组装,冲压,喷漆等专业词汇

1、组装,冲压,喷漆等专业词汇 组装、冲压、喷漆等专业词汇Assembly line 组装线 Layout布置图 Conveyer流水线物料板 Rivet table 拉钉机 Rivet gun拉钉枪 Screw driver 起子Electric screw driver 电动起子 Pworktable工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧（螺丝） fixture夹具（治具） pallet栈板barcode条形码barcode scanner条形码扫描 仪fuse together 熔合 fuse machine 热熔机 repair修理 operator

2、作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技fcosmetic inspect 外观检查 inner parts inspect 内部检查 thumb screw大头螺丝 ibs.hich镑、英寸 邮II gasket导电条 front plate 前板 rear plate 后板 chassis I* Zaesisl 基座 bezel panel 面板 power button电源按键 reset button 重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接校键 sheet metal parts 冲

3、件 plastic parts 塑料件 SOP制造作业程序 material check list 物料检查表 work cell工作间 trolley 台车 carton纸箱 sub-line 支线 left fork 叉车Personnel resourcedepartment 人力资源部 production department 生产部门 planning department 企划部 QC Section品管科 stamping factory 冲压厂 painting factory 烤漆厂 molding factory 成型厂 common equipment 常用设备 unc

4、oiler and straightener 整平机 punching machine 冲床 robot机械手 hydraulic machine 油压机 lathe车床 planei* rpleigl 刨床 miller铳床 grinder 磨床 driller 钻床 linear cutting 线切割 electrical sparkle 电火花 welder电焊机 staker=revlting machine 钾合机 position 职务 president董事长 general manager 总经理 special assistant manager 特助 factory di

5、rector 厂长 department director 部长 deputy manager rdepjutil =vice manager 副理 section supervisor 课长 deputy section suspensor =vice section supervisor 副课长 group leader/supervisor 组长 line supervisor 线长 assistant manager 助理 to move, to carry, to handle 搬运 be put in storage 入库 pack packing 包装 to apply oil

6、擦油 to file burr 锂毛刺 final inspection 终检 to connect material 接料 to reverse material 翻料 wet station 沾湿台 Tiana天那水 cleaning cloth 抹布 to load material 上料 to unload material 卸料 to return material/stock to 退 料scraped Fskraepidl报废 scrape .v刮消!） deficient purchase 来料不良 manufacture procedure 制程 deficient nian

7、ufacturing procedure制程不良 oxidation r ksPdeianl氧化 scratch 刮伤dents压痕defective upsiding down 抽芽不良 defective to staking 钾合不良embedded lumplinedl llAmpI镶块feeding is not in place 送料不到位 stamping-missing 漏冲 production capacity 生产力 education and training 教育与训练 proposal Improvement 提案改善 spare parts=buffer 备件 f

8、orklift 叉车trailer=long vehicle 拖板车 compound die 合模die locker锁模器pressure plate=plate pinch 压板bolt螺栓name of a department 部门名称 administration/general affairs dept总务部automatic screwdriver 电动启子 thickness gauge 厚薄规 gauge（oijlg）治具power wire电源线 buzzer蜂鸣器defective product label 不良标 签identifying sheet list 标示

9、单 screwdriver holder 起子插座 pedal踩踏板stopper阻挡器flow board流水板hydraulic hand Jack 油压板车 forklift 叉车pallet栈板glove（s）手套gthumb大拇指forefinger 食指 midfinger 中指 Hng Anger无名指 little finger 小指 band-aid创可贴 industrial alcohol 工业酒精 alcohol container 沾湿台 head of screwdriver 起子头 sweeper 扫把mop拖把vacuum cleaner 吸尘器 rag抹布ga

10、rbage container 灰箕 garbage can 垃圾箱 garbage bag 垃圾袋 chain链条Jack升降机production line 流水线 chain链条槽magnetizer 加磁器 lamp holder 灯架 to mop the floor 拖地 to clean the floor 扫地 to clean a table 擦桌子 air pipe 气管 packaging tool 打包机 packaging 打包 missing part 漏件 wrong part 错件excessive defects 过多的缺陷 critical defect极严

