模具词汇.doc

一、模具词汇：1.模具：mold; mould; tool2.模胚：mold base3.塑胶，胶位：plastic4.模具图纸：mold drawing5.模胚/模架：mold base; mold frame6.模板：mold plate7.模具类型：mold type(两板模：2-plate mold, 三板模：3-plate mold)8.前模（母模）：cavity, fixing side(固定侧)；cavity也有型腔的意思，缩写为cav.9.后模：core; moving side(移动侧)10.镶件（入子）：insert; 可换镶件：interchangeable insert 前（后）模镶件：cavity(core) insert11.进胶点，浇口：injection point,; gate 入水形式：gate type 潜水：sub-gate;tunnel-gate 直入水（大水口）：direct gate 边入水：edge gate 点入水：pin point gate 扇形入水：fan gate 香蕉形入水：banana gate 腰果形入水：cashew gate 月亮形入水：moon gate1.面板：top clamp plate2.底板：bottom clamp plate3.水口板：runner stripper plate4.推板：stripper plate5.托板：support plate6.方铁(也有公司叫模脚)：spacer block7.顶针面板：ejector retainer plate8.顶针底板：ejector plate9.导柱：leader pin10.导套：leader bush1.中托司：ejector guide pin2.中托司套：ejector guide bush3.排气：vent4.回针：return pin5.斜边，斜导柱：angular pin6.撑头：support pillar7.定位圈：locating ring8.销钉：dowel pin9.隔水片：baffle10.唧嘴：sprue bushing1.变形：deformdeformeddeformationwarpwarpedwarpagedistortdistorteddistortion2.缩水：shrink缩水率：shrinkage rate缩水纹：sink mark3.顶白：ejection mark4.流痕：flow mark5.粘模：sticking6.拖花：scratch7.批锋：flash8.烧焦痕：burn mark9.困气：gas trap10.走胶不满：short shot; not filled11.流道类型：runner type冷流道：cold runner热流道：hot runner一、句子表达：1.这个产品有点变形This part is a little deformed.2.产品骨位太厚，表面容易产生缩水This rib is too thick, easy to have(cause/appear) sink mark.3.成形后，产品表面有困气，建议增加镶件。After molding, there is gas trap on the part surface,suggest adding insert.4.产品表面会有缩水纹There will be sink mark on part surface.5.产品粘后模The part is sticking on the core.1.现在图纸上为前后模原身出，我们希望做镶件，可以吗？On the drawing,the cavity and core is directly cut into plate(mold base),we want to make insert,OK？2.请确认产品排位是否OK。Please confirm the layout of the part is OK or not.3.为方便加工（为增加骨位排气），建议此处做镶件。For easy machining,(For adding vent at rib),we suggest making insert here.为了做某事、-In order to do、1.为了满足啤机(注塑机)的吨位，将面板宽度修改为35mm,可以吗？ In order to meet the injection machine ton,we want to change the width of the top clamp plate to 35mm,OK？2.导柱需加油槽及拆卸牙。 Grease slot and the screw must be added to the leader pin.3.顶针与运水距离较近，可以将顶针改小吗？ EJ pin is too close to the cooling, could we change a smaller EJ pin?1.你好，很高兴见到你。 Hello.Nice to meet you.2.我是工程师（设计师），我叫、 I am an engineer(designer),my name is-3.我们可以改做三板模吗？ Could we change it to 3 plate mold?4.在此处做潜水，可以吗？ Could we mak