玩具制造业术语.docx_第1页
玩具制造业术语.docx_第2页
玩具制造业术语.docx_第3页
玩具制造业术语.docx_第4页
玩具制造业术语.docx_第5页
已阅读5页,还剩8页未读 继续免费阅读

下载本文档

版权说明:本文档由用户提供并上传,收益归属内容提供方,若内容存在侵权,请进行举报或认领

文档简介

塑胶玩具 hard toy/ plastic toy 电子玩具 electric toy 布料玩具stuffing toy/soft toy 独立装 individual pack 混合装assortment pack 外箱 shipping carton/outer carton 内箱 inner carton 内托 insert彩盒 gift box/printed box 索带plastic tie 扎带 wire 挂钩j-hook 挂钩贴 j-hook sticker 蝴蝶孔 butterfly hook 警告书 warning sheet 说明书 instruction sheet 吸塑装 blister pack收缩胶袋装 shrink wrap pack 玻璃窗彩盒装 window box pack 开放式彩盒装 display box pack 多种语言包装 multi language 两种语言包装 bilingual pack 吸塑罩/磁白内托 blister 吸塑卡blister card 无功能 non function 功能不良 poor function 间隙性无功能 intermittent function 不能保持位置 cannot hold position转动不顺 cannot free rotate 不能移动 cannot move 不能开动 cannot turn on 不能关闭 cannot turn off 不能发射 cannot shooting 利边 sharp edge 利角 sharp point 细小物件 small part 漏电 electric leakage棉花外露 stuffing expose 外来昆虫 foreign insect 摩术贴脱下 velcro detach 布料松 fabric loosen 电池发热 battery over heat 无声 no sound 细声 small sound 杂声 noise 大声 sound too loud 异声 abnormal sound 接触不良 poor contact 短路 short circuit电池弹簧突出 battery spring expose 电池弹簧松 battery spring loosen 电池弹簧甩 battery spring come off 电池片生锈 contact plate rust 电池片外露 contact plate expose 电池片甩 contact plate come off电池片松 contact plate loosen 电线突出 wire expose 电线甩 wire detach 电线焊接不良wire poor soldering (wire poor welding)开关无功能 switch non function 开关间隙性无功能Switch Intermitted Function 开关不良 Poor Switching 电路板坏 Circuit Board Damage 电路板松 Circuit Board Loose灯泡无光 Light Bulb Without Light 焊锡不良 Poor Soldering 螺丝未上紧 Screw Unfasten 螺丝上太紧 Screw Too Tight 螺丝生锈 Screw Rust合金有冷纹 Die-Cast Cold Mark 牙松 Gear Loosen 滑牙 Gear Slip 螺丝起子锋 Screw Flash 合金压炼不良 Poor Die-Casting 混色 Contamination Mark 削痕 Cut Mark 擦花 Abrasion Mark 刮花 Scratch Mark 凹痕 Dent Mark 顶针位 Ejector Mark 烧焦 Burn Mark 外来杂物 Foreign Materials 外来液体 Foreign Liquid 流水痕 Flow Mark 流水纹 Flow Line 折痕 Fold Mark 折纹 Fold Line 水印 Water Mark 批锋 Excessive Flash发白 White Mark 顶白 Stress Mark 水口 Gate缩水 Shrinkage 机油 Grease Mark 油渍 Oil Mark 污渍 Dirty Mark 胶水渍 Glue Mark 胶水多 Glue Over (Over Glue) 胶水少 Not Enough Glue 胶水雾气 Glue Gassing 装配不良 Poor Assembly 装配错误wrong Assembly 夹模线移位 Part Line Misalignment 夹模线 Part Line水口未清 Gate Remnant 胶丝 Plastic Residue 溶合不良 Poor Hot Melting 溶剂印 Solvent Mark 热贴不良 Poor Heat Sticking 透明度不良 Poor Transparency 热烫不良 Poor Hot Stamp 气泡(压炼) Air Bubble 压炼不良 Poor Molding Condition植毛不良 Poor Flocking 沙梨皮(搪胶) Pear Skin 钳痕 Clamp Mark 屈曲 Bent 烂 Broken 裂 Crack 穿孔 Void凹印 Sink Mark 太硬 Too Hard 太软 Too Soft 脆 Brittleness 走料不足 Under Shot 走料不到 Short Shot摇模件(厚薄不均) Uneven Wall Thickness 离隙 Gap On飞油/喷油过多 Over Spray 喷油水渍 Water Stain Mark 喷油不足 Under Spray 喷油不帄均 Uneven Spray 喷油不良 Poor Spray 喷油表面刮花 Scratch Painting 喷油表面粘尘 Dust Painting 外来油污 Foreign Paint 喷油反底 Paint Insufficient Coverage喷油擦花 Paint Abraded 喷油拖花 Paint Smear 漏喷油 Missing Painting 甩油/起皮 Painting Peel Off 橙皮油 Orange Peel 聚油 Paint Accumulation 力架聚油 Lacquer Accumulation 喷油哑色 Paint Color Dull 喷油颜色不对称 Paint Color Mismatch 喷油颜色有差别 Paint Color Different喷油颜色有光泽 paint color shine 喷油表面不光滑 rough surface 油料深色 dark paint 油漆喷涂不良 poor painting 油漆外层不良 poor coating 印油过多over print 丝印不良 poor silk screen printing 