SL-3B30Q20-11.doc

产品规格书产品名称：5瓦COB LED产品规格书SPECIFICATION客户名称 Customer：产品名称Name： 圆形3W COB LED产品型号 Model：打印日期 Print Date： 2014-8-19客 户 确 认 Customers confirmation研 发 中 心 R&D Center批 准 Approval审 核 Audit制 定 Formulate一、 特点Characteristics：l 亮度高，光衰低 High brightness，low optical attenuationl 功耗低，寿命长 Low power, long lifel 散热快，结构紧凑 Heat faster, compact structurel 可靠性高 High reliability二、 用途Application： 家居照明，户外照明等。Residential lighting, outdoors lighting, etc三、 极限参数Limit Parameters（TA=25）：ParametersMINMAXUnit正向电流 Positive Current IF/400mA正向脉冲电流 Positive Pulse Current IFP*/600mA工作温度 Working Temperature TOPR-10+85贮存温度 Storage Temperature TSTG-40+85最大功耗 Maximum Power Consumption PD/9000mW *注：脉冲宽度0.1ms，占空比1/10。Note: Pulse width is 0.1 ms. Duty Ratio is 1/10 四、 光电参数The Photoelectricity Parameter（TA=25）：Parameter NameConditionsUnitMINTYPMAX正向电压 Forward Voltage VFIF=300mAV131518色度坐标 Chromaticity CoordinatesXIF=300mA-0.31-Y-0.33-光通量 Luminous Flux IF=300mAlm-450-五、 外形尺寸Shape Dimension：外观图：原理图：芯片新世纪20*20芯片新世纪20*20六、 特性曲线Characteristic Curve： 七、 使用注意事项Cautions：1） 静电Static Electricity：本产品对静电敏感，所以在使用本产品时必须采取有效的防护措施。尤其是静电产生的高压电流超过产品的最大额定值，会引起产品的损坏，或者可能使到产品完全失效。客户使用产品时，应采取安全的防止静电和电涌的对应措施。接地电阻10欧。使用防静电手环，防静电垫子，防静电工作服和工作鞋，手套和防静电容器，都是有效的防止静电和电涌的对应措施。烙铁点应正确接地。You need to take the protective measures for the product being sensitive to static electricity. It can lead to product damage or even the total invalid When the high voltage current made by static electricity is beyond the maximum rating. The ground resistance cant beyond 10By using anti-static-electricity bracelets/ cushions/ overalls/ shoes/gloves and anti-static-electricity containers, it can effectively prevent static electricity and surge.The soldering iron point should be properly grounded.2） 焊接soldering：a， 使用烙铁人手焊接Use soldering by hand：推荐使用少于20W的烙铁，而且烙铁的温度必须保持不高于300，一次焊接时间不超过3秒。Recommend using soldering iron which power is less than 20W and temperature is not higher than 300 . Soldering time is not more than three seconds each time.3） 清洗Cleaning：在焊接后必须按照以下条件进行清洗。After the soldering, the cleaning need to made according to the following conditionsa， 清洗剂：异丙醇或者工业酒精（95以上）cleaning agent:Isopropanol or industrial alcohol (95 )。b， 温度：30秒 最高50 或者 3分钟 最高30 Temperture limite: When the cleaning time is in the 30 seconds , the temperature cant higher than 50 , if it is in the 3 minutes, the temperature cant higher than 30.c， 超声波清洗：最大300W。 Ultrasonic cleaning: MAX 300W4） 其他事项Others.a. 任何时候请勿触碰胶体部分，以免产品表面不良甚至失效。Any time, dont touch colloid part, lest product surface come to be damaged or even invalid.b. 储存环境湿度小于50%，温度应保持恒定，避免超过20的温度变化。The storage environment humidity should less than 50% and the temperature should be constant, which will lead to avoid the temperature changes n