实施方案---NCS6100DFS200065108510

中国人民银行征信中心2016年度存储设备DCN实施方案1、NCS6100高端存储的实施31.1、NCS6100技术实施要点31.2、NCS6100配置步骤概述31.3、NCS6100划盘详细实施步骤41.4、NCS6100 Volume主机映射详细步骤122、海量存储实施方案222.1、存储配置和环境信息222.2、存储硬件安装和加电232.3、集群存储初始化292.4、集群存储基本功能模块配置412.5、集群存储高级功能模块配置603、光纤导向器实施方案634、光纤交换机实施方案641、NCS6100高端存储的实施1.1、NCS6100技术实施要点NCS6100实施步骤：1、硬件到货后在机房内静置24小时。2、硬件联线、加电测试、升级微码。3、Bin file讨论、确认，bin file CCA流程。4、Load bin file，根据需求划分硬盘空间。5、把所划分硬盘空间提供给主机使用。1.2、NCS6100配置步骤概述划盘配置步骤：第一步：创建Thin Device第二步：创建Thin Meta Device第三步：将Thin Meta Device绑定到Pool里Volume主机映射步骤：第一步：创建Storage Group第二步：创建Initator Group第三步：创建Port Group第四步：创建Masking View1.3、NCS6100划盘详细实施步骤创建Thin Device（非meta设备）登录Unisphere后，进入StorageVolume点击”Create Volume”进入界面后，填写相关信息，点击”Run Now”Configuration：选择TDEV，代表Thin Device。NCS6100所有映射给主机的Lun均为Thin DeviceEmulation：选择默认FBANumber Of Volumes：需要创建Thin Device的数量Volume Capacity：每个Thin Device的大小Bind to pool：选择Thin Device需要绑定的Pool。此处可以不选择Pool，待Lun创建完成后，再手工绑定PoolPreallocated Capacity for each Volumes：预分配空间选项a) Full volume：按照volume大小全部分配b) By Capacity：制定预分配大小c) 选择Persist preallocated capacity through reclaim or copy表示对该Thin Device在使用过程中不做空间回收创建Thin Meta Device1. 进入StorageVolume2. 点击”Create a meta volume”3. 进入界面，选择Meta Volume的配置方式，点击”Next”Emulation：选择默认FBAHow would you like to create meta：选择以新建方式创建Meta Volume，或使用原有Thin Device创建Meta Volume。注：如用原有的Thin Device创建Meta Device，需要之前建的Thin Device不能Bind到Pool里Meta Volume Configuration：选择配置方式，条带划或者拼接方式4. 填写Meta Volume的数量及大小设置注：截图以2个Meta8的Volume为例，Meta 8代表用8个Thin Device组成一个Meta Volume。5. 检查相关配置，点击”Run Now”，完成创建。注：当创建完Meta Device后，Meta Device并不能使用，需要手工将Meta Device绑定到Pool后才能使用绑定Thin Meta Device到Pool里注意：请只将新创建的thin device，绑定到FC的pool里，不要绑定到EFD pool。 存储配置了自动分层功能，会自动根据数据访问频率，将性能需求高的数据块，挪到EFD上，这样可以提高闪存盘的使用效率。1. 进入StorageVolume2. 选择”TDEV”，点击”View”3. 进入界面后，选择需要Bind的Volume，点击Bind注：可以看到”Allocated%”为0%，并且”Status”状态为Not Ready的Lun，这些Volume均为没有Bind到Pool里的Volume。（两个条件必须同事满足）4. 选需要绑定的Pool名称，并且选择预分配空间选项（同创建Thin Device），点击”OK”，volume绑定到Pool成功。1.4、NCS6100 Volume主机映射详细步骤创建Storage Group1. 进入Storage Storage Group2. 点击”Create”3. 建立一个空的Storage Group4. 选择上步建立的空的Storage Group，点击View Details5. 点击右上角”Volume”6. 点击”Add”，添加Volume7. 选择需要添加到SG里的Volume，点击”OK”，Storage Group创建完成。创建Initator Group8. 进入Host Initiators9. 查看主机HBA卡WWN信息是否已经Log in。注：如果没有Log In为No或者列表里没有相应的WWN，说明主机到存储之间的zone不通10. 进入Host Initiator Group,11. 点击”Create”，创建Initiator Group12. 进入界面后，填写主机名称，选择主机HBA卡的WWN，点击”Add”添加，主机的所有WWN添加完成后，点击”Finish”。创建完成注：命名规则建议为主机名_IG，例如：IC01_IG创建Port Group1. 进入Host Port Group2. 点击”Create”3. 填写Port Group名称，选择相应存储前端口并点击”Add”添加，添加完成后，点击”OK”，Port Group创建完成创建Masking View1. 进入Host Masking View2. 点击”Create”3. 填写Masking View名称，选择相应的Storage Group、Port Group、Initiator Group，点击”OK”，Masking View创建完成4. 主机扫描磁盘，认盘完成给已使用主机增加认盘执行下面三步，并做好相应的记录： 按照2.2.2创建thin meta device 按照2.3绑定thin meta到pool 按照2.4.1将thin meta加入相应的storage group2、海量存储实施方案2.1、存储配置和环境信息项目采购的存储配置集群存储包括7台DFS2210和2台8口MELLANOX交换机。单个DFS2210配置为144TB HDD、24G RAM、2个万兆端口、2个千兆端口。整个集群空间1008TB。机房环境准备以下为本次采购设备物理规格要求，需要在安装前准备：室内温度室内温度变化范围: (10C35C)，室内湿度范围：5-95%设备硬件尺寸和重量.本章节详细介绍本次采购的设备物理尺寸如下：硬件型号Dimensions公制堆叠高度数量DFS2210 高17.7厘米4U7宽48厘米深79.4厘米重54公斤注意：为了保证系统可以正常拆卸或安装硬件时进行维护，请确保机器前面空88.9CM，机器后面空出35.6CM。DFS DFS2210设备供电要求DFS2210配置2路电源，每路电源额定电压240、电流3A，功率720W。电源线规格为IEC320 C14-C13,208V UNIVERSAL。硬件型号电压电流功率冗余功率DFS22102403A720W1250WDFS机柜的电源要求本项目共7个DFS2210节点，每个DFS2210占用4U空间.