11、重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard 不合规格 dimensioii/size is a little bigger 尺寸偏大（小） cosmetic defect 外观不良 slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shipper screw thread 滑手 speckle 斑点mildewed=moldy=moldy 发霉 rust生锈 deformation 变形burr（金属）flash（塑件）毛边 poor staking钾合不

12、良 excessive gap间隙过大 grease/oil stains 油污 inclusion 杂质 painting peel off 脏污 shrinking/shrinkage 缩水 mixed color 杂色 scratch 划伤 poor processing 制程不良 poor incoming part 事件不良 fold of packaging belt 打包带折 皱painting make-up 补漆 discoloration 羿色 water spots 水渍Pexposed inetal/bare metal 金属裸露 lack of painting烤漆不

13、到位 fcafety安全 quality 品质Helivery deadline 交货期 tost成本 engineering 工程 ie repair 模修Enterprise plan = enterprise expansion projects 企划 QC品管 die worker 模工 production, to produce 生产 equipment 设备 to start a press 开机 stop/switch off a press 关机 classification 整理 pegulation 整顿 cleanness 清扫oconservation 清洁cultu

14、re 教养qualified products, up-to-grade products 良品 defective products, not up-to-grade products 不良品waste废料board看板feeder送料机sliding rack 滑料架defective product box 不良品箱die change 换模to fix a die 装模to take apart a die 拆模to repair a die 修模packing material 包材basket蝴蝶竺plastic basket 胶筐isolating plate baffle pl

15、ate;barricade 隔板carton box 纸箱to pull and stretch 拉深to put material in place, to cutmaterial, to input 落料to impose lines 压线to compress, compressing 压缩character die 字模to feed, feeding 送料transportation 运输(be)qualified9 up to grade 合格 not up to grade, not qualified 不 合格material change, stock change材料变更f

16、eature change 特性变更evaluation 评估prepare for, make preparationsfor准备parameters 参数rotating speed, revolution 转速 manufacture management 制造 管理abnormal handling 异常处理 production unit 生产单位 lots of production 生产批量 steel plate 钢板roll material 卷料manufacture procedure 制程 operation procedure 作业流程 to revise, modi

17、fy 修订to switch over to, switch一to throw-over switching over 切换 engineering, project difficulty工程瓶颈stage die工程模automation 自动化to stake, staking, revising 钾合 add lubricating oil 加润滑油 shut die 架模shut height of a die 架模高度 analog-mode device 类模器 die lifter举模器argon welding 氮焊vocabulary for stamping冲压常词汇sta

18、mping, press 冲压punch press, dieing out press 冲床uncoiler & strengthener 整平机feeder送料机rack, shelf, stack 料架cylinder 油缸robot机械手taker取料机conveyer belt 输送带transmission rack 输送架 top stop上死点bottom stop 下死点4one stroke 一行程inch寸动to continue, cont连动to grip(material)吸料 location lump, locating piece, block stop定位块

19、reset复位smoothly 顺利dent压痕scratch 刮伤deformation 变形filings铁削to draw holes 抽孔 inquiry, search for 查寻 to stock, storage, in stock 库存 receive 领取approval examine and verify 审核 processing, to process 加工 delivery, to deliver 交货 to return delivery to. to send dregistration 登记tegistration card 登记卡 to control 管

20、制to put forward and hand in 提报 safe stock安全库存 acceptance = receive 验收 to notice 通知afnnsume, consumption 消耗加fill in填写hbrasion 磨损keverse angle = chamfer 倒角 character die 字模 to collect, to gather 收集 failure, trouble 故障 statistics 统计demand and supply 需求 aareer card 履历卡tfiDn to take apart a die 卸下模具 to l

21、oad a die装上模具 to tight a bolt拧紧螺栓 to looser a bolt 拧松螺栓 to move away a die plate 移走模板 easily damaged parts 易损件 standard parts 标准件 breaking.(be)broken/be)cracked 断裂to lubricate 润滑 common vocabulary for die engineering模具工程常用词汇 die模具 figure file, chart file 图档 cutting die, blanking die 冲裁模 progressive

