土木工程专业毕业设计外文文献翻译2篇.doc_第1页
土木工程专业毕业设计外文文献翻译2篇.doc_第2页
土木工程专业毕业设计外文文献翻译2篇.doc_第3页
土木工程专业毕业设计外文文献翻译2篇.doc_第4页
土木工程专业毕业设计外文文献翻译2篇.doc_第5页
已阅读5页,还剩7页未读, 继续免费阅读

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

XXXXXXXXX学院学士学位毕业设计(论文)英语翻译课 题 名 称 英语翻译 学 号 学 生 专 业、年级 所 在 院 系 指 导 教 师 选 题 时 间 Fundamental Assumptions for Reinforced Concrete BehaviorThe chief task of the structural engineer is the design of structures. Design is the determination of the general shape and all specific dimensions of a particular structure so that it will perform the function for which it is created and will safely withstand the influences that will act on it throughout useful life. These influences are primarily the loads and other forces to which it will be subjected, as well as other detrimental agents, such as temperature fluctuations, foundation settlements, and corrosive influences, Structural mechanics is one of the main tools in this process of design. As here understood, it is the body of scientific knowledge that permits one to predict with a good degree of certainly how a structure of give shape and dimensions will behave when acted upon by known forces or other mechanical influences. The chief items of behavior that are of practical interest are (1) the strength of the structure, i. e. , that magnitude of loads of a give distribution which will cause the structure to fail, and (2) the deformations, such as deflections and extent of cracking, that the structure will undergo when loaded under service condition.The fundamental propositions on which the mechanics of reinforced concrete is based are as follows:1. The internal forces, such as bending moments, shear forces, and normal and shear stresses, at any section of a member are in equilibrium with the effect of the external loads at that section. This proposition is not an assumption but a fact, because any body or any portion thereof can be at rest only if all forces acting on it are in equilibrium.2. The strain in an embedded reinforcing bar is the same as that of the surrounding concrete. Expressed differently, it is assumed that perfect bonding exists between concrete and steel at the interface, so that no slip can occur between the two materials. Hence, as the one deforms, so must the other. With modern deformed bars, a high degree of mechanical interlocking is provided in addition to the natural surface adhesion, so this assumption is very close to correct.3. Cross sections that were plane prior to loading continue to be plan in the member under load. Accurate measurements have shown that when a reinforced concrete member is loaded close to failure, this assumption is not absolutely accurate. However, the deviations are usually minor.4. In view of the fact the tensile strength of concrete is only a small fraction of its compressive strength; the concrete in that part of a member which is in tension is usually cracked. While these cracks, in well-designed members, are generally so sorrow as to be hardly visible, they evidently render the cracked concrete incapable of resisting tension stress whatever. This assumption is evidently a simplification of the actual situation because, in fact, concrete prior to cracking, as well as the concrete located between cracks, does resist tension stresses of small magnitude. Later in discussions of the resistance of reinforced concrete beams to shear, it will become apparent that under certain conditions this particular assumption is dispensed with and advantage is taken of the modest tensile strength that concrete can develop.5. The theory is based on the actual stress-strain relation ships and strength properties of the two constituent materials or some reasonable equivalent simplifications thereof. The fact that novelistic behavior is reflected in modern theory, that concrete is assumed to be ineffective in tension, and that the joint action of the two materials is taken into consideration results in analytical methods which are considerably more complex and also more challenging, than those that are adequate for members made of a single, substantially elastic material. These five assumptions permit one to predict by calculation the performance of reinforced concrete members only for some simple situations. Actually, the joint action of two materials as dissimilar and complicated as concrete and steel is so complex that it has not yet lent itself to purely analytical treatment. For this reason, methods of design and analysis, while using these assumptions, are very largely based on the results of extensive and continuing experimental research. They are modified and improved as additional test evidence becomes available. 钢筋混凝土的基本假设作为结构工程师的主要任务是结构设计。设计是对一般的结构和特定结构等所有层面的一个具体的确定,使结构可以被安全地建造,并安全地承受的各种因素的影响,在它的整个使用寿命中能够很好的发挥作用。这些影响主要是来自承受的负载和其它受到的因素,以及其他有害的影响如温度波动,基础下陷的影响或是受到侵蚀的影响。结构力学是结构设计的主要工具之一,在这个设计过程中,要做一个良好的预测,得到结构变形的程度,能够及时的采取一定的措施去加固。在这个过程中要做的最重要的事是:(1)充分的研究这个结构,即能够得到这个结构所能承受的极限的结构荷载的大小和强度(2)还有就是变形,了解结构在承受荷载时变形的程度,出现裂缝的程度。以上所提到的钢筋混凝土的力学基础的基本主张是:1、内部力量,如弯矩,剪力,承受正常剪应力的任何一个结构部分,在受外部负载的影响时部分的结构是平衡的。这一主张不是一个假设,而是一个事实,因为任何机构或其任何部分在整个结构中受力都是平衡的。2、一个嵌入式钢筋的应变与外部具体是相同的。这是假设混凝土和钢筋之间存在完美结合,这样两种材料之间没有可能发生滑移。因此,一个构件在变形时,机械的连锁提供自然截面的附着力,所以是非常接近这个假设的。3、在截面那些负载装载之前,应继续在加载的负载。精确的测量表明,当一个钢筋混凝土构件加载接近失败时,这种假设并非绝对准确。但是,通常偏差是轻微的。4、在鉴于混凝土的抗拉强度比起其抗压强度差很多,在这一个构件中,肯定会存在裂缝,虽然这些裂缝在精心设计的构件中通常是难以见到。这种假设显然是实际情况比较简单,因为事实上,混凝土开裂之前,位于混凝土的裂缝处有抵制小幅度的拉应力。后来在钢筋混凝土梁的抗剪切的讨论中,这种特定的假设有一定的条件和优势是明显的,适当配合比强度的混凝土可以有发展的前景的。5、该理论是基于实际应力应变关系和两部分组成材料合理的组合产生的等效强度性能。理论的内容在实际生活中体现,将这两个材料联合使用比那些高弹性材料建造的结构的结构设计复杂得多也更具挑战性。这五个假设能预测一些简单的情况下钢筋混凝土构件。事实上钢筋和混凝土这两个中同样复杂的材料,在一起使用时不适于纯粹的分析处理。由于这个原因,在结构的设计方法和分析使用这些假设时,最主要的依据是广泛和持续使用的实验研究结果,这些修改和补充检验的理论可以使钢筋混凝土结构变得可以被使用。