光纤收发器NT-1100.doc

Contents1. Product :NMS-Type media converter 2 Model: NT-102M Series22. Product: Intelligent Fast Ethernet Media Converter7 Model: NT-1100 Series73. Product:10/100/1000M Media Converter12 Model: NT-3012 Series124. Product: Gigabit Ethernet Media Converter15 Model: NT-2100 Series155. Product: NT-16 Media Converter Rack18 Model: NT-16186. Product: NT-14 Media Converter Rack20 Model: NT-14207. Product: NT-1020 10/100M mode Converter22 Model: NT-1020 Series228. Product: NT-2020 GIGA mode Converter25 Model: NT-2020 Series259. Product: 10/100M media converter with 2-TX ports27 Model: NT-1200 Series27 NT-4500PD30 PD (Powered Device) 10/100Base-TX-to-100Base-FX Media Converter30 NT-4500PSE32 PSE (Power Source Equipment) 10/100Base-TX-to-100Base-FX Media Converter3210 Product: RS232/422/485 Fiber Optic Modem34 Model: NT-277 Series3411. Product: PDH Series Optical Multiplexers36 Model: PDH Series3612. Product: E1-10/100BASE-T Bridge39 Model: NE-2701, NE-27023913. Product: V.35 Protocol Converter42 Model: NE-2703, NT-27044213. Product: V.35 Fiber Optic Modem45 Model: NE-27074513. Product: 4E1-10/100Base-T Bridge48 Model: NE-27084813 Product: E1 Fiber Optic Modem50 Model: NE-270650491. Product: NMS-Type Media ConverterModel: NT-102M SeriesProduct OverviewNT-102M, a 10/100M adaptive fast Ethernet media converter with network management system, supports Web interface management, remote Telnet management & software upgrade, and serial port management & software upgrade, which can monitor working status and configure the modes of the local and the remote device.The 10/100M media converter completely complies with such international standards as 10Base-T, 100Base-TX, 100Base-FX and IEEE 802.3x, and is fully compatible with network interface cards, relays, hubs and switches of other manufacturers. It provides a low-cost and high-reliability hardware solution for information transmission in broadband private networks and fiber broadband metropolitan area networks. Function & Features Graphic management interface based on WEB address and SNMP protocol; Supporting LFP (Link Fault Pass Through) of the local and remote; The network interfaces of the NMS proxy module and NMS media converter module support the auto-sense of MDI-MDIX Compliance with IEEE 802.3u 100BASE-FX/TX and IEEE802.3 10BASE-T; Supporting IEEE 802.1Q VLAN; Supporting 10/100M auto sensed, full/half-duplex auto sensed; Supporting the transmission of packets of 1600 bytes at the maximum; Supporting Quality of Service (QoS), and he transmission of VoIP packets; Supporting Spanning Tree Protocol (STP) to form a redundant network; Supporting hot swapping in the rack; Card type can be plug into both desktop box and the rack; Extremely low power consumption, low heat, reliable and stable performance, and long lifetime; Options in multimode dual fiber, single mode and single mode single fiber Options in different types of optical interfaces, such as SC, ST, etc.Technical ParametersAccess mode10/100MbpsOperating temperature-10C +55CStorage temperature-40C +70CPower selectionAC220V/AC110V / DC-48VPower consumption2WDimensions140 mm (W) * 110 mm (D) * 40 mm (H) (internal power supply)71mm (W) * 94mm (D) * 26 mm (H) (external power supply)25 mm (W) * 152 mm (D) * 128 mm (H) (module type)Optical FeaturesMulti-modeApplicable fibers: 50/125, 62.5/125, 100/140mMulti-mode 2km or multi-mode 5kmTransmitting power: -20 -14 dBReceiving sensitivity: -31 dBmTransmission distance: 0 2km or 05kmOptical connector: SC (standard)/FC (optional)/ST (optional)Optical port: dual fiberWavelength: 850nm/1310nmSingle modeApplicable fibers: 9/125, 8.3/125, 8.7/125m or 10/125mSingle mode 20kmTransmission distance: 020kmTransmitting power: -15-8 dBm (dual fiber), -14-8 dBm (single fiber)Receiving sensitivity: -34 dBm (dual fiber), -33 dBm (single fiber)Optical connector: SC (standard)/FC (optional)/ST (optional)Optical port: single fiber/dual fiberWavelength: 1310nm/1550nm (single fiber); 