考虑到电源冗余，建议节点每路电流配置4A以上，机柜可以选用每路32A的PDU，每个机柜2路，共64A。硬件型号容纳DFS2210个数单路电流机柜732ADFS2210设备散热要求硬件型号散热量（BTU/hr）最大值DFS221025002.2、存储硬件安装和加电硬件安装步骤拆箱拆箱并确认所有系统部件,安装附件和软件包均包装完整,数量与订单一致。上架第一个机柜上架前6个DFS2210节点，第二个机柜上架后6个DFS2210节点。 前面板和铰链安装安装左，右铰链支架到机器上将前面板和左右铰链支架用螺丝固定连接显示线缆和前面板的PC板安装硬盘滑轨的安装抽出滑轨最内侧的轨道将内侧滑轨安装到DFS IQ节点上将导轨固定在机柜上安装DFS IQ节点到滑轨上给DFS IQ节点加电内部连线DFS DFS2210内部节点采用Infiniband高速网络互连，每个DFS2210节点配置两个IB端口，两个端口分别连接到两个不同的IB交换机。外部连线DFS2210外部网络连接包含千兆管理网络和万兆数据网络。每个DFS2210的2个千兆网口连接到2个千兆管理交换机，2个万兆网口分别连接到2个万兆交换机。节点后面板介绍此图为DFS 2000系列后面板，实际节点后面板端口模块跟本图中的位置不太一样，但是各端口样式和和名称一样，供参考。加电测试检测电源并进行设备加电测试，确认节点正常启动，无红灯报警，机柜电流指示正常。2.3、集群存储初始化集群初始化使用串口登录第一个节点，登录端口设置信息如下：Setting ValueTransfer rate 115,200 bpsData bits 8Parity NoneStop bits 1Flow control Hardware打开连接，根据客户提供的基本信息（集群名称，root密码，admin密码，SmartConnect IP，SmartConnect zone name，网络配置信息，DNS，NTP Server）按照向导完成集群的创建和初始化。select an option: 1 Create a new cluster 2 Join an existing cluster 3 Exit wizard and configure manuallyWizard Please select an option.Select an option: 1 Create a new cluster 2 Join an existing cluster 3 Exit wizard and configure manuallyWizard 1 zjbc-DFS Encoding set to utf-8Configure interface int-a: 1Enter a new netmaskConfigure int-a netmask 255.255.255.0Configure interface int-a: 1 Configure netmask 2 Configure int-a IP ranges Enter Keep the current configuration: Netmask: 255.255.255.0 IP ranges: (not set)Configure interface int-a 2Configure int-a IP ranges 1 Add an IP range 2 Delete an IP range Enter Keep the current IP ranges: IP ranges: (not set)Configure int-a IP ranges 1Enter the low IP address of the range to add:Low IP address (add) 10.10.0.1Enter the high IP address of the range:High IP address (add) 10.10.0.100Configure int-a IP ranges 1 Add an IP range 2 Delete an IP range Enter Keep the current IP ranges: IP ranges: 10.10.0.1-10.10.0.100Configure int-a IP ranges Configure interface int-a: 1 Configure netmask 2 Configure int-a IP ranges Enter Keep the current configuration: Netmask: 255.255.255.0 IP ranges: 10.10.0.1-10.10.0.100Configure interface int-a Select the internal interfaces to configure 1 int-a - primary internal interface 2 int-b - secondary internal interface (failover) Enter Exit configuring internal interfacesConfigure internal interfaces 2Configure interface int-b (failover): 1 Configure netmask 2 Configure int-b IP ranges 3 Configure failover IP ranges Enter Keep the current configuration: Netmask: (not set) IP ranges: (not set) Failover IP ranges: (not set) Failover: disabledConfigure interface int-b (failover) 1Type a new netmaskConfigure int-b netmask 255.255.255.0Configure interface int-b (failover): 1 Configure netmask 2 Configure int-b IP ranges 3 Configure failover IP ranges Enter Keep the current configuration: Netmask: 255.255.255.0 IP ranges: (not set) Failover IP ranges: (not set) Failover: disabledConfigure interface int-b (failover) 2Configure int-b IP ranges 1 Add an IP range 2 Delete an IP range Enter Keep the current IP ranges: IP ranges: (not set)Configure int-b IP ranges 1Enter the low IP address of the range to add:Low IP address (add) 10.10.1.1Enter the high IP address of the range:High IP address (add) 10.10.1.100Configure int-b IP ranges 1 Add an IP range 2 Delete an IP range Enter Keep the