印油不足 under print 印刷不良 poor print 喷油表面起泡 bubble paint 补油不良 poor re-paint 移印油过多 over tempo 移印油不足 under tempo 电镀不良 poor electro-plating 、移印位置不正确 tempo painting dislocate 移印不完整/缺油 incomplete tempo painting移印颜色不同 tempo painting mismatch 移印不清楚/朦 tempo illegible 移印套色偏位 tempo painting offset 移印刮花 tempo scratching 漏移印 missing tempo 热烫过多 over stamp 热烫不足 under stamp电镀过多 over electro-plating 电镀不足 under electro-plating 电镀不良 poor electro-plating 电镀过黄 electro-plating yellow mark 电镀脱落 electro-plating peel off电镀擦花 electro-plating abraded 电镀成彩虹印 electro-plating rain mark电镀阴阳色 electro-plating shadow mark 电镀发黑 electro-plating black mark氧化 oxidation 吸塑不良 blister poor heat seal 吸塑无粘 blister unseal 吸塑烂 blister damage 吸塑裂 blister crack 吸塑压凹 blister crushed吸塑烧焦 burn mark on blister 吸塑变形 deformation on blister 吸塑不对 blister incorrect 吸塑脱落 blister detach 吸塑走料不到 blister undershot 吸塑卡皱 wrinkle on blister card吸塑卡烂 damage on blister card 吸塑卡擦痕 scratch mark on blister card吸塑卡裁剪不良poor die-cut on blister card 吸塑卡裁剪错误wrong die-cut on blister card 吸塑卡烧焦 burn mark on blister card 吸塑卡湿 wet on blister card 吸塑卡朦 illegible on blister card 吸塑卡不对 incorrect blister card卡纸内层分离 delamination on blister card 胶袋烂/穿孔 polybag damage 胶袋缩水 polybag shrinkage 胶袋走料不到 polybag undershot胶袋裁剪不良 poor die-cut on polybag 胶袋裁剪错误 wrong die-cut on polybag挂钩烂 j-hook damage 挂钩皱 j-hook wrinkle 挂钩内层分离 j-hook delimitation 挂钩胶贴移位 j-hook sticker dislocate挂钩胶贴击起 j-hook sticker expose (expose on j-hook sticker) 挂钩裁剪错误 j-hook wrong die-cut挂钩裁剪不良 j-hook poor die-cut 蝴蝶孔内层分离delamination on butterfly hook蝴蝶孔裁剪不良poor die-cut on butterfly hook 蝴蝶孔裁剪错误wrong die-cut on butterfly hook蝴蝶孔烂 butterfly hook broken 蝴蝶孔皱 butterfly hook wrinkle彩盒未封口 gift box unseal 彩盒压烂 gift box crushed 彩盒压变形 gift box deform 彩盒皱 gift box crumple 彩盒折痕gift box fold mark (fold mark on gift box)彩盒朦 gift box illegible 彩盒湿 gift box wet 彩盒粘位爆口 gift box flap open彩盒胶窗烂 broken on window box film 彩盒胶窗顶白stress mark on window box film彩盒胶窗透明度不良poor transparent on window box 彩盒胶窗有凹痕 dent mark on window box彩盒胶窗甩 detach on window box film 彩盒胶窗粘合不良 poor gluing on window box film胶纸粘不良 poor sticking on tape 超声不良 poor sonic weld 超声压花nest mark日期印朦 date code illegible 漏日期印 missing date code printing漏附件missing component 漏装配件 missing parts 胶纸用错 incorrect polybag 热封不良 poor heat sealing 贴纸翘起 label peel off 箱唛朦 shipping mark illegible 说明书朦 instruction sheet illegible 漏整包配件missing whole pack off accessory螺丝甩 screw came off 擦花 abrasion mark 混点 mottle mark 甩掉 came off 削痕 cut mark 刮花 scratch mark 涂油 paint 印刷 print 电镀 plate 补油 re-paint 超声 sonic 转动 rotate 溶剂 solvent走料不足 short shot 缩水 shrinkage 顶白 stress 前 front 后 rear 左 left 右 right 顶 top 底 bottom 底下 base 焊锡 solder 橡筋 elastic 漏电/水 leakage 荧幕 screen 电线 wire 线 thread 焊接 weld 黏合 seal 断电路 short circuit 黏 stick 不对称 uneven 魔术贴 velcro 未清 remnant 残余 residue 声音 sound 大声 loud 杂声 noise 车缝 sewing 缝(线)口seam 入棉 stuff 形状 shape 软 soft 丝 silk 斑点 spot 太过 too 布烂 torn 打磨/修饰 trim 不修饰 unmodified 摄/捆 trap 穿孔 void织结构 texture 铁轴 shaft 轮轴 axle 铰链 hinge 损坏 damage 顶针 ejector 磨擦 abrade 子口位 allowance 气泡 bubble 烂 broken爆裂击出 burst 灯泡 bulb 裂 crack 混杂 contamination 钳 clamp 外层 coat 接触 contact 电路 circuit 分离 delamination 