1310 nm (dual fiber)Single mode 40kmTransmission distance: 040kmTransmitting power: -10-5 dBm (dual fiber), -9-5 dBm (single fiber)Receiving sensitivity: -36 dBm (dual fiber), -50 dBm (dual fiber), -60 dBm (single fiber)Receiving sensitivity: -8-2 dBm (dual fiber), -33 dBm (single fiber)Receiving sensitivity:-6-1 dBm (dual fiber), -40 dBm (single fiber)Receiving sensitivity: -50 dBm (dual fiber), -31 dBm (single fiber)Receiving sensitivity: -38 dBmOptical connector: SC (standard)/FC (optional)Optical port: dual fiberWavelength: 1550 nmTypical Application of Media Converter in overall NetworkConnection in centralized management modeConnection in point-to-point modeOrder InformationMedia Converter Series with Network Management ModelSpecificationsDual fiber, SeriesNT-102MMNetwork management board, SNMP, RJ45/RS232NT-102MPSupporting network management, 10/100M, multi-mode, 2 km, SC/ST, module typeNT-102MSupporting network management, 10/100M, multi-mode, 2 km, SC/ST, aluminum alloy, stand aloneNT-102MPSupporting network management, 10/100M, single mode, 20/40/60/100 km, SC, module typeNT-102MSupporting network management, 10/100M, single mode, 20/40/60/100 km, SC, aluminum alloy, stand aloneSingle mode single fiber SeriesNT-S102MP-20Supporting network management, 10/100M, single mode, single fiber, bi-directional, 20/40/60/80 km, SC, module typeNT-S102M-20Supporting network management, 10/100M, single mode, single fiber, bi-directional, 20/40/60/80 km, SC, aluminum alloy, stand alone2. Product: Fast Ethernet Media ConverterModel: NT-1100 SeriesIntelligent Fast Ethernet Media Converter SeriesOverviewDue to its unique function of link failure alert between electrical port and optical one, the intelligent 10/100M adaptive fast Ethernet media converter can replace the media converter with network management to greatly reduce the system cost. NT-1100 Ethernet media converter can interconvert electrical signals of 10Base-T and 100BaseTX twisted pairs with optical signals of 100Base-FX. It extends the network transmission distance from 100m via copper cables to 120 km via fiber optical cable. It enables the data to transmit in two different mediums of electrical and optical networks either by the technology of data link L2 store-and-forward, or by the one of PHY L1 cut-through). It supports transmission in multi-mode dual fiber, single mode dual fiber and single mode single fiber. Features 10/100Mbps auto-sensed, facilitating network upgrade Built-in efficient switching core to implement flow control and reduce broadcast packets full-duplex and half-duplex auto-sensed Supporting automatic cross connection of twisted pair interfaces, facilitating system commissioning and installation Supporting Link Failure Alert (LFA) Supporting half /full-duplex of FX and link failure alert with optional dip-switch Supporting 10/100Mbps store-and-forward and 100Mbps cut-through transmission with optional dip-switch(unique) Supporting low-timelag transmission Supporting the transmission of extra-long packets up to1600 bytes Supporting the transmission of extra-long VLAN packets Supporting Quality of Service (QoS) , ensuring the transmission of VoIP packets Supporting STP to form a redundant network Extremely low power consumption (less than 2W), low heat, reliable and stable performance, and long lifetime; Options in single mode dual fiber, multi-mode dual f fiber, and single mode in single fiberApplication10/100Mbps fast optical Ethernet long-distance transmitting networkTechnical IndexesParameterSpecificationsAccess mode10/100MbpsStandardIEEE802.3 10Base-T Ethernet, IEEE802.3u,100Base-TX/FX Fast Ethernet, IEEE802.3x Flow control,IEEE802.1q VLAN,IEEE802.1p QoS,IEEE802.1d Spanning TreeWavelength850nm/1310nm/1550nmTransmission distanceDual-fiber multi-mode: 2 km; Dual-fiber single mode: 20/40/60/80/100/120 km; Single fiber single mode: 20/40/60/80/100 kmCategory-5 twisted pairs: 100mPortOne RJ45 port: For connecting STP/UTP category-5 