常用中英文对照表.doc

常用中英文对照表 1 of 41.材料:英文中文ACRYLIC亚加力(黑色.白色.茶色)AL 6061(ALUMINIUM ALLOY 6061)轻铝(飞机铝)AL 7075(ALUMINIUM ALLOY 7075)高强度超硬铝ANTI-STATIC DERLIN / ESD225 / ESD420防静电塑料BRASS黄铜BRONZE青铜BLACK CONDUCTIVE PLASTIC黑色的可传导塑料BAKELITE电木COPPER(CU)红铜CERAMICS陶瓷DF-2油钢( 供淬火用,淬火后生锈)DISK MATERIAL磁碟材料(特级轻硬铝)DERLIN : White / Black赛钢( 白色,黑色)GLASS玻璃H,S,S生钢NYLOM尼龙PVC聚氯乙烯塑料RUBBER橡胶S 1000 (ENGINEERING PLASTIC )工程塑料(棕色)SUS 303 / SUS304 / SUS 316 / SUS 318/S440C不锈钢S136S136H不锈铁TEFLON铁氟隆,聚四氟乙烯塑料XW-41铬钢( 供淬火用,淬火后不生锈)2.螺纹:英文中文BSF (BRITISH STANDARD FINE THREAD)英国细牙螺纹标准BSP (BRITISH STANDARD PIPE THREAD)英国管螺纹标准BSW(BRITISH STANDARD WORTH THREAD)英国惠氏标准螺纹BSD (BRITISH STANDARD DIMENSION)英国度量标准尺寸BSG (BRITISH STANDARD GAUGE)英国标准线规BSS (BRITISH STANDARD SPECIFICATION)英国标准技术规格UNC (UNITED COARSE THREAD)统一标准粗牙螺纹UNF (UNITED FINE THREAD)公称细牙UNEF(UNITED EXTREME FINE THREAD)公称极细牙M ( Metric )公制螺纹SCR(Screws) or Bolt螺丝,螺栓.Major diameter螺纹大直径Minor diameter螺纹小直径TAP攻螺纹.Screw DIE螺丝扳牙Screw TAP螺丝攻牙Pitch螺距RH(Right hand)右旋LH(Left hand) or Levorotation左旋NPT国家管用螺纹(美制,斜牙)G 美制标准管牙 常用中英文对照表 2 of 43.热.表面处理:英文中文HRC60热处理洛氏硬度60Cr PLATED镀铬Ni PLATED镀镍HARD BLACK ANODIZE硬黑HARD WHITE ANODIZE硬白HARD CHROME镀硬铬HARDENED 淬火( 硬 )NITRONDING氮化Ti-NITRONDING氮化钛Zn PLATED镀锌Ag PLATED镀银Au PLATED镀金Passivation钝化4.常见英文:英文中文CBORE (Counter bore)平底孔CSINK (Counter sink)埋头锥孔CL (Center line)中心线CYL (Cylinder or cylindericl)圆柱DIA (Diameter)直径DWG . NO (Drawing number)图纸编号ENGR (Engineer)工程师INT (Intermal)内EXT (External)外PCD (Pitch circle diameter)节圆直径S . F (Slide fit)滑配F . F (Force fit)压配P . F (Press fit)紧配REV (Revsion)版本S . (Spherical diameter)球面直径S . R (Spherical radius)球面半径S . S (Stainless steel) 不锈钢THRU (Through)穿通TOL (Tolerances)公差UCUT (Under cut)空刀槽MATL (Material)材料S .FACE (Spot face)刮平A .F (Acaoss flats)对边SHT X OF X (Sheet x of x ) 第x张共x页 0.09 THRU ( 2X )表示两个直径为 0.09 的通孔 0.40 DEEP 0.125表示直径为 0.4 深 0.125 的孔 3.0 HOLE BE DONE IN ASSEMBER 3.0 的孔装配后加工 5.2 THRU & CBORE 8.0 DEEP 5.0 5.2 的钻通和 8.0 的平底孔深 5.0C (Chamfer)倒角R (Radius)半径 常用中英文对照表 4 of 44.常见英文:英文中文RETAIN THESE SHARP EDGES保持这些边为锐边THRU TO HOLE通到孔(表示一孔与另一孔相通)MAX最大MIN 最小ALL DIMENSIONS ARE FINISHED DIMENSION (AFTER ANODIZE)所有尺寸是表面处理(加电镀层)后的尺寸UNLESS OTHER WISE SPECIFIED ALLCHAMFER TO BE 0.05除非另有说明,所有倒角为0.05THIS SIDE R2 ANOTHER SIDE ALL SHARP EDGES标箭头这边倒 R2 圆角,其它边保持锐边UNLESS OTHERWISE SPECIFIED ALLDIMENSION ARE IN MM (INCHES)除非另有说明,所有尺寸以毫米 (英寸)为单位 常用中英文对照表 3 of 44.常见英文:英文中文CHAMFER ALL AROUND 0.05所有的倒角为 0.05 0.5 DEEP 0.25直径为 0.5 深 0.25 的孔 0.25 THRU ( 2X )两个直径为 0.25 的通孔TAP # 8-32 UNC THRU攻通 # 8-32 标准粗牙螺纹QTY: 10 EA / SET数量 : 10件 / 套NO CHAMFER不倒角KEEP SHARP EDGE保持锐边UNIT : MM ( INCH )单位 : 毫米 ( 英寸 )DEEP深EQUIPARTION均等,均布KNURLING滚花OTHER SIDE另一边,另一面LENGTH长度DOWEL PIN销钉SEE DETAIL ( SEE SHOW )看详细说明DRILL钻孔SLOT槽,狭长开口PITCH DIMENSIONS间隔距离DETAIL详细表示ANGULAR角度公差ALIGEWD SECTION定线剖切图LASER MARK激光刻字CIRCLE圆DVEVLOPMET展开图ELLIPSE椭圆ELEVATION立视图ENLARGEMENT放大END ELEVATION侧面图HALF SECTION半剖HOLE孔LOCAL SECTION局部剖视图THICKNESS厚度ALL GRINDING所有表面磨削加工SECTION VIEW ON A-AA-A 剖视图PIN销SURFACE GRINGING表面磨光FILL