current IP ranges: IP ranges: 10.10.1.1-10.10.1.100Configure int-b IP ranges Configure interface int-b (failover): 1 Configure netmask 2 Configure int-b IP ranges 3 Configure failover IP ranges Enter Keep the current configuration: Netmask: 255.255.255.0 IP ranges: 10.10.1.1-10.10.1.100 Failover IP ranges: (not set) Failover: disabledConfigure interface int-b (failover) 3Configure failover IP ranges 1 Add an IP range 2 Delete an IP range Enter Keep the current IP ranges: Failover IP ranges: (not set)Configure failover IP ranges 1Enter the low IP address of the range to add:Low IP address (add) 10.10.2.1Enter the high IP address of the range:High IP address (add) 10.10.2.100Configure failover IP ranges 1 Add an IP range 2 Delete an IP range Enter Keep the current IP ranges: Failover IP ranges: 10.10.2.1-10.10.2.100Configure failover IP ranges Configure interface int-b (failover): 1 Configure netmask 2 Configure int-b IP ranges 3 Configure failover IP ranges 4 Disable failover Enter Keep the current configuration: Netmask: 255.255.255.0 IP ranges: 10.10.1.1-10.10.1.100 Failover IP ranges: 10.10.2.1-10.10.2.100 Failover: enabledConfigure interface int-b (failover) Select the internal interfaces to configure 1 int-a - primary internal interface 2 int-b - secondary internal interface (failover) Enter Exit configuring internal interfacesConfigure internal interfaces Configure external subnet 1 ext-1 - External interface Enter Exit configuring external network.Configure external subnet 1Configure interface ext-1: 1 Configure netmask 2 Configure MTU 3 Configure ext-1 IP ranges Enter Keep the current configuration: Netmask: (not set) MTU: 1500 IP ranges: (not set)Configure interface ext-1 1Enter a new netmaskConfigure ext-1 netmask 255.255.255.0Configure interface ext-1: 1 Configure netmask 2 Configure MTU 3 Configure ext-1 IP ranges Enter Keep the current configuration: Netmask: 255.255.255.0 MTU: 1500 IP ranges: (not set)Configure interface ext-1 Enter default gateway:Configure default gateway 10.15.80.254Configure SmartConnect settings 1 SmartConnect zone name 2 SmartConnect service IP Enter Keep the current SmartConnect settings: SmartConnect zone name: (not set) SmartConnect service IP: (not set)Configure SmartConnect settings Configure DNS settings 1 DNS servers 2 Search domains Enter Keep current DNS settings: DNS servers: (not set) Search domains: (not set)Configure DNS settings Configure external subnet 1 ext-1 - External interface Enter Exit configuring external network.Configure external subnet 1Configure interface ext-1: 1 Configure netmask 2 Configure MTU 3 Configure ext-1 IP ranges Enter Keep the current configuration: Netmask: 255.255.255.0 MTU: 1500 IP ranges: (not set)Configure interface ext-1 3Configure external IP ranges 1 Add an IP range 2 Delete an IP range Enter Keep the current IP ranges: IP ranges: (not set)Configure ext-1 IP ranges 1Enter the low IP address of the range to add:Low IP address (add) 10.10.28.170Enter the high IP address of the range:High IP address (add) 10.10.28.189Configure external IP ranges 1 Add an IP range 2 Delete an IP range Enter Keep the current IP ranges: IP ranges: 10.10.28.170-10.10.28.189Configure ext-1 IP ranges Configure interface ext-1: 1 Configure netmask 2 Configure