22、die, follow (-on)die 连续模 compound die 复合模 punched hole 冲孔 panel board 镶块 to cut edges=side cut=side scrap 切边to bending 折弯 to pull, to stretch 拉彳申 Line strengthen, line pulling 线拉 伸engraving, to engrave 刻印 upsiding down edges 翻边 to stake 钾合 designings to design 设计 design modification 设计变化 die block 模

23、块 folded block 折弯块 sliding block 滑块 location pin 定位销 lifting pin 顶料销 die plate, front board 模板 padding block 垫块 stepping bar 垫条lipper die base 上模座 lower die base 下模座 lipper supporting blank 上承 板lipper padding plate blank 上 垫板spare dies模具备品 spring弹簧bolt螺栓document folder 活页夹file folder 资料夹to put file

24、in order 整理资料 spare tools location 手工备品仓 first count 初盘人first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment 设备waste materials 废料work in progress product 在制品 casing = containerization 装箱 quantity of physical inventory second count复盘点数量 quantity of customs count 会计师盘,点数量 the first page 第一联fi

25、led by accountingdepartment for reference 会计 部存查end-user/iising imit(departmeiit)使用单位 summary of year-end physicalInventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK willbe sent to flnancial department)本表请与盘点清册一起送

26、会计 部一(NHK厂区送财会部) Application status records of year-end physical inventonr List and physical inventory card 年终盘点卡与清册使 用一状况明细表blank and waste sheet NO.空白与作废单号plate电镀 mold成型 material for engineering mold testing工程试模材料not included in physical inventory不列入盘点 sample样品incoming material to be Inspected进货待验

27、 description 品名 steel/rolled steel 钢材 material statistics sheet 物料统计明细表meeting minutes 会议记录 meeting type 会别 distribution department 分发 单位location 地点 chairman 主席 present members 出席人员 subject 主题conclusion 结论decision iteins 决议事项 responsible department 负责 单位pre-fixed finishing date 预定完成日 approved by / c

28、hecked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机钟work order 工令revision 版次remark备注production control confirmation生产确认checked by 初审approved by 核准 department 部门 stock age analysis sheet 库存货龄分析表on-hand inventory 现有库存 available material 良品可使用 obsolete material 良品已呆滞

29、to be inspected or reworked 待验或重工total合计cause description 原因说明 part number/ P/N 料号type形态iteni/group/class 类别quality 品质prepared by 制表notes说明year-end physical inventorydifference analysis sheetV年终盘点差异分析表physical inventor)-盘点数量 physical count quantity 帐面数 量difference quantity 差异量 cause analysis 原因分析 ra

30、w materials 原料materials 物料finished product 成品 semi-finished product 半成品 packing materials 包材 good product/accepted goods/ accepted parts/good parts 良品 defective product/non-good parts不良品disposed goods 处理品 warehouse/hub 仓库 on way location 在途仓 oversea location 海外仓 spare parts physical inventory list备品

31、盘点清单spare molds location 模具备品仓 skid/pallet 栈板 tox machine 自钾机wire EDM 线割EDM放电机coil stock 卷料sheet stock 片料tolerance 工差score=groove 压线 cam block 滑块 pilot导正筒 trim剪外边 pierce剪内边 drag form压锻差pocket for the punch head 挂钩 槽Slug hole废料孔feature die 公母模expansion dwg 展开图 radius半径shim(wedge)楔子torch-flame cut 火焰切

32、割 set screw止付螺丝 form block 折刀 stop pin定位销round pierce punch=diebutton圆冲子shape punch=die insert 异形子 stock locater block 定位块 under cut=scrap chopper 清角 active plate 活动板 battle plate 挡块 cover plate 盖板 male die 公模female die 母模groove punch压线冲子air-cushion eject-rod 气垫顶杆 spring-box eject-plate 弹簧箱顶 板bushin

