡泥板支架PA66+GF300.3-0.61.36±0.0330±4≥140/≥200≥8026门锁手柄内手柄PC+ABS0.4-0.71.12-1.2≤1≥45/≥60≥350门锁手柄(H)外手柄PC+ABS0.4-0.71.12-1.2≤1≥45/≥60≥350门锁手柄(K)外手柄PA6+GF300.3-0.61.36±0.0330±4≥170≥4≥270≥150时代其他系列外手柄ABS0.4-0.61.04±0.03≤1≥48≥20≥55≥7027玻璃升降器摇把普通车型ABS0.4-0.61.04±0.03≤1≥48≥20≥55≥7095H/K车型POM1.8-2.21.41±0.03≤1≥60≥50≥85≥6110附件2：第一批13类塑料零部件原材料及物理性能标准(修订后)注：修改部分为蓝色字体序号零部件类别内含件原材料要求原材料物性要求备注模具收缩率(%)密度g/cm3)灰分(%)拉伸(Mpa)断裂伸长率(%)弯曲(23°Mpa)悬臂梁冲击(J/m)热变形温度(@1.82mpa)测试方法：GB/T14235测试方法：GB1033测试方法：GB/T9345测试方法：GB/T1040测试方法：GB/T1040测试方法：GB-T9341测试方法：GB/T1843测试方法：GB/T16341保险杠总成保险杠本体PP+T25+IM0.9-1.21.07±0.0325±4≥14≥30≥18≥120除（驭菱2010款）PP+T25+IM0.9-1.21.07±0.0325±4≥17≥30≥19≥150驭菱2010款2下护栅总成下护栅本体ABS0.4-0.71.04±0.03≤1≥40/≥55≥70下护栅网格PP+T25+IM0.9-1.21.07±0.0325±4≥14≥30≥18≥1203仪表板总成本体PP+T20+IM1.0-1.31.05±0.0320±4≥18≥30≥22≥100出风口PC+ABS0.4-0.71.12±0.03≤1≥45/≥60≥35095烟灰缸PF+40GF1.43±0.0340±4≥42/≥68≥16杂物箱CO-PP1.8-2.20.9±0.03≤1≥22≥50≥28≥60除霜风管、风道（吹塑）HDPE0.95±0.03≤1≥14/≥18≥100除霜风管、风道（注塑）PP+T201.0-1.21.05±0.0320±4≥22/≥25≥35仪表罩PP+T20+IM1.0-1.31.05±0.0320±4≥18≥30≥22≥100仪表罩ABS+PC0.4-0.71.10±0.03≤1≥40/≥55≥30090中控面板ABS（黑）0.4-0.71.04±0.03≤1≥40/≥55≥704前围装饰板总成前围装饰板PC+ABS0.4-0.71.12±0.03≤1≥45/≥60≥350955全包内饰注塑全包内饰PP+T101.2-1.50.96±0.0310±4≥20/≥22≥80吸塑全包内饰ABS1.05±0.03≤1≥35/≥45≥1506储油杯总成储油杯杯体HDPE0.95±0.03≤1≥14/≥18≥907挡泥板总成挡泥板PP+T15+IM1.2-1.51.0±0.03≤1≥15≥50%≥17≥1208后视镜总成后视镜壳体ABS1.04±0.03≤1≥40/≥65≥140PP+T100.95±0.0310±4≥20≥80≥28≥130后视镜静座PA6+GF301.26±0.0330±4≥65/≥100≥609继电器盒、保险丝盒继电器盒、保险丝盒PA661.5-1.91.14±0.03≤1≥60/≥65≥3510脚踏板总成脚踏板本体PP+30GF+IM0.5-0.71.12±0.0330±4≥65/≥90≥100脚踏板本体PP+T15+IM1.2-1.51.0±0.0315±4≥15≥50%