捷豹JaguarXJ220模型制作过程参考模板

1、制作目标：1开前盖2开尾厢盖3开门4发动机、内饰等直做为主5整车主色为亮光黑200806171416468852.jpg (52 KBytes)2008-06-17 14:16:481 / 45200806171416127413.jpg (49 KBytes)2008-06-17 14:16:14发动机简单组装，没有改造200806171415400218.jpg (153 KBytes)2008-06-17 14:15:46200806171415218219.jpg (192 KBytes)2008-06-17 14:15:28200806171414563156.jpg (153 KB

2、ytes)2008-06-17 14:15:01分色不是很满意，凑合着吧200806171414199289.jpg (155 KBytes)2008-06-17 14:14:25200806171413258413.jpg (139 KBytes)2008-06-17 14:13:30200806171413558536.jpg (150 KBytes)2008-06-17 14:14:00发动机部分基本完成200806171411127842.jpg (141 KBytes)2008-06-17 14:11:17200806171413080411.jpg (141 KBytes)2008

3、-06-17 14:13:14猜猜这是干嘛？200806171409583613.jpg (137 KBytes)2008-06-17 14:10:03切割前先加固200806171409229831.jpg (135 KBytes)2008-06-17 14:09:27准备切割车门200806171410377043.jpg (137 KBytes)2008-06-17 14:10:42先用0.2口径钻头钻孔，再用刻刀和锯子切割，比较保险200806171408206475.jpg (145 KBytes)2008-06-17 14:08:25200806171424235200.jpg (

4、142 KBytes)2008-06-17 14:24:28200806171408510277.jpg (131 KBytes)2008-06-17 14:08:58车门的一部分切割完毕200806171407444109.jpg (157 KBytes)2008-06-17 14:07:49用郡士白补土填充钻口的齿纹车门分成两部分是版件的原因。这是另外一部分（与车体相连）的切割。刚开始也想用电钻先打洞，结果可能是版件太厚的原因，钻头断了5根，只有用刻刀和锯片一齐切，效果还可以，而且基本不用再上补土。切下整个门后车体连接十分脆弱，幸好之前已经加固（白色骨架部分）200807061044209

5、946.jpg (79 KBytes)2008-07-06 10:44:20200807061044030728.jpg (89 KBytes)2008-07-06 10:44:04200807061042354970.jpg (52 KBytes)2008-07-06 10:42:35200807061042080066.jpg (95 KBytes)2008-07-06 10:42:09把车门两部分粘接后，等牢固后再制作车门的转动装置200807061041357576.jpg (89 KBytes)2008-07-06 10:41:45200807061041146178.jpg (79

6、 KBytes)2008-07-06 10:41:15200807061040540323.jpg (80 KBytes)2008-07-06 10:40:58数码相机丢了，暂时用手机拍，不是很清晰。200807231812566324.jpg (368 KBytes)2008-07-23 18:12:56200807231812286965.jpg (353 KBytes)2008-07-23 18:12:28200807231812074756.jpg (346 KBytes)2008-07-23 18:12:07200807231811352499.jpg (357 KBytes)200

7、8-07-23 18:11:35200807231811155094.jpg (352 KBytes)2008-07-23 18:11:15200807231810493302.jpg (352 KBytes)2008-07-23 18:10:49200807231810262684.jpg (351 KBytes)2008-07-23 18:10:26200807231810045639.jpg (360 KBytes)2008-07-23 18:10:04200807231809416771.jpg (352 KBytes)2008-07-23 18:09:4120080723180920

8、3305.jpg (355 KBytes)2008-07-23 18:09:20200807231808532144.jpg (355 KBytes)2008-07-23 18:08:53200807231808303084.jpg (353 KBytes)2008-07-23 18:08:30200807231807596395.jpg (353 KBytes)2008-07-23 18:07:59200807231807223373.jpg (359 KBytes)2008-07-23 18:07:22200807231806496830.jpg (347 KBytes)2008-07-2

9、3 18:06:49200807231806192759.jpg (356 KBytes)2008-07-23 18:06:19200807231805303318.jpg (355 KBytes)2008-07-23 18:05:30200807231805007674.jpg (354 KBytes)2008-07-23 18:05:00200807231804223400.jpg (355 KBytes)2008-07-23 18:04:22200807231803594992.jpg (353 KBytes)2008-07-23 18:03:59200807231803433923.j

10、pg (360 KBytes)2008-07-23 18:03:43200807231803266365.jpg (347 KBytes)2008-07-23 18:03:26·完善车门200807241743373553.jpg (356 KBytes)2008-07-24 17:43:37200807241743112989.jpg (356 KBytes)2008-07-24 17:43:11200807241742501840.jpg (357 KBytes)2008-07-24 17:42:50200807241742316633.jpg (347 KBytes)2008-

11、07-24 17:42:31200807241742071986.jpg (355 KBytes)2008-07-24 17:42:07200807241741471472.jpg (358 KBytes)2008-07-24 17:41:47200807241741206944.jpg (349 KBytes)2008-07-24 17:41:20200807241740438606.jpg (350 KBytes)2008-07-24 17:40:43缝隙等胶水干透再用补土填；下一步准备切车前箱和车尾箱，先用流道做好车壳的支撑。切割尾箱与前箱200807262155151975.jpg (

12、352 KBytes)2008-07-26 21:55:15来张全家福200807262154573396.jpg (92 KBytes)2008-07-26 21:54:57车尾箱关节200807262154372243.jpg (93 KBytes)2008-07-26 21:54:37502粘上200807262154182563.jpg (94 KBytes)2008-07-26 21:54:18补上一个承托200807262153548952.jpg (94 KBytes)2008-07-26 21:53:54200807262153377581.jpg (94 KBytes)200

13、8-07-26 21:53:37用回形针做的轴200807262153173717.jpg (94 KBytes)2008-07-26 21:53:17定位200807262153033203.jpg (95 KBytes)2008-07-26 21:53:03假组后上502胶200807262152329726.jpg (92 KBytes)2008-07-26 21:52:32200807262152152977.jpg (91 KBytes)2008-07-26 21:52:15废弃的软盘驱动器，切割边角以作车前箱的活动关节定位200807262151381926.jpg (93 KBy

14、tes)2008-07-26 21:51:38200807262151210463.jpg (94 KBytes)2008-07-26 21:51:21200807262150552193.jpg (92 KBytes)2008-07-26 21:50:55200807262150136983.jpg (93 KBytes)2008-07-26 21:50:13用胶片制作关节200807262149203503.jpg (94 KBytes)2008-07-26 21:49:20200807262148593650.jpg (93 KBytes)2008-07-26 21:48:59上螺母后2

15、00807262148326569.jpg (93 KBytes)2008-07-26 21:48:32200807262148099555.jpg (91 KBytes)2008-07-26 21:48:09组装好的闭合状态200807262147349337.jpg (94 KBytes)2008-07-26 21:47:34前箱开启状态200807262146370249.jpg (90 KBytes)2008-07-26 21:46:37200807262147027595.jpg (93 KBytes)2008-07-26 21:47:02200807262146042522.jpg (91 KBytes)2008-07-26 21:46:04200807262144309211.jpg (93 KBytes)2008-07-26 21:44:30200807262144142843.jpg (90 KBytes)2008-07-26 21:44:14开启