33、g block 衬套Insert入块club car高尔夫球车capability 能力parameter 参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping 脱脂 main manifold主集流脉 bezel斜视规blanking穿落模dejecting顶固模demagnetization 去磁;消磁 high-speed transmission 高速传 递heat dissipation 热传rack上料degrease 脱脂rinse水洗alkaline etch 龄咬demit剥黑膜D.I. rinse纯水次Chromate辂酸处理A

34、nodize阳性处理seal封孔revision 版次part number/P/N 料号good products 良品 scraped products 报放心品 defective products 不良品 finished products 成品 disposed products 处理品 barcode条形码 flow chart流程窗体 assembly 组装 stamping 冲压 molding 成型 spare parts=buffer 备品 coordinate 坐标 dismantle the die 折模 auxiliary function 辅助功能 poly-lin

35、e多义线 heater band 力口热片 thermocouple 热电偶 sand blasting 喷沙 grit砂砾 degusting machine 除锈机 debate 打浇 口 dryer烘干机 induction 感应 induction light 感应光 response=reaction=interaction 感应ram连杆edge finder 巡边器 concave 凸 convex 凹 short射料不足 nick 缺口 speck瑕疵 shine亮班 splay银纹 gas mark 焦痕 delamination 起鳞 cold slug 冷块 blush导

36、色gouge沟槽;凿槽volatile挥发性satin texture段面咬花resistance 电阻witness line 证示线ion离子patent专利titrator滴定仪grit沙砾beacon警示灯granule=poet=grain 细粒coolant冷却液grit maker抽粒机crusher破碎机cushion 缓冲模具工程类magnalium镁铝合金plain die简易模magnesium 镁金pierce die冲孔模metal plate 镀金forming die 成型模lathe 车progressive die 连续模mill 铿gang dies复合模p

37、lane 刨shearing die 剪边模grind 磨riveting die 钟合模drill 铝pierce冲孔boring 镇forming成型（抽凸，冲凸）blister 气泡draw hole 抽孔fillet镇;嵌边bending 折弯through-hole form 通孔形式trim切边volley pin formality 滚针形式emboss凸点cam driver 锄楔dome凸圆shank摸柄semi-shearing 半剪crank shaft 曲柄轴stamp mark冲记号angular offset 角度偏差deburr or coin 压毛边veloci

38、ty 速度punch riveting 冲压钾合production tempo生产进度现状side stretch侧冲压平torque扭矩reel stretch卷圆压平spline=the multiple keys 花键groove压线quenching 淬火blanking 下料tempering 回火stamp letter 冲字（料号）annealing 退火shearing 剪断carbonization 碳化tick-mark nearside 正面压印alloy合金tick-mark farside 反面压印tungsten high speed steel 铝高速的冲压名称

39、类moly high speed steel 铝高速的extension dwg 展开图organic solvent 有机溶剂procedure dwg 工程图bracket小磁导die structure dwg模具结构图liaison联络单material 材质material thickness 料片厚度 factor系数upward向上downward 向下press specification 冲床规格 die height range 适用模高 die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt上模重量五金零件类inner

40、guiding post 内导柱inner hexagon screw 内六角螺钉 dowel pin固定销 coil spring 弹簧 lifter pin顶料销eq-height sleeves=spool 等高套筒 pin销lifter guide pin浮升导料销 guide pin导正销 wire spring圆线弹簧 outer guiding post 外导柱 stop screw止付螺丝 located pin 定位销 outer bush夕卜导套 模板类top plate上托板（顶板） top block上垫脚 punch set上模座 punch pad上垫板 punch

41、 holder 上夹板 stripper pad脱料背板 up stripper上脱料板 male die公模（凸模） feature die 公母模 female die母模（凹模） upper plate 上模板lower plate 下模板die pad下垫板die holder下夹板die set下模座bottom block 下垫脚bottom plate下托板（底板） stripping plate内外打（脱料板） outer stripper 外脱料板 inner stripper 内脱料板 lower stripper 下脱料板 零件类punch冲头insert入块（嵌入件）d

