EPONV2R1常用命令.doc

1 安装ONULED 指示灯： 1) Power-长亮 2) Run-闪亮3) PON-长亮 (如果PON灯是灭的，请检查ONU处接收光功率)4) Link/Ack 长亮-用户电脑开机 闪亮-以太网端口收发数据 2 GFA6700的命令行帮助1) 输入 list string 命令查找关键字中包含某个字符串的命令，如 list mac EPON_V2R1(config)#list mac delete forward-entry drop mac H.H.H vlan vlanname delete forward-entry mac H.H.H vlan vlanname forward-entry mac H.H.H vlan vlanname slot/port 。 show onu information mac H.H.H show sysmacEPON_V2R1(config)#2) 输入一个关键字加空格后，可以输入“？”来查看以该关键字开头的所有可用命令，如 interface 空格 键入?， 提示如下： EPON_V2R1(config)#interface ethernet Config ethernet interface trunk Config Trunk interface vlan Config multicast vlan interfaceEPON_V2R1(config)#interface3) 输入部分关键字后，不加空格，直接键入?，可以列出所有以输入的字符串开头的关键字，如：interfa键入?,系统提示如下： EPON_V2R1(config)#interfa interface Select an interface to config4) 输入部分关键字后，不加空格，直接键入tab键，则系统自动补齐关键字的剩余部分，如果存在多个以已输入字符串开头的关键字，系统则列出所有可用关键字。如下所示： EPON_V2R1(config)#inte键入tab键EPON_V2R1(config)#interface EPON_V2R1(config)#onu键入tab键onu onu-pon onu-registerEPON_V2R1(config)#onu 3 EPON业务开通流程：1) OLT加电2) ONU注册ONU前面板的PON灯亮ONU的接收光功率范围要求(-8dBm到-24dBm)3) 使用串口线访问OLT(波特率9600) 使用命令show onu-list查看ONU列表 使用命令show online-onu查看的ONU4) 配置OLT上的VLAN业务 创建VLAN 添加端口5) 给OLT配置公网地址和默认网关 interface vlan manage ip address 00/24 exit ip route /0 546) 配置ONU的上下行带宽 onu downlink-policer pon 5/1 bandwidth class 2 delay low assured-bw 180000 best-effort-bw 180000 up 1 bandwidth class 2 delay low assured-bw 180000 best-effort-bw 180000 down 1 exit7) 配置ONU上的vlan业务 onu 5/1/1 vlan dot1q_add 100 vlan dot1q_port_add 100 1 2 vlan dot1q_port_add 100 3 1 exit8) 配置ONU上的端口限速 onu 5/1/1 port ingress_rate 1 0 8000 port egress_rate 1 8000 exit9) 保存OLT和ONU的配置 save onu 5/1/1 mgt config save exit 4 OLT 配置命令1 ) Vlan配置 interface vlan vlanname 1-4094*1 add port portlist tagged|untagged delete port portlist tagged|untagged ip address A.B.C.D/M undo ip address A.B.C.D*1 exit2) 网关设置 ip route /0 543) ONU 带宽设置 onu down-link policer pon 5/1 bandwidth class 2 delay low assured-bw 180000 best-effort-bw 180000 up 1 bandwidth class 2 delay low assured-bw 180000 best-effort-bw 180000 down 1 exit4) 以太网接口配置 Interface 1/1 Show Show statistics Clear statistics exit 5) ARP和MAC地址表操作 Show arp Clear arp Show forward-entry port|vlan|mac*1 pon 5/1 show fdbentry mac exit 6) SNMP网管命令 service snmp enable service snmp trap enable config snmp trapreceiver add 4 version v1 community public 7) 其它命令 Save Rebootconfig hostname GFA6700 show version show slot show system time set system time show onu-list show online_onu show onu-version pon 5/1 show onu-list show online_onu show onu-version update onu file exit download ftp app . olt|ONU) download ftp driver .dba|pas5001 show running-config (memory) show running-config interface vlan show config-file erase config-file erase alarm log user add|delete user role （only admin user have this right，and