DLS01门灯开关产品规格书.doc

ISO14001: 2004ISO9001: 2000 APPROVAL SPECIFICATIONS Title. Door lamp switch Part NO. DLS01系列 Customers Part NO. Model: Customers Approval Requested. Please return this copy as a certification of your approval.Checked by: Date: Approved by: Date: APPROVEREVIEWPOLT孙自波林小军金成尧WENZHOU GANGYUAN ELECTRONICS CO.，LTD. GANGYUAN APPROVAL SPECIFICATIONS CUSTOMERCUSTOMERS P/NGYES P/NPRODUCTREVISIONDLS01系列Door lamp switchA1、温度范围 Temperature range1.1使用温度范围：-25 85 Temperature range for use：-2585 2、测试环境条件： Test circumstance condition： 环境温度：2510 Ambient temperature ： 2510 相对湿度：45%85% Relative humidity ： 45%85% 空气压力：102千帕 Air pressure：102KPa3、外观、结构和尺寸 Appearance 、structure and dimension 3.1外观: Appearance: 外观美观、标志清晰、没有生锈、伤痕、电镀不良、破裂，剥离现象。动作正常，换位清晰。 Nice appearance，clear mark，free from rust，scar，bad platting， denude，normal action，clear conversion。 3.2结构和尺寸： Structure and Dimension: 参照有关外形图 Reference to the relative4、额定值：CQC： 6A 250V AC Rating： CQC：6A 250V AC APPROVE BY孙自波11.10.13CHECKED BY林小军11.10.13PRPARE BY金成尧11.10.13Page 1 of 5 GANGYUAN APPROVAL SPECIFICATIONS CUSTOMERCUSTOMERS P/NGYES P/NPRODUCTREVISIONDLS01系列Door lamp switchA项 目ITEM试 验 条 件TEST CONDITIONS要求REQUIREMENTS5、机械性能Mechanical Performance5.1动作力Operating Force开关垂直于操作方向放置，在按钮一侧逐渐施力，测量开关导通所需的最大力度。Vertical placing the switch with the direction of switch operation, then gradually increasing the force, measure demanded maximum force that switch continuity. 2.00.8N5.2端子强度Terminal strength 在端子的顶部施加一向外拉或向内推的50N静负荷，持续10秒。Enforce pull-outward or push-inward static 50N load on the top of terminal, lasting 10 seconds端子无损伤，脱落，开关功能动作正常。No damage, leafing, switch function action is normal.5.3可焊性试验Solder-Ability将端子浸入熔融的锡槽内，温度为2355，时间为30.5秒。Immerse the terminal to the molten solder tank, temperature reach to 2355,time reach to 30.5 seconds浸入的部分90%以上表面被锡覆盖。90% of the surface will be covered by solder.5.4耐焊性试验Soldering resistance test端子的焊接部分浸入温度为2605熔融的锡炉内30.5秒。The welding part of terminal immerse molten solder at a temperature of 2605 for 30.5 seconds.本体无变形，能满足于机械、电气性能Without deformation of base, can satisfy mechanical, electronic performance.手工烙铁焊接：焊接温度3505，焊接时间30.5秒。焊接时在端子上不能施加异常压力。Manual iron welding: welding temperature: 3505,welding time: 30.5 seconds. When welding, cant enforce anomaly pressure on the terminal.APPROVE BY孙自波11.10.13CHECKED BY林小军11.10.13PRPARE BY金成尧11.10.13Page 2 of 5 GANGYUAN APPROVAL SPECIFICATIONS CUSTOMERCUSTOMERS P/NGYES P/NPRODUCTREVISIONDLS01系列Door lamp switchA项目ITEM试 验 条 件TEST CONDITIONS要求REQUIREMENTS5.5振动试验Vibration test振幅25mm，加速度520g，垂直振动，正弦波。Amplitude: 25mm, acceleration: 520g, vertical vibration, sine wave.外观无明显异常，功能动作正常。Appearance is no obvious anomaly function action should be normal.6、电气性能Electronic Performance6.1接触电阻Contact resistance在1KHz小电流下测量。Being measured at 1KHz small current.50毫欧姆以下50m MAX.6.2绝缘电阻Insulation resistance在端子之间和端子与外壳之间施加DC500V，一分钟后测量。Measurement shall be made enforcing DC500V between terminals and between terminals and frame for 1 minute. 100兆欧姆以上100M MIN.6.3耐电压Withstand voltage在极与极之间施加AC1000V，0.5mA 1分钟，在极与外壳之间施加AC3750V，0.5mA 1分钟。Enforce AC1000V, 0.5mA between pole and pole in 1 minute ,enforce AC3750V，0.5mA between pole and frame in 1 minute.无击穿现象出现。No breakdown.7、耐久性能Durability7.1机械寿命Mechanical life 每分钟30次的速度连续工作3E4次Operating 1E4 cycles at a rate of 40cycles per minute外观，动作功能正常7.2电气寿命Electrical Life 额定负载条件下,每分钟8次的速度操作1E4次.Operating 1E4 cycles at a rate of 8 cycles per minute under rate loading.1.温升30K Temperature raising 30K2.耐电压1500V/1minWithstand voltage10000V/1minAPPROVE BY孙自波11.10.13CHECKED BY林小军11.10.13PRPARE BY金成尧11.10.13Page 3 of 5 GANGYUAN APPROVAL SPECIFICATIONS CUSTOMERCUSTOMERS P/NGYES P/NPRODUCTREVISIONDLS01系列Door lamp switchA项目ITEM试 验 条 件TEST CONDITIONS要求REQUIREMENTS8、耐候性Weather Ability8.1耐高温试验Heat test在852环境中放置96小时，再放在正常环境中30分钟后进行测试。Putting at 852 for 96 hours. Test after keeping in normal condition for 30 minutes.1、接触电阻50毫欧以下Contact resistance50m MAX. 2、绝缘电阻100兆欧以上Insulation resistance100M MIN.3、耐电压 1500V, 0.5mA 1分钟无击穿Withstand voltage 1500V,0.5mA,no breakdown.4、无任何迹象显示机械及电气性能之损坏No sign of damage mechanical and electronic performance.8.2耐湿试验Anti-humid test在温度为402，相对湿度为91%-95%RH的环境中放置96小时，再放在正常环境中30分钟后进行测试。Putting at 402, 91%95%RH for 96 hours. Test after keeping in normal condition for 30 minutes.8.3耐低温试验Anti-low temperature test在-253的环境中放置96小时，再放在正常环境中30分钟后进行测试。Putting at -253 for 96 hours. Test after keeping in normal condition for 30 minutes.8.4温度交变试验Temperature cycling test在如图示之环境中，循环5次后，再置于正常环境中，30分钟后进行测试。In FIG. For 5 cycles, test after kept in normal condition for 30 minutes. +85 -25 One cycle 2 1 2 1 Hours APPROVE BY孙自波11.10.13CHECKED BY林小军11.10.13PRPARE BY金成尧11.10.13Page 4 of 5 GANGYUAN APPROVAL SPECIFICATIONS CUSTOMERCUSTOMERS P/NGYES P/NPRODUCTREVISIONDLS01系列Door lamp switchA General tolerance：0.1mmNO.NAMEMATERIALNATIONALITYQTY.FI