2014版klari-fuse_2010_en_v1_W

1、KLARI-FUSE2KLARI-FUSE-2with FK1, FK2, FK3 and HI-ProbeStatus April 2009. All mentioned trademarks or brands are property of the corresponding owner. Subject to error and technical changes.DESCRIPTIONThe universal multi-channel millivoltmeter KLARI-FUSE has been developed for use in combination with

2、low- resistance measuring shunts to measure currents in various sections of a vehicles fuse box.At the front of the unit there are eight connectors with precision contacts using which the measuring adapters in the form of special measuring fuses can be connected. The inputs used for voltage measurem

3、ent are each electrically isolated.These connectors also have communication lines. They allow configuration data (such as measuring range, compensation values and so on) to be read out of the connected measuring adapters. The compensation values are taken into consideration when the measured values

4、are calculated. This results in a very high degree of accuracy.ACCESSORIESCurrent probes: To measure the current in defined electric circuits in vehicle fuse boxes, we offer adapters with FK1, FK2 and FK3 plug-in fuses.These adapters allow the measuring circuit to be protected in the ranges 5 to 70

5、A by the original fuse.The high-current probes cannot be protected by fuse as the measuring range goes up to 4800 A.We also offer voltage probes in the ranges 0 to 80 V. Our temperature probes have an integrated PT1000 sensor and are available as a standard and acid- resistant variant.POWER SUPPLY6

6、to 50 V DCExamples for Probe types, measuring ranges and resolutions (given in Gain 100):Probe typeMeasuring RangeResolution/BitResistorLI-Probe 1-0,3.+0,72A0,25 A1 LI-Probe 25 m-12+28,8A10 A25 mFK1 and FK2 10A+/- 10 A21 A12 mFK1 and FK2 20A+/- 20 A50 A5 mHI-Probe120A-300+720 A250 A1 mHI-Probe1200A-

7、3000+7200 A2,5 mA0,1 m*Factory calibration with certificate is available on request (subject to an additional fee).KLARI-FUSE-40 to +130CProbes:KLARI-FUSE: -40 to +85CTemperature range1 V/bit4 V/bit4 V/bit24 V/bitResolution: Resolution: Resolution:Resolution:Resolution: 250 nV/bitResolution: 500 nV/

8、bit+/-0 to 7.5 mV+/-0 to 15 mV+/-0 to 30 mV+/-0 to 120 mV+/-0 to 120 mV-300 to + 720 mV-Status April 2009. All mentioned trademarks or brands are property of the corresponding owner. Subject to error and technical changes.SPECIFICATIONSInputs Max. 8 channels for voltage measurement, potential-free f

9、or:- I probes- U probes and- T probes (PT1000)Resolution+/- 15 bit/measuring range 5 measuring rangesSampling ratesAdditional functions 1 Kanal max. 8000S/sec. 12 chanel max. a. 4000S/sec. 34 chanel max. a. 2000S/sec. 58 chanel max. a. 1000S/secOutputs Time synchronisation of several KLARI-FUSE unit

10、s via master/slave selection (CAN or RS232 interface) Isolated high-speed CAN up to 1 MBaud Terminating resistor can be switched and/or USB-2.0Time base 32,768 Hz resonator 30 s resolutionHousing (LxWxH) Metal housing: 170x115x50 mmPower supply 6 to 50 V DCPower consumption Approx. 200 mA at 12 V DC

11、ConfigurationOperating modes USB-2.0 , using supplied PC software KoWin or Klari-Toolbox 8-channel parallel operation- Autorange over all measuring ranges- Reduction of data rate by means of:- Differential measurement with adjustable value- Limit mode (measured values below the limit are not transmi

12、tted)Insulation voltage 80 V DCProtection class IP65APPLICATIONStatus April 2009. All mentioned trademarks or brands are property of the corresponding owner. Subject to error and technical changes.ITEMS SUPPLIED AS STANDARD KLARI-FUSE module, item no. IMFUS-00001-0000Probes have to be ordered separa