合身 fit 比例 disproportion 散口 fray 电池线圈发热 battery coil over heat批锋 flash mark 滑牙 gear smooth 不能开 cannot open 不能关 cannot close不能滚动 cannot free roll 轮子转动不顺 cannot free wheel不能旋转 cannot rotate 车轮卡住不转 wheel stuck 喷油有尘点 dust paint成品太光滑 glossy finishing 移印移位 tempo off position 油污 paint smear喷油起泡 bubble paint 哑色 not enough gloss 颜色光亮 shine color 甩色 color migration 颜色沉 dull color 碎、变形 crush 毛公仔 plush 布公仔 soft toy 公仔衫湿 outfit wet公仔衫缩水 outfit shrinkage 公仔衫褪色 outfit fade 剪裁不良 poor cutting 形状不对称 uneven shape 车缝不良 poor sewing 缝合不良 poor stitching 车缝太密 high dense stitch 缝口爆口 seam open 跳针 jumping stitches 缝口子口外露 seam allowance expose车骨不良 poor narrowing 针孔 stitching hole 漏车骨 missing narrowing 缝边皱起 pucker 公仔衫不合身 outfit unfit 衣车靴痕 sewing machinery mark绣织花不良 poor embroidery 线未剪 untrimmed thread 长线 long loose thread唛头甩 sewing label loosen 物料走纱 materials run 物料烂 materials torn 入棉过多 over stuffing 入棉不足 under stuffing 入棉形状不良 poor stuffing 入棉比例不对称 stuffing expose 棉料外露 stuffing expose 长毛夹于缝口 pile trapped by seam长线夹于缝口 thread trapped by seam 长毛脱落露底 bald spot on plush脱色(经磨擦) color migration (颜色迁移) 不配色color mismatch 颜色有差别 color deviation 豆袋公仔 bean bag toy 织维散口 fabric fray 线带散口 ribbon fray 物料散口 materials fray 织毛不良 poor hair styling 梳发不良 poor brushing 剪头发不良 hair poor cutting发型不良 poor hair styling 熨画不良 poor hot stamping 布料组织不对 fabric texture mismatch彩盒装 gift box pack 有口彩盒装 display box pack 铁线扎带 cable tie 故事书 story book 车缝 machine sewing 手缝 labor sewing 胶袋装 bulk pack 擦油 abrasion 界油 adhesion 冲沙 sand flushing 干擦布 dry crocking 湿擦布 wet crocking 手洗 hand wash 变形 deform 不正确 incorrect 杂声 abnormal sound 其中某一功能不良 mal function 公仔衫 outfit 胶水飞扬 gassing 喷油表面不光滑 rough surface 压凹 crush 弄皱 crumple 凹 dent 过多 excessive 不定 insufficient 等份 halve 发热 heat 在彩盒上有外来贴纸foreign tape sticking on color box漏环保贴纸 missing recycle symbol label 镜面贴纸严重飘起 mirror label peel off seriously在盘子上漏黏胶纸 missing tape on tray 彩盒上漏版税贴纸missing royalty label on printed box 彩盒黏胶水不良超过2poor gluing on box more than2 包装未封口 package not sealed 彩盒上的贴纸损坏 tape on color box broken 单个陈列盒子 individual display box彩盒独立混装 individual game boxes 入卡通箱的包装方式manner of packing into carton box外箱烂导致包装成品外露 carton box damage such as damage inner package or products不够数量(每箱6pcs)shorting of quantity (6pcs per carton) 印刷移位超过1mm painting is deviated more than1mm印刷移位在0.5至1mm间 painting is deviated between 0.5mm and 1mm印刷颜色花样明显与标准办不符 uneven color difference or stain is remarkably different from the standard sample印刷表面的颜料明显与标准办不同coating of printed surface is remarkably different from the standard sample包装损坏长度超过10mm package damage defect length more than 10mm 漏装保证卡 missing warranty 配件拉甩 parts pull-off 混装比例错误 wrong assortment ration 危险的物体 dangerous object 螺丝松转动360 screw in loose or not enough tightened and turns more than 360dergrees 螺丝头有利角利边存在 slot in the screw head is damaged so that it way evaluated sharp point or sharp edge螺丝松可扭至180至360之间但对功能及其它质量无影响 screw is loose or not enoughtightened and turns between 180and 360degress without any effect for functional or other quality参照附页as per attached sheet 包装类型 packing type 漏水 leakage of water透明身内有杂物 litter inside clear body 底座离隙 gap on base 底座烧伤 burn mark on base 