must login using a password) confiue login-authentication enable 5 告警1) ONU注册告警 2007-12-24,12:02:51 10mkr_dom17/1 first register 11404: 2008-08-20,01:49:35 V2R1-ONU-42003 not present: REPORT TIMEOUT11405: 2008-08-20,01:49:36 V2R1-ONU-42003 re-register 2) ONU 掉电告警 11433: 2008-08-20,01:53:07 V2R1-ONU-41002 power off 11435: 2008-08-20,01:53:21 V2R1-ONU-41002 power on3) ONU端口up-down告警 11415: 2008-08-20,01:51:38 V2R1-ONU-41002 interface eth1/2 linkdown11569: 2008-08-20,02:10:59 V2R1-ONU-41002 interface eth1/2 linkup4) 管理操作 11741: 2008-08-20,07:04:08 V2R1-ONU-42002 not present: OAM LINK DISCONN11742: 2008-08-20,07:04:33 V2R1-ONU-41002 not present: HOST REQUEST5) OLT 重启 11772: 2008-08-20,07:07:49 Epon V2R1 pon4/1 firmware load success11773: 2008-08-20,07:07:49 Epon V2R1 pon4/1 DBA load success 16437: 2007-12-24,10:24:00 Epon V2R1 cold start11780: 2008-08-20,07:08:17 Epon V2R1 OLT warm start 6) 相关命令show alarm logshow alarm log today/yestodayshow alarm log strat-time 2007-12-24,10：00：00show alarm log end-time 2007-12-24show alarm log strat-time 2007-12-24,10：00：00 end-time 2007-12-24show alarm log class 1-5sow alarm log trap 1-55show alarm log device 1show alarm log device 51001show alarm log onu 5/1/1show alarm log name EPONV2R1show alarm log name onuname 6 ONU配置1) GT811_A/G812_A(新款的ONU) Show device information device name 5/1/1-wensan3# Vlan dot1q 0|1 Vlan dot1q_add Vlan dot1q_port_add Vlan dot1q_show Port link_showPort mode Port mode_show Port ingress_rate port 0 0 （default ：8Mbps） Port egress_rate port 0 （default ：8Mbps） Stat port_show Stat port_flush Mgt config save Mgt config clear Mgt reset Mgt up-time 2) GT813配置Interface vlan V100 100vlan V100 add port 1taggedvlan V100 add port 26 tagged （uplink port）vlan v100 ip add 00/24vlan V100 delete port 1,2,5-24 taggedundo interface vlan V100show interface vlansave configurationerase config-fileshow device informationshow forward-entry mac vlanname port Flag Trunk DropFlag 0018.8B8D.B3B1 default 26 0050.DA6C.AB9F default 26 000C.F174.4242 default 26port 1 line-rate ingress cir 0 cbs 1000 （default ：no rate limit） port 1 line-rate ingress cir 0 cbs 1000 （default ：no rate limit） show port 1 Onu interface port 1 is up. Physical status is up, administrator status is up. MTU 1500 bytes. Port type is 100Base-TX. UrTypeName is FE. AutoNegotiation enabled. DIX encapsulation. Duplex full. FlowControl disabled. Hardware is ethernet. Trunk-Access-Mode is Access. Max speed 100 M, current speed 100 M, Bandwidth 100000 Kbits. Ingress line-rate cir 10000 cbs 1000, Egress line-rate cir 10000 cbs 1000. Accesslimit disabled. Be added into vlan(s): Vlan name:default, vlan ID:1 Onu port 1: In Rate(Last 2Sec):0 In Bytes :0 In Total Pkts :0 In Unicast Pkts :0 In Multicast Pkts :0 In Broadcast Pkts :0 In Pause Frames :0 In Discard Fr