2100标准型圆锥破碎机设计【含11张CAD图纸+PDF图】
收藏
资源目录
压缩包内文档预览：
编号：126135247
类型：共享资源
大小：3.08MB
格式：ZIP
上传时间：2021-05-06
上传人：好资料QQ****51605
认证信息
个人认证
孙**（实名认证）
江苏
IP属地：江苏
45
积分
- 关 键 词：
-
2100
标准型
圆锥
破碎
设计
11
CAD
图纸
PDF
- 资源描述：
-
喜欢这套资料就充值下载吧。资源目录里展示的都可在线预览哦。下载后都有，请放心下载，文件全都包含在内，有疑问咨询QQ:1064457796或1304139763
- 内容简介：
-
鞍山科技大学本科生毕业设计（论文） 第1页THE SELF-GRINDING MECHANISM AND AFFECTING FACTORS OF BULK MATERIAL IN FLUID MOTIONAbstract: The fluidity and classfication of bulk material (loose body) were introduced, the self-grinding mechanism and the affecting factors bulk materials in various forms of phase, state and motion were investigated. A rotational-flow-state centrifugal autogenous grinder was developed on the basis of applying self-grinding mechanism of bulk material, the result tested by the autogenous grinder was compared with extremely high specific area were obtained. The feasibility lf the developed new-type artogenous grinder in the view of fluid motion of bulk material was proved.Key words: motion of bulk material; self-grinding mechanism; new developed mill1 IntroductionComminution except coarse grinding in most commintors or crushing machines is performed in the course of motion of bulk materials. Only in a few comminting equipments such as rollermill and extruding milll, the vomminuted materials are stationary or fluid motion was provided through grasping the characteristic of fluid motion in the course of comminuting.2 Fluid Motion of Bulk Materials2.1Fluidity of bulk materialsIn unconsolidated media mechanics, bulk material is also named loose body, it is the aggregate of interrelated solid particles, where a single particle presents the characteristic of solid and is the skeleton of the loose body. However, in macroscopic view, it also presents fluidity and some characteristics of liquid: (a) being the same with liquid, bulk material can not keep a certain shape; (b) both bulk material and liquid can not bear a tension force but bear a pressure force. The difference between bulk material and liquid is that there exists an inner friction (inner friction angle) in the bulk material. This is to say, if an external condition is exerted on bulk material to alleviate or eliminate the inner friction angle, the bulk material will be fluidized. For example, adding some media such as water and colloid materials to bulk material or exerting special external forces (resonant force etc.) on bulk material, the bulk material can be fluidized.2.2 Affecting facters of bulk material motionAs stated above, the most predominant factor affecting the motion of bulk material is the existence of inner friction angle. The smaller the inner friction angle is, the easier the motion of bulk material becomes. In the conctrte, the factors can be: (a) the lumpiness of single particle in bulk material, the lumpier the particle is, the more difficult the motion of bulk material will be;(b) the unit weight of bulk material, the beavier the rnit weight is, the more difficult the motion will be;(c) the looseness (porosity) of bulk material, the looser the bulk material is, the easier the motion will be;(d) the humidity of bulk material, bulk material starts to flow when the humidity exceeds a critical, whereas, for some bulk materials, the increment in humidity conversely brings about the increment of inner friction angle and leads it difficult to flow;(e) the morphology and surface roughness of single particle, the inner friction angle is colsely related to the morphology and roughness of particle of bulk material;(f) it is more difficult for momideal bulk material to flow than for ideal bulk material to.2.3 Classification of fluid motion of bulk materialThe fluid motion of bulk material can be classified according to whether there is energy-carrier medium or not:() Single-phase flow. When there is not energy-carrier medium in the bulk material, or there are media, for example, air and water, but the media do not play the role of energy-carrying, the flow is all regarded as single-phase flow.() Biphase flow, when there are quantities of energy-carrier media in the bulk material, the particles of bulk material are suspending or near to suspending, the flow is biphase flow.The flow velocity of bulk material is an impoetant parameter for self-grinding. According to the velocity, the fluid motion can be classified:() ultimate low velocity (9m/s); () low velocity (9100m/s);() medium velocity (20100m/s);()high velocity (100200m/s); () ultrahigh velocity (2501000m/s). The efficiency of self-grinding is very low when the flow velocity is in the ultimate low velocity range, the velocity is hardly chosen as a parameter in autogenous grinder. The low velocity is often chosen as a parameter in horizontal cylindrical autogenous grinders. The medium velocity is usually chosen as a parameter in vertial shaft centrifugal comminutors, and high velocity and ultrahigh velocity are adopted in ultrafine comminution.3 Analysis of Fluid Motion Mechanisn3.1 Classification of self-grinding modesThe self-grinding modes of fluid motion can be classified into:(a) impact self-grinding. In this mode, particles collide each other and reduction takes place;(b) delaminating self-grinding. Particles impact and shear each other, the particles are delaminated and reduction take place;(c) fatigue rupture self-grinding. Materials are fatigued to rupture under the condition of high-frequency altenating pulse stresses. The fatigue rupture self-grinding can make tough mateials to be comminuted in the way in which brittle materials are comminuted.3.2 Analysis of self-grinding mechanismThe flowing forms of every kinds of bulk materials are composed of two basic