Development Tendency and Instructions of Civil EngineeringWith the progress in science and technology and engineering development of the practice of the disciplines of Civil Engineering has developed into a broad connotation, many categories, and the structure of complex integrated system. For example, on civil engineering projects built with the use of facilities in terms of functionality, and some interest for residential purposes;Some production activities; some for land, sea and air transport; some for water utilities; some as a tool for information transmission; some as a means of energy transmission and so on. This requires the integrated use of a variety of civil engineering material conditions in order to meet diverse needs. Civil Engineering has developed a lot of branches, such as housing projects, railway projects, road projects, airport projects, bridge projects, the tunnel and underground engineering, special engineering structures, water supply and drainage works, urban heating for the gas works, port works, water conservancy engineering sciences. Some of these branches, such as water conservancy project, because of their own projects targeted at the growing and specialized scientific and technological development have been divided out from the civil engineering disciplines as an independent system, but they are still largely in common with civil engineering. Civil Sociality are accompanied by the development of human society developed. It reflects the construction of engineering facilities in every historical period of socio-economic, cultural, scientific, technical development of the face, thus civil society has become one of the historical development of the witness. Ancient times, people will start to build simple houses, roads, bridges to meet the needs of easy living and production needs. Later, the people in order to adapt to the war, production and dissemination of religious life and the needs of the construction of the city, canals, palaces, temples and other buildings. Many well-known works shown in this historical period of human creativity. For example, Chinas Great Wall, Du Jiang Yan, the Grand Canal, Zhao Zhou Bridge, Ying Xian Wooden Tower, Egypts pyramids, the Greek Parthenon, Romes water supply engineering, coliseum amphitheater (Rome large bucket beast field), as well as many other well-known churches, palaces and so on. After the industrial revolution, especially to the 20th century, on the one hand, civil society to put forwards a new demand; on the other hand, are all areas of society for the advancement of Civil Engineering has created favorable conditions. Such as building materials (steel, cement) implementation of industrial production, machinery and energy technology, and design theory of progress are provided for the Civil Engineering Materials and technical assurance. Thus this period has been rapid development of civil engineering. Emerged around the world at large-scale modernization of industrial plants, skyscrapers, nuclear power plants, highways and railways, large-span bridges, large-diameter pipelines, long tunnels, the Grand Canal, big dams, big airports, major seaports and marine engineering and so on. Modern civil society continue to create for mankind a new physical environment, human society and modern civilization has become an important part.Practical Civil Engineering is a highly practical subject. In the early days, through the Engineering Practice of Civil Engineering, sum up successful experiences, especially the lessons learn from the failure of developed. From the beginning the 17th century to Galileo and Newton as the forerunner of modern mechanical and civil engineering practice, and has gradually formed material mechanics, structural mechanics, fluid mechanics, and rock mechanics, as the basic theory of civil engineering disciplines. This Civil Engineering from the experience gradually developed into a science. Civil Engineering at the development process, engineering practice and experience often first in theory, works often show that the accident was unable to foresee that the new factors, triggering a new theory of the research and development. So far, many works deal with the problem, is still very much rely on practical experience. The reason why the development of civil engineering technology major with engineering practice rather than by virtue of scientific experiments and theoretical studies, there are two reasons: First, some of the objective situation is too complicated, it is difficult to faithfully carry out laboratory or field testing and theoretical analysis. For example, ground-based foundation, tunnels and underground engineering stress and deformation state and its changes over time is still necessary to refer to an analysis of engineering experience to judge. The second is only for new engineering practice in order to reveal new problems. For example, the construction of a high-rise building, high-rise tower mast and large cross-bridges, the wind resistance and seismic engineering highlighted the problem in order to develop this new theory and technology. Technically, economically as well as building up the unity of the arts people seek the most economical to build an engineering facility is scheduled to meet the needs of users, including the aesthetic requirements. While a project is economic and technical activities are closely related. Projects economic performance at the outset of the project site, on the overall planning, followed by performance at the design and construction technical. The total investment for project construction, the project is completed after the period of economic efficiency and the use of the maintenance costs are measured works of an important aspect of the economy. Close contact that these technical issues, be considered. Meet the functional requirements of civil engineering facilities as a space for art, first and foremost through the overall layout of the body itself, the various parts of the size of the ratio of lines, colors, light and shade and the shadow of the surrounding environment, including its coordination with the natural harmony manifested; followed by the adoption of the Additional