配电箱工艺流程

1、家用配电箱的安装工艺Installation technology of household distribution box科技社制作2016尚德 尚能 永新 永动什么是配电板、配电箱？What is a Panel, distribution box?将测量仪器和控制、保护、信号等器件按一定规律安装在专业的板上，便制成配电板。将其装入专用的箱内，便成配电箱。Measuring instruments and control, protection, signal devices installed on a regular basis on professional boards, mad

2、e from the power distribution Board. Put it in a special box, into a distribution box配电箱的组成The composition of the distribution box配电箱是数据上的海量参数，一般是构成低压林按电气接线，要求将开关设备、测量仪表、保护电器和辅助设备组装在封闭或半封闭金属柜中或屏幅上，构成低压配电箱。正常运行时可借助手动或自动开关接通或分断电路。Distribution boxes are data on the mass parameter, usually constitute a

3、low-voltage forest according to the electrical wiring, requires that the switching device, measuring instrument, protect electrical and auxiliary equipment to assemble in enclosed or semi-enclosed metal cabinets or on the screen image, constitute a low-voltage power distribution box. Normal operatio

4、n can be realized by using manual or automatic switching on or off road.配电箱的一次元件有：空开，刀开，接触器，热继电器，等；面板上的二次元件有：电压表，电流表，转换开关，指示灯，按钮，等；柜内装二次元件有：中间继电器，时间继电器，等；辅助配件有：导线，端子，熔丝，等。 另外，有许多配电柜装有：PLC，变频器。Distribution box of a times components has: empty open, knife open, contact device, hot following electrical

5、,; Panel Shang of two times components has: voltage table, ammeter, conversion switch, led, button,; cabinet within loaded two times components has: Middle following electrical, time following electrical,; auxiliary accessories has: wire, Terminal, melt silk,. In addition, there are many electrical

6、cabinet contains: PLC and inverter.目前常用的家用配电箱Common household distribution box家用配电箱的作用Role of household distribution box作用：它是连接电源与用电设备的中间装置，它除了分配电能外，还具有对用电设备进行控制、测量、指示及保护等功能。Role: it is connected to the power supply and electrical equipment broker, outside of distribution of power, it also has the p

7、ower to control, measurement, indication and protection functions.合理的分配电能，方便对电路的开合操作。有较高的安全防护等级，能直观的显示电路的导通状态。便于管理，当发生电路故障时有利于检修。Reasonable distribution of electrical energy, convenient opening and closing of the circuit operation. High level of safety and protection, can directly display the conduc

8、ting State of the circuit. Ease of administration when the circuit down to overhaul.配电箱的原理The principle of distribution boxes配电箱是按电气接线要求将开关设备、测量仪表、保护电器和辅助设备组装在封闭或半封闭金属柜中或屏幅上，构成低压配电装置。正常运行时可借助手动或自动开关接通或分断电路。故障或不正常运行时借助保护电器切断电路或报警。借测量仪表可显示运行中的各种参数，还可对某些电气参数进行调整，对偏离正常工作状态进行提示或发出信号。常用于各发、配、变电所中。Distribu

9、tion boxes are based on electrical wiring switch equipment, measuring instruments, protection of electrical and auxiliary equipment Assembly in closed or semi-closed metal cabinets or on the screen image, constitute a low-voltage power distribution unit. Normal operation can be realized by using man

10、ual or automatic switching on or off road. Protection fault or abnormal operation with electrical cut off the circuit or the police. By measuring instruments can display various parameters for running, electrical parameter can also be adjusted to prompts signals or deviations from normal working con

11、ditions. Commonly used for each license, distribution, substations.一般家用配电板原理图General Household Panel schematic配电箱的安装工艺流程Distribution box installation process1.先将配电箱外壳固定在墙上（家庭配电箱配电箱不宜安装过高，一般安装标高为1.8米，以便操作）1. the first distribution box housing to the wall (household distribution box power distribution

12、 box should not be installed too high, generally installed 1.8 meters above sea level so that operations)2.然后将导轨固定在配电箱内2. and then Rack Mount distribution boxes3.然后将空开，插座按从左到右的顺序安装在导轨上3. then open, socket installed in order from left to right on the rail4.按照电路图开始接线4. in accordance with the circuit diagram start wiring（1）先接地线(1) ground wire（2）再接零线(2) the zero line(3)接着接火线(3). FireWire(4).最后接三相电源线(4). three-phase power supply line5.接线安装完成后，用万用表检测接线是否正确是否有短路，断路等情况。如确定没有错误后，合上空气开关，通电5. wiring installation is complete, test with a mul