AB 触摸屏中文文本显示.doc

1. 首先，如果使用的是FT6.0以上的人机界面软件，就必须通过U盘或者CF卡将字库文件拷贝到触摸屏中。如何拷贝呢？您需要在U盘（有时会不认U盘，请多试几个U盘）或者CF卡中根目录下建立一个名字为”Fonts”的文件夹，然后将字库文件拷贝到这个目录下，然后插入人机界面后面的插口中。在人机界面中，点击“Terminal Settings” - “File Management” - “Copy Files” - “Copy Fonts” - “External Storage 1/2” - 选中字体文件，然后选择“Destination”是 ”Internal Storage”.2. 在Rsview Studio中下载字库simsun_2_50.ttc到PVC， 3. 在Configuration Mode, 进入 Terminal Settings/Font Linking. 4. 发现列表中Arial font. 5. 点击 Show Links 键. 6. 点击 Edit Link 键. 7. 浏览 main font, 在列表中选择Simsun. 8. 点击 Add Font 键. 53463 - Max PanelView Ethernet Connections to MicroLogixHow many PanelView Standard / PanelView Plus / PanelView Componentcan be connected to the Ethernet port of a MicroLogix controller?While the practical limit is two PanelViews per MicroLogix 1100, it is possible to go up to:3 PanelView Plus connected to the ML1100. This is due to the connection limitations. Each PanelView Plus can potentially use five connections. The MicroLogix 1100 supports 16 incoming connections and 16 outgoing connections.3 PanelView Standard will work just fine with the Ethernet port on the ML1100. PanelView Standard can use up to four connections. Although you can use up to four PV standard, if you use all four, you will not be able to get online via Ethernet as all of the possible connections would be used.The PanelView Component consumes one Ethernet connection, but the practical limit is 2:1: 2 PVc per MicroLogix 1100 2 MicroLogix 1100 per PVc63165 - PanelView Plus Compact Machine Edition Applications LimitationsWhat are PanelView Plus Compact Machine Edition Applications Limitations?Compact Machine Edition ApplicationsCompact Machine Edition applications are applications intended to run on the PanelView Plus Compact terminal.Compact Machine Edition applications have the following restrictions: Amaximum of 25 displays. Amaximum of 200 alarm messages. Amaximum screen resolution of 640x480. Only available in 4, 6, and 10 screen sizes. Only one RSLinx Enterprise shortcut; if no RSLinx Enterprise shortcut is defined, a single KEPServer Enterprise data server can be used to communicate with a single device.o The Kepware Hilscher Universal and Modbus Plus communications drivers are not supported for PanelView Plus Compact terminals. Only serial and Ethernet communications; if the application uses RSLinx Enterprise, only Serial-DF1, Serial-DH485 and Ethernet drivers are supported. Only RSLinx Enterprise version 5.20 or later and FactoryTalk View Machine Edition version 5.1 or later supported. FactoryTalk ViewPoint not supported.55149 - How to use Global Connections Current Screen Number for PLC screen navigation on the PVc?Howcan the PLC cause the PVc to change screens?Assign a external tag to the read and write fields in Tags/Global Connections tab.At runtime the PVc will write the current screen number to the write tag (Destination Tag ) in the PLC.The PVc will read from the read tag( Source Tag ) which willallow the PLC to control screen changes.The operator does not have control over screen changes until the read tag has a value of 0 (zero). Please allow time for screens to draw on screen changes before changing again.21321 - How to change screens in RSView Machine Edition from a remote location.Application Note:To change to a specific screen from a remote PLC, a tag must be selected in the Global Connections / Remote Display Number field. A (screen) number, written to this tag, will initiate the change to the appropriate screen. The number of the active screen will be reflected in the tag assigned to the Display Number field.The value of the Display Number field can be used as an acknowledgement to the PLC.Additional Notes:If a value other than 0 is left in the Remote display number field, manual changing of screens will not be possible, the PLC will maintain control of screen changes. If manual screen changes are desired along with PLC control, the value of the Remote display number field must be reset to 0. This can be done by writing a 0 to the tag from the PLC after an acknowledgement of a screen change. Another method could be to use a startup macro for each display that resets the Remote display number tag to 0.If using a pushbutton from an HMI to change screens, there will be an additional 1 second delay. (approx.)Only Replace type d