42、eburring punch压毛边冲子 groove punch压线冲子 stamped punch字模冲子 round punch 圆冲子 special shape punch 异形冲子 bending block 折刀roller滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板 air-cushion eject-rod 气垫顶杆 trimming punch 切边冲子 stiffening rib punch = stinger 加强筋冲子ribbon pu

43、nch压筋冲子 reel-stretch punch卷圆压平冲子 guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块 active plate 活动板lower sliding plate 下滑块板 upper holder block 上压块 lipper mid plate 上中间板 spring box弹簧箱spring-box eject-rod 弹簧箱顶杆 spring-box eject-plate 弹簧箱顶 板bushing block 衬套cover plate 盖板guide pad导料块塑件&模具相关英文 com

44、press sion molding 压缩成 型flash mold溢流式模具 plsitive mold挤压式模具 split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak 仿皮革shiver饰纹flow mark 流痕welding mark 溶合痕post screw insert螺纹套筒埋值 self tapping screw 自攻螺丝 striper plate 脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具e射出成型用模具two plate两极式（模具）ell type蓄料

45、井Insulated runner绝缘浇道方式hot runner热浇道tunner plat浇道模块naive gate 阀门浇口band heater环带状的电热器Spindle 阀针spear head刨尖头 quality controlAnal quality control in process quality control output quality control incoming quality control total quality control passage quality control quality assurance output quality as

46、surance quality engineeringfirst article inspection first article assurance tool verification report 3Bcapability index capability index of process standardized supplier quality out of box auditquality function deployment failure model effectiveness analysis8 disciplines品质管理人员终点品质管制人员 制程中的品质管制人员 最终出

47、货品质管制人员 进料品质管制人员 全面质量管理 段检人员 质量保证人员 出货质量保证人员 品质工程人员新品首件检查 首件确认 模具确认报告 模具正式投产前确认 能力指数模具制程能力参数 合格供货商品质评估 开箱检查品质机能展开 失效模式分析 8项回复内容slag well冷料井 cold slag冷料渣 air vent排气道 h=0.020.05mm w=3.2mmL=351nm welding line 熔合痕 eject pin顶出专f knock pin顶出销 return pin回位销反顶针 sleave套筒 stripper plate 脱料板 insert core放置入子 ru

48、nner stripper plate 浇道脱 料板 guide pin 导销 品质人员名称类 QC FQC IPQC OQC IQC TQC POC QA OQA QE 品质保证类 FAI FAA TVR 3B CP CPK SSQA OOBA QFD FMEA 8Deject rod （bar）（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation 定向sprue gate射料浇口,直浇口nozzle射嘴sprue lock pin料头钩销（拉料杆）slag well冷料井side ga

49、te 侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口 fan gate扇形浇口 dish gate因盘形浇口 H=F=l/2t-l/5tT=2.53.5mmdiaphragm gate 隔膜浇口 ring gate环形浇口 submarine gate 潜入式浇 口 tunnel gate隧道式浇口 pin gate针点浇口 d0.8-1.0mmRunner less 无浇道(sprue less)无射料管方式 long nozzle延长喷嘴方式 sprue浇口;溶渣FAfinal audit最后一次稽核

50、CARcorrective action request改正行动要求corrective action report改正行动报告FQC运作类AQLAcceptable Quality Level运作类允收品质水准S/SSample size抽样检验样本大小ACCAccept允收REEReject拒收CRCritical极严重的MAJMajor主要的MINMinor轻微的AOQAverage Output Quality平均出厂品质AOQLAverage Output Quality Level平均出厂品质Q/R/SQualitv/Reliabilitv/Service品质何靠度服务MIL-ST

51、DMilitary-Standard军用标准S I-S IVSpecial I-Special IV特殊抽样水准等级P/NPart Number料号L/NLot Number特采AODAccept On Deviation特采UAIUse As It首件检查报告FPIRFirst Piece Inspection Report百万分之一PPMPercent Per Million批号制程统计品管专类SPCStatistical Process Control统计制程管制SQCStatistical Quality Control统计品质管制RRange全距ARAverary Range全距平均