twisted pairsOne optical port: Multi-mode, dual fiber: SC or ST (50, 62.5/125m)Single mode, dual fiber: SC or FC (9/125m)Single mode Single fiber: SC or FC (9/125m)Conversion meansMedia conversion, store-and-forward/cut-throughMAC address table1KBuffer space1MbitFlow controlFull duplex: flow control; Half duplex: back pressureDelayStore-and-forward: 9.6s; cut-through: 0.9sBER19-9MTBF100,000 hoursLED indicatorPOER (power supply); FX LINK/ACT (optical link/action)FDX (FX full duplex), TP LINK/ACT (twisted pairs link/action)TP 100 (100M transmission rate of twisted pairs), FX 100 (100M transmission rate of optical fiber)Power supplyDC5V 1A (external), AC220 0.5A/DC-48 (internal)Power consumption2WOperating temperature-1055C Operating humidity5%90% Maintaining temperature-4070CMaintaining humidity5% 90% non-condensingDimensions140 mm (W) * 110 mm (D) * 40 mm (H) (internal power supply)71mm (W) * 94mm (D) * 26 mm (H) (external power supply)25 mm (W) * 152 mm (D) * 128 mm (H) (card type)Order InformationModelSpecificationsDual fiber Bi-directional seriesNT-110010/100M, multi-mode, 2 km, SC/ST, stand aloneNT-102F10/100M, multi-mode, 2 km, SC/ST, module type (applicable to NT-R16 rack)NT-1100P10/100M, multi-mode, 2 km, SC/ST, module type, 113C (applicable to NT-R16M rack)NT-1100D10/100M, multi-mode, 2 km, SC/ST, aluminum alloy, stand alone, 113CNT-1100S10/100M, single mode, 20/40/60/100 km, SC, stand aloneNT-102F10/100M, single mode, 20/40/60/100 km, SC, module type (applicable to NT-R16 rack)NT-1100P10/100M, single mode, 20/40/60/100 km, SC, module type, 113C (applicable to NT-R16M rack)NT-1100D10/100M, single mode, 20/40/60/100 km, SC, aluminum alloy, stand alone, 113CSingle fiber Bi-directional seriesNT-S110010/100M, single mode, single fiber, bi-directional, 20/40/60/80 km, SC, stand aloneNT-S102F10/100M, single mode, single fiber, bi-directional, 20/40/60/80 km, SC, module type (applicable to NT-R16 rack)NT-S1100P10/100M, single mode, single fiber, bi-directional, 20/40/60/80 km, SC, module type, 113CNT-S1100D10/100M, single mode, single fiber, bi-directional, 20/40/60/80 km, SC, aluminum alloy, stand alone, 113C3. Product: 10/100/1000M Media ConverterModel: NT-3012 Series10/100/1000M Self-sensed Gigabit Ethernet Media Converter SeriesOverviewNT-3012 10/100/1000Mbps adaptive Gigabit Ethernet media converter adopts switching technology to fulfill media conversion. It complies with IEEE802.3, IEEE802.3u, IEEE802.3z and IEEE802.3ab standards. Presently it supports two types of media network connections: 10Base-T/100Base-TX/1000Base-T, and 1000Base-SX/LX, inter-converting electrical signals of 10Base-T/100Base-TX/1000Base-T twisted pairs with optical signals of 1000Base-SX/LX. It extends the transmission distance of network from 100m via copper cable to 20 km via fiber optical cables. It supports transmission in multi-mode dual fiber, single mode dual fiber and single mode single fiber.Features Completely compatible with products of CISCO, HUAWEI and 3COM. The product adopts a low-power-consumption chip; the heat output is so low that no heat dissipation facility is needed. Supporting inter-conversion between adaptive 10Base-T/100Base-TX/1000Base-T and 1000Base-SX/LX Supporting full-duplex and half-duplex and its auto-sensed Supporting automatic cross connection of twisted pair interfaces, facilitating system commissioning and installation Supporting the transmission of extra-long VLAN packets Supporting Quality of Service (QoS) and ensuring the transmission of VoIP packets; Supporting STP to form a redundant network; Options in single mode dual fiber, multi-mode dual fiber, and single mode in single fiberApplication10/100/1000Mbps Gigabit optical Ethernet long-distance transmitting networkTechnical Indexes ParameterSpecificationsAccess mode10/100/1000Mbps Gigabit EthernetStandardIEEE802.3 10Base-T Ethernet, IEEE802.3u 100Base-TX/FX Fast Ethernet, IEEE802.3ab 1000Base-T , IEEE802.3z 1000Base-SX/LX Gigabit