4070陶粒砂MSDS.doc

GZLH.IHP (All Mesh Sizes)MSDS NO: 02Revision Date: August 22, 2013Material Safety Data SheetSECTION I - Product and Company IdentificationTrade Name:Ceramic ProppantSynonym(S):Ceramic Proppant; Semi-Crystalline Alumina SilicateChemical Family:AluminosilicateManufacturer:Shandong Kerui Petroleum Equipment CO.,LTD, ShanDong Province, ChinaPhone: 86mergency Phone:8624-Hour)FAX:+86-546-8179681SECTION II - Composition/Information on IngredientsIngredientsCAS NumberConcentrationClassificationR-PhrasesCorundum1302-74-540-60%Not ClassifiedNot assignedMullite1302-93-840-60%Not ClassifiedNot assignedSECTION III Physical/Chemical CharacteristicsBoiling Point:Not applicableMelting Point:Not applicableVapor Density(Air=1):Not applicableVapor Density:Not applicableVapor Pressure(mm Hg):Not applicable%Solubility In Water:Insoluble at 20%Solubility In sea Water:Insoluble at 20Specific Gravity(H2O=1):3.20 to 3.45Bulk Density:118 lb/cu.ft.Biodegradability:Not applicableEvaporation Rate:Not applicable (Butyl Acetate=1)Appearance:Gray to Beige Spherical PelletsOdor:OdorlesspH:NeutralVOC:NoneSECTION IV Health Hazard InformationHazardous Ingredient InformationHMIS RatingHealth:1.(slight)Flammability:0.(Minimal)Reactivity:0.(Minimal)Chronic:1.(slight)Potential Health EffectsInhalation:Prolonged exposure to dusts may cause respiratory tract irritation. Ingestion:NO known adverse effects.Eye Contact:May cause irritation on prolonged or repeated contact. Skin Contact:May cause irritation on prolonged or repeated contact.Special Protection:See Section IXSECTION V Emergency and First Aid MeasuresInhalation:Remove to fresh air. If irritation persists, call a physician.Ingestion:Procedures normally not needed. Seek medical attention if large quantities are ingested.Eye Contact:Immediately flush eyes with large amounts of water. Get medical attention if irritation persists.Skin Contact:Flush with plenty of water. If irritation persists, call a physician.SECTION VI Fire Fighting MeasuresFlash Point:Not applicableLower Explosion Limit:Not applicableUpper Explosion Limit:Not applicableAuto ignition Temperature:Not applicableSpecial Fire Fighting Procedures: This material does not give a flash point by conventional test methods. Use extinguishing agent suitable for type of surrounding fire.SECTION VII Accidental Release MeasuresSpill Procedures:Dust suppressing cleaning methods such as wet sweeping or vacuuming should be used to clean the work area. If vacuuming is used the vacuum must be equipped with a HEPA filter. Compressed air or dry sweeping should not be used for cleaning. Dust suppressing compounds may be used to clean up light dust. Use wet sweeping or a dust suppressant where sweeping is necessary.Release into Air:Prevent release of airborne particulates where possible. Not a regulated hazardous substance. See section IX for appropriate engineering controls.Release into Water:Release into water is not appropriate. Not a regulated hazardous substance. Landfill dusts and debris consistent with local regulations.SECTION VIII Handling and StorageStorage: These materials are stable and may be stored in a dry place indefinitely. Physical abrasion may produce small amounts of respirable dusts.Normal Use: Materials are stable under normal use and are not expected to produce significant hazardous by-products or emissions.SECTION IX Exposure Controls / Personal ProtectionExposure Limits:INGREDIENTSOSHA PEL-TWAACGIH-TWA TLVCorundum15mg/m3 (Total)5mg/m3 (Respirable)10mg/m3 (Total)3mg/m3 (Resp)Mullite15mg/m3 (Total)5mg/m3 (Respirable)10mg/m3 (Total)3mg/m3 (Resp)Engineering Controls: Use dust suppression controls. Local exhaust ventilation, point of generation dust collection, and/or down-draft work stations to minimize airborne dust generation are recommended when machining product.Respiratory Protection: Use appropriate protection pursuant to OSHA 29CFR 1910.134 and 29CFR 1926.103. The following information is provided as a guide and reflects industry recommendations for control of dust.Skin Protection: Wear gloves, head coverings, and full body clothing to prevent skin irritation. Disposable clothing may be used. Store work clothes and street clothes separately.Eye Protection: Wear safety glasses or chemical goggles to prevent eye contact. Do not wear contact lenses unless chemical goggles are also worn. Do not touch eyes with soiled body parts or materials. Have eye washing facilities readily available where eye contact can occur.SECTION X Stability and ReactivityStability: Materials are stable.Chemical Incompatibilities:Powerful oxidizers; fluorine, chlorine trifluoride, manganese trioxide, oxygen difluoride, etc.Hazardous Decomposition Products: NoneHazardous polymerization:Not ApplicableSECTION XI ToxicologyEpidemiology: N/AToxicology: N/ASECTION XII Ecological InformationEcotoxicological Information:No information available.Distribution: Aluminum oxide and silica are naturally occurring and are widely distributed in igneous rock. Secondary deposits in sedimentary rock may be found.Chemical Fate Information:The relative inertness of these materials indicates that they may be highly persistent in the environment. No information regarding any negative effects of this persistence has been noted.SECTION XIII Disposal InformationDisposal: Consult with local, state and federal regulations. In most cases these materials may be land filled safely.Hazardous Waste Classification:Subject to SARA Title III Notification.Empty Containers: Empty containers may contain product dust or residue. Do not re-use.Disposal regulations vary. Consult with all applicable regulations prior to disposal.SECTION XIV Transportation InformationNot regulated hazardous substances, no specific regulations apply.SECTION XV Regulatory InformationSARA TITLE IIISection 302:NoneSection 312: NoneSection 313:NoneToxic Substance Control Act (TSCA): N/ACERCLA Reportable Quantity:NoneClean Air Amendments-Hazardous Air Pollutants: NoneCalifornia State Proposition 65: N/ASECTION XVI OtherThe information contained herein is based on data considered to be accurate as of the preparation or revision date. It is provided in good faith and in compliance with state and federal regulations. No warranty