52、值UCLUpper Central Limit管制上限LCLLower Central Limit管制下限MAXMaximum最大值MINMinimum最小值GRRGauge Reproducibility & Repeatability量具之再制性及重测性判断量可靠与否DIMDimension尺寸DIADiameter直径FREQFrequency频率NNumber样品数其它品质术语类QCCQuality Control Circle品质圈QITQuality Improvement Team品质改善小组PDCAPlan Do Check Action计划执行检查总结ZDZero Defec

53、t零缺点QIQuality Improvement品质改善QPQuality Policy目标方针TQMTotal Quality Management全面品质管理MRBMaterial Reject Bill退货单LQLLimiting Quality Level最低品质水准RMAReturn Material Audit退料认可QANQuality Amellonrate Notice品质改善活动ADMAbsolute Dimension Measuremat全尺寸测量QTQuality Target品质目标7QCTools7 Quality Controll Tools品管七大手法通用之

54、件类ECNEngineering Change Notes工程变更通知（供货商）ECOEngineering Change Order工程改动要求（客户）PCNProcess Change Notice工序改动通知PMPProduct Management Plan生产管制计划SIPSpecification In Process制程检验规格SOPStandard Operation Procedure制造作业规范ISInspection Specification成品检验规范BOMBill Of Material物料清单PSPackage Specification包装规范SPECSpeci

55、fication规格DWGDrawing图面系统文件类QCQuality System品质系统ESEngineering Standarization工程标准CGOOChina GeneralPCE龙华厂文件HHuston（美国）休斯敦CCompaq（美国）康伯公司CChina中国大陆AAssembly组装（厂）SStamping冲压（厂）pPainting烤漆（厂）IIntel英特尔公司TTAIWAN台湾IWSInternational Workman Standard工艺标准ISOInternational Standard Organization国际标准化组织GSGeneral Spe

56、cification一般规格CMCSC-China M-Manufact C-Compaq S-StampingCompaq产品在龙华冲压厂制造作业规范CQCAQ-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCPP-PaintingCompaq产品在龙华烤漆厂品管作业规范部类PMCProduction & Material Control生产和物料控制PPCProduction Plan Control生产计划控制MCMaterial Control物料控制MEManafacture Engineering制造工程部PEProject Engineering

57、产品工程部A/CAccountant Dept会计部P/APersonal & Administration人事行政部DCDocument Center资料中心QEQuality Engineering品质工程（部）QAQuality Assurance品质保证（处）QCQuality Control品质管制（课）PDProduct Department生产部LABLabratry实验室IEIndustrial Engineering工业工程R&DResearch & Design设计开发部PPainting烤漆（厂）AAsssemblv组装（厂）sStamping冲压（厂）生产类PCSPie

58、ces个（根,块等）PRSPairs双（对等）CTNCarton卡通箱PALPallet/skid栈板POPurchasing Order采购订单MOManufacture Order生产单D/CDate Code生产日期码ID/CIdentification Code（供货商）识别码SWRSpecial Work Request特殊工作需求L/NLot Number批号P/NPart Number料号其它OEMOriginal Equipment Manufacture原设备制造PCEPersonal Computer Enclosure个人计算机外设PCPersonal Computer个

59、人计算机CPUCentral Processing Unit中央处理器SECCSECC电解片SGCCSGCC热浸镀锌材料NHKNorth of Hongkong中国大陆PRCPeoples Republic of China中国大陆U.S.Athe United States of America美国A.S.A.PAs Soon As Possible尽可能快的E-MAILElectrical-Mail电子邮件N/ANot Applicable不适用QTYQuantity数量VS以及REVRevision版本JITJust In Time零库存I/OInput/Output输入检出OKOk好NGNot Good不行,不合格C=0Critical=O极严重不允许ESDElectry-static Discharge静电排放5S希腊语整理，整顿，清扫，清洁，教养ATINAttention知会CCCarbon Copy副本复印相关人员APPApprove核准，认可，承认CHKCheck确认AMAnte Meridian上午PMPost Meridian下午CDCompact