thernet,IEEE802.1qVLAN,IEEE802.1p QoS,IEEE802.1d Spanning TreeWavelength850nm/1310nm/1550nmTransmission distancemulti-mode Dual-fiber: 220m (62.5/125m)/550m (50/125m)single mode Dual-fiber: 20/40/60/80 Kmsingle mode Single fiber: 20/40/60/80 KmCategory-5 twisted pairs: 100mPortOne RJ45 port: Connecting with STP/UTP category-5 twisted pairsOne optical port: Multi-mode Dual-fiber: SC (50, 62.5/125m)Single mode Dual-fiber: SC/FC (9/125m)Single mode Single fiber: SC/FC (9/125m)Conversion meansMedia conversionDelay10usBER10-9MTBF100,000 hoursLED indicatorPOWER (power supply), FX LINK (optical link action), TP LINK1000 (twisted pair connection to 1000M), TP LINK100 (twisted pair link to 100M), TP ACT (twisted pair packet forwarding action)Power supplyAC220 0.5A/DC-48 (built-in)Power consumption5WOperating temperature-1055COperating humidity5%90% Maintaining temperature-4070CMaintaining humidity5% 90% non-condensingDimensions65mm(H)*162mm(W)*152mm(D) (internal power supply)110mm(H)*22mm(W)*81mm(D) (card type)Order Information10/100/1000M Adaptive Media Converter SeriesModelOptical link ModeNT-3012BMTP SC MMSC, multi-mode, 850nm, 10/100/1000M single-layer upgrade versionNT-3012BSTP SC SMSC, single mode, 1310nm, 10/100/1000M single-layer upgrade versionNT-3012BVTP VF-45 MMVF-45, multi-mode, 850nm, 10/100/1000M single-layer upgrade versionNT-3012BTTP MT-RJ MMMT-RJ, multi-mode, 850nm, 10/100/1000M single-layer upgrade versionNT-3012BTSTP MT-RJ SMMT-RJ, single mode, 1310nm, 10/100/1000M single-layer upgrade versionNT-3012PModule type4. Product: Gigabit Ethernet Media ConverterModel: NT-2100 SeriesGigabit Ethernet Media Converter SeriesOverviewNT-2100 1000Mbps Gigabit Ethernet media converter adopts switching technology to fulfill media conversion. It complies with IEEE802.3z and IEEE802.3ab standards, and supports two types of media network connections: 1000Base-T and 1000Base-SX/LX. It inter-converts electrical signals of 1000Base-T twisted pairs with optical signals of 1000Base-SX/LX, extending the transmission distance of a network from 100m via copper cables to 50 km via fiber optical cables. It supports transmission in multi-mode dual fiber, single mode dual fiber and single mode single fiber.Features Supporting inter-conversion between 1000Base-T and 1000Base-SX/LX Supporting full-duplex and half-duplex and its auto-sensed Supporting automatic cross connection of twisted pair interfaces, facilitating system commissioning and installation Supporting the transmission of extra-long VLAN packets Supporting Quality of Service (QoS) and ensuring the transmission of VoIP packets; Supporting STP to form a redundant network; Options in single mode dual fiber, multi-mode dual fiber, and single mode in single fiberApplication1000Mbps Gigabit optical Ethernet long-distance transmitting networkTechnical Indexes ParameterSpecificationsAccess mode1000Mbps Gigabit EthernetStandard IEEE802.3ab 1000Base-T , IEEE802.3z 1000Base-SX/LX Gigabit thernet,IEEE802.1qVLAN,IEEE802.1p QoS,IEEE802.1d Spanning TreeWavelength850nm/1310nm/1550nmTransmission distanceDual-fiber multi-mode: 500m (fiber size: 62.5/125m)/550m (fiber size: 50/125m)Dual-fiber single mode: 20/40/50/80KmSingle fiber single mode: 20/40/60KmCategory-5 twisted pairs: 100mPortOne RJ45 port: Connecting with STP/UTP category-5 twisted pairsOne optical port: Multi-mode Dual-fiber: SC (50, 62.5/125m)Single mode Dual-fiber: SC/FC (9/125m)Single mode Single fiber: SC/FC (9/125m)Conversion meansMedia conversionDelay10usBER10-9MTBF100,000 hoursLED indicatorPOWER (power supply), FX LINK (optical link action), TP LINK1000 (twisted pair link1000M), TP LINK100 (twisted pair link 100M), TP ACT (twisted pair packet forwarding)PowerAC220 0.5A/DC-48 (built-in)Power consumption5WOperating temperature-1055C Operating humidity5%90% Maintaining temperature-4070CMaintaining humidity5% 90% non-condensingDimensions65mm(H)*162mm(W)*152mm(D) (internal power supply)110mm(H)*22mm(W)*81mm(D) (card type)Order Inform