se_1738_digitalanalog_faceplate_filesse_1738_digitalanalog_faceplate_user_instructions_W

1、User Instructions: SE 1738 ArmorPoint I/O Faceplates09/11/07 Rev 1.0The SE 1738 ArmorPoint I/O Faceplates files allow you to quickly load, configure and use preconfigured status and diagnostic displays or faceplates for 1738 Digital and Analog I/O using RSView Supervisory Edition.The pictures below

2、show examples of the on-top status and diagnostic displays or faceplates for both digital and analog 1738 I/O modules. These displays can be launched using any one of the methods available for display navigation (i.e. Display command, Display List Selector).Digital Faceplate ExampleAnalog Faceplate

3、Example9System CompatibilityThe faceplate files are compatible with:RSLogix5000 V15 or laterRSView Supervisory Edition 4.0 or later.Before using faceplate files, please upgrade your RSView Studio Supervisory Edition Version 4.0 with the patches posted on or after 01/01/07.The latest RSView Studio Su

4、pervisory Edition 4.0 patches may be found within the Rockwell Automation Knowledgebase at the following website/ Answer ID: /knowledgebaseAnswer ID:35680NOTE: These instructions are for Distributed I/O on EtherNet/IP and ControlNet but not DeviceNet.The following mod

5、ules are compatible with these instructions.DigitalAnalog1738-I2M12AC31738-IE2CM121738-I2M12AC41738-IE2VM121738-IB2M121738-IT2IM121738-IB4M121738-IR2M121738-IB4M81738-OE2CM121738-IB8M231738-OE2VM121738-IB8M81738-IB8M121738-IV4M121738-IV8M231738-IV8M81738-IV8M121738-OA2M12AC31738-OB2EM121738-OB4EM121

6、738-OB8EM121738-OB8EM231738-OB8EM81738-OV4EM121738-OW4M121738-OW4M12ACGeneral Setup1) After downloading your file, the following folder will be created: SE_1738_Digital&Analog_Faceplate_Files. This file will contain all of the required files needed for configuring the 1738 I/O faceplates in your app

7、lication.Logix Configuration1) Open existing Logix file with RSLogix 5000For distributed I/O, ensure that the Communications adapter local to the controller has already been configured in the RSLogix 5000 I/O configuration.a. Right click on the local Communications adapter and select “New Module” to

8、 add the appropriate network adapter.b. Select the appropriate adapter module for the distributed I/O you are using (i.e. 1738-AENT).c. Give the new Adapter module a name, a description and enter the correct chassis size. For a 1738-AENT set the IP address.d. Right click the Adapter (i.e. 1738-AENT)

9、 module for the intended ArmorPoint I/O and select “New Module”. Then select the appropriate ArmorPoint I/O module.e. Enter a distinct module name and description.f. Repeat steps 2d-2e for all ArmorPoint I/O modules.RSView SE Configuration1) Open your existing RSView SE application that you wish to

10、add the ArmorPoint I/O faceplate to.2) Add the appropriate “SE_1738-Ixx_Faceplate.gfx” or “SE_1738-Oxx_Faceplate.gfx” file to your displaysa. Right-click on Displays, and select “Add Component Into Application”. Browse to the SE_1738_Digital&Analog_Faceplate_Files folder and select the faceplate GFX

11、 file that matches the module you wish to create a faceplate for.3) Add the faceplate parameter file “SE_1738_Parameter.par” to your RSView SE application.a. Right-click on Parameters, and select “Add component to application”. Browse to the SE_1738_Digital&Analog_Faceplate_Files folder and select t

12、he “SE_1738_Parameter.par” file. Then click the Open button.b. Now open the parameter file that you just added and edit the “parameter tagname” to match your application. The “parameter tagname” needs to include the RSLinx Enterprise “Device Shortcut” name of your systems controller and the Logix “t

13、agname” of the intended ArmorPoint I/O module to monitor.i. Double-click on the faceplate parameter file, and edit the “Device Shortcut” name, (in this example it is CLX-L43) to match the Logix controller that was previously configured in your RSLinx Enterprise Communication Setup.#1=:CLX-L43Network

14、_Adapter:1ii. Enter the desired Logix “tagname” of the intended Point I/O module to monitor.(For modules that are distributed, this tag name will be the name of the I/O adapter followed by a “:” and the slot location of the module, ie., Network_Adapter:1.) Close and Save changes.#1=:CLX-L43Network_A

15、dapter:1To add parameter files for additional Point I/O modules, simply repeat steps 3a and 3b above, creating a unique parameter name and assigning the associated “Device Shortcut” and Logix “tag name” for each module.Example: #1=CLX-L43Network_Adapter_2:1 (“Network_Adapter_2” represents another un

16、ique name for an I/O adapter on the network and “:1” represents the module in slot 1.)4) Create the display navigation to open the ArmorPoint I/O Faceplates at runtime.a. On a desired graphic display, create a new button object.on obb. Double-click on the buttject to display its properties and confi

17、gure the Action tab. Click onthe browse (i.e. ellipses,) button beside the Press Action field to launch the Command Wizard.c. Select the Display command and click Next.d. Use the browse buttons, drop down menus and the Parameter File checkbox to select the appropriate area, display and parameter file name and click Finish.e. The Display command syntax has now been configured and inserted into the Press Action field.f. C