Cisco 控制器5508操作手册.ppt

1、1,( 网络部分 ),资材物流管理系统 无线控制器5508操作手册,2,项目名称： 资材物流管理系统（网络部分） 用户操作手册 江苏异博科技发展有限公司 2012-11,3,编写说明,4,目 录,5,Cisco 5508 series Wireless Controller,Cisco 1242 AP,Cisco,PDA-手持终端,关于5508无线控制器,需扫描货物,6,安装和初始化,将5508通过Console 线连接到电脑端COM口，同时将网线连接至电脑端，安装SecureCRTPortable（或者windows超级终端，主要是初始化调试命令用）。,设置CRT软件如下 （根据实际情况选择

2、端口）,7,终端调试初始化数据,(Cisco Controller) Welcome to the Cisco Wizard Configuration Tool Use the - character to backup Would you like to terminate autoinstall? yes: yes System Name Cisco_b4:4b:e4 (31 characters max): AUTO-INSTALL: process terminated - no configuration loaded Enter Administrative User Name

3、(24 characters max): cisco Enter Administrative Password (3 to 24 characters): * Re-enter Administrative Password : * Service Interface IP Address Configuration staticDHCP: static Service Interface IP Address: 10.0.0.1 Service Interface Netmask: 255.255.255.0 Enable Link Aggregation (LAG) yesNO: yes

4、,8,Make Presentation much more fun,Management Interface IP Address: 10.125.63.84 Management Interface Netmask: 255.255.255.0 Management Interface Default Router: 10.125.63.1 Management Interface VLAN Identifier (0 = untagged): Management Interface DHCP Server IP Address: 10.125.63.1 Virtual Gateway

5、IP Address: 1.1.1.1 Mobility/RF Group Name:5508 Network Name (SSID): 5508 Configure DHCP Bridging Mode yesNO: yes Warning! Enabling Bridging mode will disable Internal DHCP server and DHCP Proxy feature. May require DHCP helper functionality on external switches. Allow Static IP Addresses YESno: yes

6、 Configure a RADIUS Server now? YESno: no Warning! The default WLAN security policy requires a RADIUS server. Please see documentation for more details. Enter Country Code list (enter help for a list of countries) US: it / *语言选择* / Enable 802.11b Network YESno: yes Enable 802.11a Network YESno: yes

7、Enable 802.11g Network YESno: yes Enable Auto-RF YESno: yes,9,Configure a NTP server now? YESno: no Configure the system time now? YESno: no Warning! No AP will come up unless the time is set. Please see documentation for more details. Configuration correct? If yes, system will save it and reset. ye

8、sNO: yes Configuration saved! Resetting system with new configuration. Configuration saved! Resetting system with new configuration. Restarting system. ? WLCNG Boot Loader Version 1.0.1 (Built on Apr 11 2009 at 13:32:33 by cisco) Board Revision 1.3 (SN: FCW1548L0AW, Type: AIR-CT5508-K9) (G),重启后开始设置开

9、启5508的WEB配置模式,10,(Cisco Controller) (Cisco Controller) config network webmode enable (Cisco Controller) config network secureweb enable You must reboot for the change to take effect. (Cisco Controller) save config Are you sure you want to save? (y/n) Y Configuration Saved! (Cisco Controller) reset s

10、ystem Are you sure you would like to reset the system? (y/N) Y System will now restart!Restarting system. WLCNG Boot Loader Version 1.0.1 (Built on Apr 11 2009 at 13:32:33 by cisco) Board Revision 1.3 (SN: FCW1548L0AW, Type: AIR-CT5508-K9) (G) Verifying boot loader integrity. OK.,11,远程管理及相关设置,在浏览器地址

11、栏中输入控制器地址：,浏览器跳转到如下 登录页面点击Login：,12,输入用户名及密码：,13,登陆后显示界面如下图：,14,点击CONTRILLER进入相关网络接口设置：,15,点击：,按钮，进入后点击,设置相关接口数据如下图：,（此处可以设置的是5508控制器的远程地址及无线AP需要指向的地址）,16,点击：,返回到接口界面，点击右上角的,新建一个接口：ap-manage，用于无线AP的使用，如下图：,17,点击WLAN进入WLAN设置：,选择右上角的 Create New,之后点击GO按钮，确定添加一个新的Wlan,18,广播策略默认即可：ALL,这里选择刚才新建的接口： ap-man

12、age,设置相关参数如下图：,19,20,21,附加说明：对于使用供电模块的无线AP，我们需要在控制器里执行如下操作: 1、进入,1、进入,2、点击已经注册到无线控制器的AP，显示如下图,22,3、点击Advanced,4、在Power Over Ethernet Settings中 执行如下设置,23,1、点击WIRELESS,进入AP列表查看界面,24,2、点击左边的802.11b/g/n,3、将鼠标放置于需要设置AP列表的 后边小箭头，弹出对话框中选择： Configure,5、AP天线的DBI功率增益调整,4、AP的Admin Status模式调整为Enable,25,MAC 过滤设置,1、点击菜单栏上的SECURITY,2、点击左边菜单栏的 MA