engineering facilities in the local decorative reflected. Engineering facilities and decorative shapes can also show places style, ethnic style and time style?Civil Engineering at the long-term practice, people not only to the building housing the arts to give considerable attention, and achieved outstanding success; but also for other engineering facilities, but also through the choice of different building materials, such as the use of stone, steel and reinforced concrete, with the natural environment built on very much in the art is beautiful, functional works also very good. Ancient China the Great Wall, much of the modern world on TV and oblique Zhang bridges, are examples in this regard. Civil Engineering is the construction of various projects and facilities, collectively referred to science and technology. It refers to the application of materials, equipment and carried out the investigation, design, construction, maintenance and other technical activities; also refers to the construction of the object, that is built on the ground or underground, on land or water, directly or indirectly, for human life , production, military, scientific research services for a variety of engineering facilities, such as housing, roads, railways, pipelines, tunnels, bridges, canals, dams, ports, power plants, airports, offshore platforms, water supply and drainage and protection works. Construction material and engineering facilities are basic land, building materials, construction equipment and construction machinery. With these material conditions, economic and convenient built to meet the people can use requirements and aesthetic requirements, but also to tolerate the various loads security engineering facilities, civil engineering disciplines are the starting point and destination. Civil Engineering and three times in the history of the leap Of Civil Engineering play a critical role in the development of, first of all, as are the material foundation for the civil engineering building materials, followed by the subsequent development of design theory and construction technology. Whenever there is a fine new building materials, the Civil Engineering will have leap-type development. People at an early stage can only depend on the soil, wood and other natural materials to create engaging activities, the subsequent emergence of such artificial brick and tile building materials, so that the first human to break the shackles of natural building materials. Chinese in the eleventh century BC and the early Western Zhou Dynasty to create the tile. The first brick in the fifth century BC to the third century BC, when the tomb of the Warring States Period. Brick and tile soil better than mechanical properties, can local materials, and easy to manufacture. The appearance of brick and tile people begin extensive and substantial in construction of housing and urban flood control projects. This civil engineering technology has been rapid development. Up to 18 19 century, at up to two thousand years, brick and tile has been a civil engineering building materials essential for the human civilization has made a great contribution, and even at present is also widely used. Steel substantial civil engineering applications are the second leap. 70s start the seventeenth century the use of pig iron, the beginning of the nineteenth century the use of wrought iron construction of bridges and housing, steel this is a prelude to appear.From the beginning the middle of the nineteenth century, metallurgical industry, smelting and rolling out of high tensile and compressive strength, ductility, and the quality of uniform building steel, and then produce high-strength steel wire, steel cable. Therefore necessary to adapt to the development of the steel structure has been booming. In addition to the application of the original beam, arch structures, the new truss, frames, grid structure, gradually extended the suspension structure, a structural form flowers Zhengyan situation. Building long-span structures from brick, stone structure, wood structure a few meters, the development of tens of meters to 100 meters of steel structures, a few hundred meters until 1000 meters above modern. So at Dajiang, both shelves starting Bridge, starting at the ground on the construction of skyscrapers and high-rise tower, and even laying on the ground under the railway, to create an unprecedented miracle. In order to meet the needs of the development of steel structure engineering, at the basis of Newtons mechanics, material mechanics, structural mechanics, structural design works on the theory came into being. Construction machinery, construction technology and construction organization design theory also the development of civil engineering rose from experience become a science, in engineering practice and the basic theories have taken on a new look, which led to more rapid development of civil engineering. The nineteenth century, 20s, made of Portland cement, the concrete had come out. Concrete aggregate can be local materials, ease of molding concrete structures, but the tensile strength of concrete is very small, uses are restricted. After the mid-nineteenth century, iron and steel production surged, with the attendant emergence of this new type of reinforced concrete composite building materials, which bear the pulling force of reinforced concrete to bear the pressure to play their respective advantages. Since the beginning of the twentieth century, reinforced concrete is widely used in civil engineering fields. Start from the thirties, there has been pre-stressed concrete. Prestressed concrete structures crack resistance, stiffness and load-bearing capacity, much higher than the reinforced concrete structure, which uses an even wider area. Civil Engineering into the reinforced concrete and prestressed concrete dominant historical period. Give the

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论