TD跨RNCKPI问题总结.doc

跨RNC KPI指标问题处理总结1、 问题处理思路：2、 Checklist参数检查2.1检查跨RNC的攻关参数动作描述处理方法说明传输配置检查检查2个RNC间的IPPATH和路由配置是否正确，且双向配置是否正确：ADD IPPATH: ANI=1990, PATHID=1, PATHT=HQ_QOSPATH, IPADDR=10.10.10.49, PEERIPADDR=10.10.10.57, PEERMASK=255.255.255.255, TXBW=50000, RXBW=50000, CARRYFLAG=NULL, FPMUX=NO, BWDCONGBW=0, BWDCONGCLRBW=0, VLANFLAG=DISABLE, PATHCHK=DISABLED;需要产品确认IPPATH和IP route配置是否正确、完整？定时器参数设置SET STATETIMER: RELOCCMDTMR=20000, RELOCIURELCMDTMR=60000, RELOCDATAFWDTMR=20000, RELOCANOTHERTMR=10000, RELOCCOMMITTMR=20000, RELOCMOBILCONFTMR=5000, RELOCPHYCHRECFGTMR=10000, RELOCUTRANHOCMPTMR=5000, RELOCFAILIURELCMDTMR=10000;RNC参数开关SET CORRMALGOSWITCH: HOSWITCH=PS_3G2G_CELLCHG_NACC_SWITCH-0&PS_3G2G_RELOCATION_SWITCH-0;RNC间小区邻区参数检查MOD NCELL: CELLID=12346, PLMNMCC=460, PLMNMNC=00, RNCID=1163, NCELLID=21346, READSFNIND=TRUE, BATONHOSUPPORT=ALL_SUPP, NCELLTYPE=FALSE;将跨RNC所有小区的硬切换改为接力切换。跨RNC小区支持接力切换（READSFNIND=TRUE、BATONHOSUPPORT=ALL_SUPP），非同覆盖小区（NCELLTYPE=FALSE）。NRNCCELL参数ACTTIMEDEFOFF=80MOD NRNCCELL: PLMNMCC=460, PLMNMNC=00, NRNCID=1163, NCELLID=21346, ACTTIMEDEFOFF=80, ACTTIMEDEFOFFFORHHO=100, QRXLEVMIN=-103, HSDPAALLOWED=ACTIVE, MIDDLERATERLACTTIMEDEFOFF=80, HIGHRATERLACTTIMEDEFOFF=80, OAMGUARDVALFORLOWRATE=200, OAMGUARDVALFORMIDRATE=200, OAMGUARDVALFORHIGHRATE=200, ACTTIMEDEFOFFVALFORUNCELLNOH=100, ACTTIMEDEFOFFVALFORUNCELLH=100, ACTTIMEDEFOFFVALFORSAMECELL=80, SUPPDPCMODECHGFLAG=FALSE, OVERLAYMOBILITYFLAG=FORBIDDEN, USEOFHCS=NOT_USED;ACTTIMEDEFOFFFORHHO=100QRXLEVMIN=-103HSDPAALLOWED=ACTIVEMIDDLERATERLACTTIMEDEFOFF=80HIGHRATERLACTTIMEDEFOFF=80OAMGUARDVALFORMIDRATE=200OAMGUARDVALFORMIDRATE=200OAMGUARDVALFORHIGHRATE=200ACTTIMEDEFOFFVALFORUNCELLNOH=100ACTTIMEDEFOFFVALFORUNCELLH=100ACTTIMEDEFOFFVALFORSAMECELL=80SUPPDPCMODECHGFLAG=FALSEOVERLAYMOBILITYFLAG=FORBIDDENUSEOFHCS=NOT_USED所有跨RNC小区的CELLRLACTTIME参数据HONULLACTTIMESWITCH=OFFMOD CELLRLACTTIME: CELLID=21346, ADAPTIVEALGOSWITCH=OFF, ACTTIMEDEFOFFVALFORSAMECELL=80, HONULLACTTIMESWITCH=OFF, ACTTIMEDEFOFFVALFORUNCELLNOH=100, ACTTIMEDEFOFFVALFORUNCELLH=100, OAMGUARDVALFORLOWRATE=200, OAMGUARDVALFORMIDRATE=200, OAMGUARDVALFORHIGHRATE=200;ACTTIMEDEFOFFVALFORUNCELLH=100ACTTIMEDEFOFFVALFORUNCELLNOH=100OAMGUARDVALFORLOWRATE=200OAMGUARDVALFORMIDRATE=200OAMGUARDVALFORHIGHRATE=200ACTTIMEDEFOFFVALFORSAMECELL=802.2检查跨RNC小区的切换参数参数编号英文名称中文名称推荐值说明1HYSTFOR1G1G迟滞7ADD CELLINTRAFREQHO2TRIGTIME1G1G事件触发时间D1280ADD CELLINTRAFREQHO3PERIODFOR1G1G事件重试周期4ADD CELLINTRAFREQHO4AMNTOFRPT1G1G事件重试最大次数0ADD CELLINTRAFREQHO5FILTERCOEFFOR1G1I同频测量层三滤波系数D5ADD CELLINTRAFREQHO6HYSTFOR2A2A迟滞15ADD CELLINTERFREQHONCOV7TRIGTIME2A2A事件触发时间D1280ADD CELLINTERFREQHONCOV8PERIODFOR2A2A事件重试周期4ADD CELLINTERFREQHONCOV9AMNTOFRPT2A2A事件重试最大次数0ADD CELLINTERFREQHONCOV10FILTERCOEFFOR2A2A测量的滤波系数D5ADD CELLINTERFREQHONCOV11INTERCELLANTIPINGPANGTIMERLTH防止非覆盖小区间乒乓切换定时器0ADD CELLHOCOMM12BATON_HHO_SUPP接力切换总开关ONSET CORRMALGOSWITCH13BATONHOSUPPROT邻区接力切换开关ALL_SUPPMOD NCELL14HONULLACTTIMESWITCH切换时立即激活开关不涉及H业务ON（对于非跨RNC小区，且没有打开帧分时，选择“ON”；对于跨RNC小区或打开帧分的小区，选择“OFF”）MOD CELLRLACTTIME15ADAPTIVEALGOSWITCH接入激活时间智能计算开关OFFMOD CELLRLACTTIME16MIDRATERLACTTIMEDEFOFFVAL中速链路激活时间缺省偏移值60MOD CELLRLACTTIME17HIGHRATERLACTTIMEDEFOFFVAL高速链路激活时间缺省偏移值60MOD CELLRLACTTIME18ACTTIMEDEFOFFVALFORUNCELLH切换情况下涉及H业务的激活时间偏移值100MOD CELLRLACTTIME19HONULLACTTIMER