丙烯酸铁红底中涂漆的用途.doc

Intended Uses用途适用于工程机械、机床、电机、五金器件、建筑钢结构等用作底漆或中涂漆As primer or intermediate coat, used for engineering machine,machine tool, electric machine, hardware parts and architectural steel structures etc.ProductInformation产品简介干燥快。能在低温中施工、能抵抗弱化学品飞溅，具有优异的抗腐性能。Short drying time, May be applied at low temperature.Its film may counteract splash of weak chemical, and therefore possesses excellent resistance to corrosionApplication details产品数据Volume Solids 固体份Around 48% 约48% Dry Flm Thickness干膜厚度40-60microns 40-60微米Theoretical Coverage 理论涂布率7.5m2 /Kg 7.5平方米/公斤Practical Coverage 实际涂布率Allow appropriate loss 允许适量损耗Storage and Handling施工详述Mix Radio 混合比One package 单罐装Method of Application 施工方法 Airless Spray 无空气喷涂 Recommended 推荐采用 Brush or Roller 涂刷或辊涂 Recommended 推荐采用 Conventional Spray 传统喷涂 Recommended 推荐采用Thinner 稀释剂 SC001Cleaner 油漆设备清洗剂 SC001Pot Life 使用期 Not limit 没限制Drying time 干燥时间SubstrateTemperature底材温度Touch Dry 表干（min）Hard Dry硬干（h）Over coating Interval覆涂间隔 Min最短Max最长35155 10 2030412244hours 小时8hours 小时12hours 小时Not limit 没限制丙烯酸铁红底/中涂漆的用途StorageandHandling贮存与管理Storage 贮存 dry and cool conditions away from fire and heat source 贮存于阴凉干燥处 Pack size 包装规格 25Kg in 20 liter container 25公斤装于20公升容器Flash Point 闪点 28Specific Gravity 比重 About 1.28Kg/L 约 1.28公斤/公升 Specification and Surface preparation技术要求及表面处理When used as primer: New steel structure must be blasted to be in acordance with Sa2.5 Standard or rustremoved with power tools to reach St3 grade ,Wash grease away with solvent, Keep the surface to be paint clean and dry.When applied as intermediate coat: Suitable preceding coat: Epoxy primer, Chlorinated rubber primer series, and vinyl primer series etc.Surface to be painted should be clean and drySuitabbe Subsequent Coat: A crylic resin based finishing paint.用作底漆：新建钢结构需经喷砂处理达 Sa2.5级或动力工具除锈达 St3级，用溶剂去除油污，保持表面清洁干燥用作中途漆：合适的前涂层包括环氧底漆、氯化橡胶类底漆、乙烯类底漆等、表面保持清洁干燥，合适后涂层为丙烯酸树脂面漆。 Safety Precautions 安全措施This product should be used in painting area by perfessional operators. When painting , please refer to Product Data Sheet and MSDS. Consult our company if consumers could not completely understand the precautions for safety and health when applying this product.This product is a kind of solvent-based paint .Inorder to avoid danger or accident, minimal safety precautions,as follow , should be down .The paint contains volatile solvent and is flammable . So must keep away from sparks and open flames.No smoking at applacation site ,Effective precautions (such as using explosion-proof electrical equipments. No static electricity accumulation or metal collision etc) also should be done so as to avoid producting sparks .Flash point of paint , mentioned above on product Data sheet, is the lowest temperature at which mixture of the volatile materails of paint can ignite or explode with air. Enough ventilation is necessary at application site. In order to remove any danger of explosion, must keep the ratio of gas to air is less than 10%, the minimum explosive limit in general, Therefore, 200m3 of ventilation quantuty per 1Kg solvent (according to the solvent ) is necessary.Product skin and eyes, and avoid touching with paints (Recommend to wear working clothes, gloves,eye protection, face masks barrier cream and so on ). Kif paint gets in touch with skin , wass fully with large amount of fresh water and soap or appropriate commercial cleaner. In case of eyes being contaminated, rinse with fresh water for 10min at least and give medical treatment immediately. Recommend face guard with ventilation pipe for the sake of no absorption of paint fog and harmful solvent gas, especially in bad ventilation.Handle empty containers with care and do not bring about environmental contamination.NOTICE: If consumers have not taken effective safety precautions(Refer to the specfications), our company will NOTbe responsible for any accident. 本产品由专业人缘在工业场所使用,使用时请参照本说明书及健康安全手册,如客户在使用本产品前,未能仔细了解有关产品的健康安全知识,请与本公司联系.该涂料为溶剂型涂料,为避免事故或危险发生,应采取最低限度的安全措施如下:此涂料为易燃物,并含有挥发性易燃溶剂,故必须远离火星和明火,严禁在作业场所吸烟,并采取有效措施,防止火星产生(如采用防爆电器设备,杜绝静电积累,避免金属撞击等)本产品说明书中所列涂料及溶剂的闪点是引起燃烧的最低温度. 施工场所应尽量进行通风良好,为消除使用过程中的爆炸隐患,应保证足够的通风量以维持气体/空气比例不超过最低爆炸极限的10%,通常每千克溶剂需要200立方米通风量,(与溶剂种类相关)就能维持最低爆炸极限10%的工作环境.