flowing forms:linear flow and rotational flow. In practice, an independent flowing form is usually present in grinding machine, in a very few case, two flowing forms are compositely present in centrfugal autogenous grinder. Hence, respectively studying the self-grinding mechanism of the two basic flowing forms is the basis for investigating the self-grinding mechanism of bulk material. Moreover, difference in phase and state of flowing bulk material must also be considered.3.2.1 linear flow(a) Single-phase linear flow. The forms of self-grinding are impacting and delaminating of particles. For example, he principle of vertical shaft impact comminutor is that a strong centrifugal force field caused by a high-speed rotating centrifugal disk brings about a high-speed linear jet of bulk material, the jet collides and impacts the particles remained the wall of cylinder. Meantime, the difference in velocity of jet particles caused by different sizes and morphologies also brings about impacting and delaminating of particles, but the degree of wearing and delaminaing is limited.(b) Biphase linear flow. Similar to flow of liquid, the biphase linear flow also includes laminar flow and turbulent cuttent. The flow is stable when it is in the district of laminar flow, the velocity of particles in a layer is same but that in various layers is different. The friction of particles between different layers takes place. However, as well-known, the flow velocity in laminar flow district is very low, so the degree of self-grinding caused by laminar flow is limited.The comminution mainly takes place in the district of turbulent vurrent due to higher or very high velocity of current and occurrence of violent turbulence in the district. Violent collision between particles exists in the trubulence, and impact comminution is formed. If several jets intersect each other, the intersected particles will violently collide and impact. The higher the velocity is, the more efficient the self-grinding will be. For example, air-current comminutor works in gas-solid biphase self-grinding.3.2.2 Rotational flowRotational flow is formed by an external force such as in an anular pipe and cylindrical container. The centrifugal force field caused by rotating flow radially acts on the particles, the particle jet pressures the walls of pipe or container and particles remained on the walls, thus lesds to friction and shear force between the particles. The peculiar shear force in rotational flow is a predominant factor contributing self-grinding.(a) Single-phase rotational flow. The state and velocity of each particle of bulk material are different owing to the difference in size and morphology of each particle. Consequently, the fricting shear force between particles caused centrifugal pressure is a kind of alternating and pulse stress, the higher the flowing velocity is, the higher the altermating frequency and intension wil be. The high-frequency alternating and pulse shear stress make particles fatigue ruptured, the fatigur rupture which is expressed as brittle fatigue comminution is also a predominant form of self-grinding in rotational flow.(b) Biphase rotational flow. The self-grinding foem stated in single-phase flow above obviously is present in biphase flow. However, the self-grinding form is relatively weak owing to the fact that the viscid effect of energy-carrier medium hinders the flow of particles. Similar to those of biphase linear flow, the occurrence of violent turbulence ta high rotational velocity brings about the collision of particles and impact comminution is formed. The self-grinding form also occupies a place in biphase rotational flow.4 Factors Affecting Self-grindingOn the basis of analyses of comminution mechanism stated above, the factors affecting self-grinding can be summarized as following:(a) The instinctive structure and physical properties of bulk material such as fragility, hardness, brittleness, toughness, joint, cleavage and natural defects. All these factors are of importance to every comminution form. (b) The state of flowing. Linear flow and biphase rotational flow are applicable to brittle material, and single-phase rotational flow is applicable to tough material, the reason is that the high-frequency pulse shear effect renders tough material brittle failute. (c) The velocity of flowing. Whether in linear flow state or in rotation flow state, the velocity of flowing is one of the most important factors affecting the efficiency of self-giending. The higher the velocity is, the more efficient the self-grind will be, and the finer the obtained particles will be.(d) The concentration (for biphase flow) or the looseness(for single-phase flow). On the basis of probability theory, the increment in concentration raises the probability of collision between particles, thus improves the efficiency of comminution. Comsequently, increment in comcentration fo bulk material in biphase flow state and decrement in loosemess of bulk material in single-phase state are effective ways to improve the effectiveness of self-grinding.5 Practical Application A new-type rotational-flow-state centrifugal autogenous grinder has successfully developed by applying
- 温馨提示:
1: 本站所有资源如无特殊说明，都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等，如果需要附件，请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸，网页内容里面会有图纸预览，若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 人人文库网仅提供信息存储空间，仅对用户上传内容的表现方式做保护处理，对用户上传分享的文档内容本身不做任何修改或编辑，并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容，请与我们联系，我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。
人人文库网所有资源均是用户自行上传分享，仅供网友学习交流，未经上传用户书面授权，请勿作他用。
川公网安备: 51019002004831号