MTU 3 Configure ext-1 IP ranges Enter Keep the current configuration: Netmask: 255.255.255.0 MTU: 1500 IP ranges: 10.10.28.170-10.10.28.189Configure interface ext-1 Enter default gateway:or press Enter to keep the current gateway: 10.10.28.254Configure default gateway Configure SmartConnect settings 1 SmartConnect zone name 2 SmartConnect service IP Enter Keep the current SmartConnect settings: SmartConnect zone name: (not set) SmartConnect service IP: (not set)Configure SmartConnect settings Configure DNS settings 1 DNS servers 2 Search domains Enter Keep current DNS settings: DNS servers: (not set) Search domains: (not set)Configure DNS settings Configure external subnet 1 ext-1 - External interface Enter Exit configuring external network.Configure external subnet Configure cluster date and time 1 Configure time zone 2 Configure day and time Enter Keep the current date and time: 2012/01/12 05:06:25 UTC.Configure date 1Configure cluster time zone 1 Greenwich Mean Time 2 Eastern Time Zone 3 Central Time Zone 4 Mountain Time Zone 5 Pacific Time Zone 6 Arizona 7 Alaska 8 Hawaii 9 Japan 10 Advanced Enter Keep current time zone: Greenwich Mean TimeConfigure time zone 10AdvancedTime zone set to Asia/Shanghai.Configure cluster time zone 1 Greenwich Mean Time 2 Eastern Time Zone 3 Central Time Zone 4 Mountain Time Zone 5 Pacific Time Zone 6 Arizona 7 Alaska 8 Hawaii 9 Japan 10 Advanced Enter Keep current time zone: AdvancedConfigure time zone Configure cluster date and time 1 Configure time zone 2 Configure day and time Enter Keep the current date and time: 2012/01/12 13:06:39 CST.Configure date Configure cluster join mode 1 Manual 2 Secure Enter Keep the current join mode: ManualConfigure join mode Join mode set to Manual.You have made the following configuration changes:Cluster name : (not set) - zjbc-DFSEncoding : (not set) - utf-8int-a : enabled - enabledint-a netmask : (not set) - 255.255.255.0int-a IP ranges : (not set) - 10.10.0.1-10.10.0.100 int-b : disabled - enabledint-b netmask : (not set) - 255.255.255.0int-b IP ranges : (not set) - 10.10.1.1-10.10.1.100 lpbk : disabled - enabledlpbk netmask : (not set) - 255.255.255.0lpbk IP ranges : (not set) - 10.10.2.1-10.10.2.100 External netmask : (not set) - 255.255.255.0External IP range: (not set) - 10.10.28.170-10.10.28.189External gateway : (not set) - 10.10.28.254Time zone : Greenwich Mean Time - AdvancedCurrent date/time: 2012/01/12 05:06:46 GMT - 2012/01/12 13:06:46 CSTDo you wish to commit these changes? yesCommit changes? yesPre-IFS daemons: isi_watchdog_d isi_hangdump isi_eth_mixer_d isi_flexnet_d.Mounting NFS file systems:.Initial amd64 initialization:.Additional ABI support:.Clearing /tmp (X related).isi_drive_d successfully startednfsd_mntinit() set the dispatch tableStarting xinetd.Starting local daemons:.Updating motd.Configuring syscons:.Starting cron.machdep.DFS_hw_monitor: 1046271 - 1046271start sshd via isi_run for AV_COMPLY process flagChecking DFS SAS PHY Hardware: goodDongle serial number: SX200-301135-0010Dongle system configuration: 400-0034-02Configuring console port baudrate. 115200isi_sasphymon successfully startedLogging to /var/log/isi_rpc_dRunning isi firmware status -saveMounting IFS filesystem.-/dev/da12s1e-/dev/da11s1e-/dev/da10s1e-/dev