投箱后配件甩出parts came off after carton drop 身底座损坏 damage on lower body 透明身夹水纹 wrinkle mark on clear body按动按掣后头不能完全转动head cant return completely 透明身内披锋 flash on gate of clear body 漏锅钉 missing rivet橡皮盖损坏 rubber cap damaged 漏支座 missing feet漏塑料盘子 missing plastic plate 产品参照签办compare product with sign sample底座损坏或污秽 base damaged or soiled 漏一个或更多 missing one or more seam突出物 projections 弯曲试验 flexure 压力 compression胶袋和薄膜 plastic bags and films 脸 face 前额 fore head 太阳穴 temple 鼻子 nose 眼睛 eye 鼻孔 nostril 面颊 cheek 须 moustache 嘴 mouth 嘴唇 lip 颏/下巴 chin 胡子 beard 喉咙 throat 颌 jaw 颈/脖 neck 耳 ear 颈背 nape of the neck 耳垂 ear lobe头发 hair 腋窝 arm pit 胸部 chest 肚脐 navel 手臂 arm上臂upper arm 肘 elbow 前臂 fore arm 人体 the human body 臀部 buttocks腿 leg 肩 shoulder 股thigh 胚 shin 舌 tongue牙 tooth(the teeth) 踝 ankle 脚跟 heel 足底弓 arch 脚掌 sole 脚背 instep 脚趾 toes 趾甲 toe-nail 大脚趾 big toe 眼球 eyeball 眼眉 eyebrow 上睫毛 upper eye lashes 膝 knee 下睫毛 lower eye lashes瞳孔 pupil 眼睑 eye lid 结 knot 指纹 finger print 指甲油 nail polish 短上衣 jacket 衣领 collar 衬衫shirt 女裙 skirt 外套 sports jacket 钮扣 button 袖口 cuff 钮扣孔 button hole 袖子 sleeve 翻领 lapel 领带 tie 蝴蝶结 bow 蝶形领结 bow-tie 手拉手 hand in hand 臂挽臂 arm in arm双手叉着腰 arms akimbo 双臂合抱 arms folded 合金 die-cast 裁片 die-cut 外层 coat 梳发 brush 秃露 bald 裂 crack 不均衡 disproportion 图案或贴纸不标准decal or label not per specification卡通印唛不标准marking on carton not per specification盲孔(闭孔) blind hole 银线(银纹) silver line 无光泽/磨砂 frosting 帄滑面 slip plane外壳(面板)有油 oil on panel 变白 bleach (or whiten) 打磨(磨光)不良 poor polish (or furbish)定位螺丝缺胶水fixing glue on earth screw missing轴不够紧或太紧 bushing for attachments not tight or excess tight 手柄不能锁住locking handle does not latch 液体漏出 liquid leakage 金属片氧化/生锈metal contact plate was oxidation/rust内部塑胶件碎裂crack on internal plastic parts 内部塑胶件被打碎internal plastic parts was broken附件及配件上有裂痕cracked mark on enclosure and accessary附件上漏丝印/螺钉missing silk screen printing/screw on enclosure 轴尺寸不正确shaft dimension not per specification电池按钮不回弹 battery button no repercussion 漏生产源地 missing country of origin介子扣松 rotor locked loosen 出气口塞住 steam output hole blocked手柄锁住不能回弹locking handle does not repercussion卡通没打胶带 no plastic strap on carton (版权)保证卡 warranty card主要部份或其它配件main unit and other parts 说明书 instruction sheet 一直使用旧卡通箱唛 still use the old carton shipping mark箱号乱 carton number intricate 彩盒的认可标记错(如“ul”“bs”等)wrong approval marking on gift box (e.g.brand name ul. Bs etc)彩盒图案不清 decal illegible on color box盒边封两条透明胶纸each end of the printed box must be sealed by two transparent tape胶袋无警告字句及打4个孔polybag not warning word and punch 4 holes 产品用错料using not approved materials on product漏保证卡/警告语/说明书/价格贴纸/环保贴纸/维修保养清单/插页/ missing guaranteecard/warning/instruction book / rating label / recycle label / service list / insert card吸塑

温馨提示

  • 1. 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
  • 2. 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
  • 3. 本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
  • 4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
  • 5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
  • 6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
  • 7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

评论

0/150

提交评论