50、80吨汽车吊性能表

1、.50 吨汽车起重机性能表（主表）以下工况仅供参考，实际请与本公司业务员联系！不支第五支腿，吊臂位于起重机前方或后方；支起第五支腿，吊臂位于侧方、后方、前方工作半径 (m)主臂长度 (m)10.7018.0025.4032.7540.103.050.003.543.004.038.004.534.005.030.0024.705.528.0023.506.024.0022.2016.306.521.0020.0015.007.018.5018.0014.1010.208.014.5014.0012.409.207.509.011.5011.2011.108.306.5010.09.2010.0

2、07.506.0012.06.407.506.805.2014.05.105.704.6016.04.004.703.9018.03.103.703.3020.02.202.902.9022.01.602.302.4024.01.802.0026.01.401.5028.01.2030.00.90各臂二0100100100100伸缩三003366100率四003366100（%）五003366100钢丝绳倍率128543吊钩重量0.5150.215( 注: 本表内红字及红字以上栏目的数字为吊臂强度所决定, 其下面栏目数字为倾翻力矩决定).50 吨汽车起重机性能表（副臂）吊臂位于起重机侧方或后方

3、吊臂长度（ m）40.10+5.1040.10+9.0040.10+16.10主臂仰角（）主臂 +副臂主臂 +副臂主臂 +副臂020020020784.03.63.21.91.50.8753.83.23.01.81.30.8723.22.92.81.71.20.7703.02.52.51.61.20.6652.52.02.01.41.10.5601.91.61.51.00.80.5551.40.81.00.60.60.4各节二臂伸三100缩率四(%) 五钢丝绳倍率1吊钩重量0.1.80 吨汽车起重机起重性能表( 一 )以下工况仅供参考，实际请与本公司业务员联系！主臂起重性能表吊臂长度 ( 支腿

4、全伸 )吊臂长度工作半径 (m)( 不伸支腿 )12.0m18.0m24.0m30.0m36.0m40.0m44.0m12.0m2.580.045.015.03.080.045.035.015.03.580.045.035.015.04.070.045.035.011.74.562.045.035.027.09.55.056.040.032.027.08.05.550.037.029.227.022.06.86.045.034.327.225.022.05.86.539.431.525.323.222.018.05.07.035.629.123.721.520.318.04.38.027.82

5、5.421.018.817.715.712.03.29.520.820.817.815.714.613.212.02.010.019.219.217.015.013.812.611.41.711.016.515.613.512.411.410.411.814.714.712.611.410.69.712.014.214.212.411.210.49.513.012.512.511.310.29.38.814.610.010.010.09.08.57.815.09.49.49.48.78.27.616.08.18.18.17.77.117.86.26.26.26.86.320.04.54.54.

6、55.15.622.03.43.44.04.423.03.03.03.53.926.01.72.22.627.01.92.228.01.61.930.01.01.331.01.1.80 吨汽车起重机起重性能表( 二 )主要技术参数副臂起重性能支腿全伸在两侧或后部吊装名称参数主臂仰角44m主臂 +9.5m 副臂 5夹角44m主臂 +15m副臂 5夹角工作半径 (m)起重性能 (t)工作半径 (m)起重性能 (t)全车总重63.00t81.3 10.06.0011.54.00主臂全伸时44.00m80.4 11.06.0012.64.00长度主臂全缩时12.00m 80.1 11.35.9013.04.00长度最大仰角8278.6 13.05.2014.63.75最大爬坡能16%75.2 16.04.4018.23.05力最小转弯半15.40% 70.8 20.03.6022.52.55径最大提升高58.50m 66.0 24.0