外销订单确认问题模板

1、1. 确认阻焊开通窗Question: As the picture below(请附图加以说明),the SMT is so close to each other, only 7mil（根据实际情况更改）,it is very difficult to keep the solder mask between the SMTSuggestion: no solder mask between SMT is OK.2. 确认板边削SMT或焊盘Question: As the picture below(请附图加以说明),the pads is so close to the outline.

2、Suggestion: shave the pads 7mil（根据实际情况更改）to avoid exposing copper.3. 确认板边露铜Question: As the picture below(请附图加以说明),the pads is so close to the outline.Suggestion: exposing copper is OK4. 图纸指示与GERBER文件指示尺寸不同Question: As the picture below(请附图加以说明),the dimension is different in the *.doc file（根据实际情况更改）

3、 and the gerber, please confirm.Suggestion: follow gerber.5. 孔径表与钻孔文件不符Question: the size (quantity) of the holes is different in the drill file and the drill table,such as T1 T2 （根据实际情况更改）please confirm.Suggestion: follow the drill file.6. 桥太小容易断板Question: as the picture below(请附图加以说明),the break aw

4、ay tab is only 0.5mm(根据实际情况更改)，the board will be broken very easily when manufacturing.Suggestion: change the break away tab from 0.5mm to 1.6mm(根据实际情况更改).7. 孔位图与钻孔文件不符Question: as the picture below(请附图加以说明),the drill file cannot match the drill drawing layer, please confirm which one the correct.Su

5、ggestion: follow the drill file.(若点图上的孔明显要钻出来的请建议按照点图制作)8. 标记问题Question: you request add UL+DATE and our companys logo in the bottom solder mask layer(根据实际情况更改), but the board is too small to add them.Suggestion1: we will only add UL+DATE.Suggestion2: we will add them in the break away frame.（注意如果是N

6、CAB的客户，请优先建议把标记加在附边上）9.字符模糊问题Question: the legend text is on the pads and we have no place to move.Suggestion: we will shave the legend to avoid them printing on the pads, please confirm that the obscure and fragmentary legend is OK.10.插件孔一面喷锡一面盖油，建议在盖油面加比定位孔大5mil的开窗。Question: as the picture below(请

7、附图加以说明)，there is no solder mask opening for these holes, then there will be solder mask in the hole.Suggestion: add solder mask opening for these holes, which are larger 5mil than the holes.11.部分说明文件不是英语Question: as the picture below(请附图加以说明)，the information is not English, we cannot understand.Sugg

8、estion: ignore it, or else please translate it into English or Chinese.12.客户要求只加UL或者94V-0，但是不允许加FP标记时Question: You request do not add manufacturer Logo ,add "94V-0"&"Date Code" ,but we registered our Logo and Rego number from Underwriters Laboratory ,the UL mark must include :FP Logo,UL,94V-0.(as the picture below请附整个标记的图片加以说明),so please confirm we should only add "Date Code" or add the full UL mark(as the picture shown) Suggestion: add the full UL mark13:客户要求加mark点和定位孔，但是没有提供具体位置Question: You request add fiducial mark and mou