rt5370驱动移植.doc

RT5370 驱动移植硬件：ARM 开发板 OK6410系统：linux 2.6.28内核无线USB网卡 腾达 型号：W311M芯片类型rt5370第一步：下载驱动驱动下载地址腾达官网下载/tendacn/ . ctid=172&type=2 或者到无线芯片组解决方案开发商 Ralink Technology公司官网下载/en/04_support/support.php?sn=501 第二步：解压 tar jvxf2011_0225_RT5370_RT5372_Linux_STA_V_DPO.tar.bz2修改驱动源码根目录下的MakefilePLATFORM=SMDKLINUX_SRC=/usr/local/arm/linux-2.6.28(内核源码目录)CROSS_COMPILE=/usr/local/arm/4.2.2-eabi/usr/bin/arm-linux- 第三步：编译驱动#make在os/linux 目录生成最后的ko文件rt5370sta.ko第四步：将rt5370驱动源码目录下的RT2870STA.dat拷贝到/etc/Wireless/RT2870STA/目录下（首先要创建/etc/Wireless/RT2870STA）第五步：加载驱动将rt5370sta.ko拷贝到开发板#insmod rt5370sta.korootOK6410 linux# insmod rt5370sta.kortusb init rt2870 -= pAd = c884c000, size = 512016 =- RTMPAllocTxRxRingMemory, Status=0RTUSBVenderReset Error! The chip does not support 5G band 15!RTMPSetPhyMode: channel is out of range, use first channel=1(Efuse for 3062/3562/3572) Size=0x2d 2d0-2fc3. Phy Mode = 9MacValue1=2MacValue2=0MCS Set = ff 00 00 00 01 rt2x00_set_chip: Info - Chipset detected - rt: 5390, rf: 5370, rev: 0502.接着，将驱动源码目录下common/rt2870.bin文件拷贝到开发板/lib/firmware/目录下激活无线接口rootFORLINX6410# ifconfig wlan0 upphy1 - rt2x00lib_request_firmware: Info - Loading firmware file rt2870.bin.phy1 - rt2x00lib_request_firmware: Info - Firmware detected - version: 0.236.phy1 - rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102.phy1 - rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188.phy1 - rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.phy1 - rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.rootFORLINX6410# phy1 - rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0.phy1 - rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.phy1 - rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94.phy1 - rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47.然后配置无线网络ESSID ,配置自动获取IP后，就可以上网了。原帖地址/lanyang123456/article/details/7370805 参考：将 RT73 无线网卡驱动移植到 ARM