常见故障及解决办法

1、N1nyu扫描O到IPN1nyu扫描O到IP地址，或控制器24V断电后IP地址重置System级别进入 6000通设置将HICP-config设DHCP选项设off,防k控制器断电后IP地址重2012-04-01| Department | chGs, also regarding anyal, exploi ion, reproduction,editing, distribution,aswell as1the event of applications for industrial property 二1无电流解决办法检查O项380进电电二1无电流解决办法检查O项380进电电压，确保电压

2、稳定，无缺相11动力电缆21电极帽之间有更换电极帽，保证焊接回路闭31l级电流传感器故将电流测量模式更改2012-04-01| Department | chGs, also regarding anyal, exploi ion, reproduction,editing, distribution,aswell as2the event of applications for industrial property 二1无电流解决办法二1无电流解决办法41动力电缆和信号电缆接2012-04-01 | chGs, also regarding anyal, exploi ion, repro

3、duction,editing,distribution,as well as3the event of applications for industrial property 二1无电流解决办法控制器X22,4脚需要压力二1无电流解决办法控制器X22,4脚需要压力反馈信号，X2-20V, X2-424V2对于PSI63C0.177手控制器输入E11,E15压力检测必须高电平2现场有51控制器没有检测到压力分焊枪没有对这两个信号做定义压力检测开关2012-04-01 | chGs, also regarding anyal, exploi ion, reproduction,editing,

4、distribution,as well as4the event of applications for industrial property O1空开无法合解决办法将急停按钮11O1空开无法合解决办法将急停按钮11焊枪急停按钮被拍21k压保线圈DD脚24v查回路，测量线圈电阻，l常在26欧姆2012-04-01 | chGs, also regarding anyal, exploi ion, reproduction,editing,distribution,as well as5the event of applications for industrial property O1空

5、开无法合解决办法将控制柜用哈OO1空开无法合解决办法将控制柜用哈O短接，判定漏电发生在哪N31漏电检测仪有漏电漏电检测仪，面P3个LED灯从右别电源灯1漏灯1漏电2012-04-01 | chGs, also regarding anyal, exploi ion, reproduction,editing,distribution,as well as6the event of applications for industrial property 四1电磁阀O解决办法检查11四1电磁阀O解决办法检查11电磁阀没有得到21焊接程序没有设定压力对焊接程序设置l确的压2012-04-01 |

6、chGs, also regarding anyal, exploi ion, reproduction,editing,distribution,as well as7the event of applications for industrial property 五1外部超温解决办法短接X3的五1外部超温解决办法短接X3的4，511变压器温度传感器未接入控制器控制器端未2012-04-01 | chGs, also regarding anyal, exploi ion, reproduction,editing,distribution,as well as8the event of

7、applications for industrial property 五1外部超温因11对于五1外部超温因11对于手控制柜，水流量检测灯决2012-04-01 SLF|chGs, alsoregarding anyal,exploi ion, reproduction,editing,distribution,aswellas9the event of applications for industrial property 六1变压器温度解决办法六1变压器温度解决办法11变压温度触电断2012-04-01 | chGs, also regarding anyal, exploi ion,

8、 reproduction,editing,distribution,as well asthe event of applications for industrial property 六1变压器温度解决办法控制器压力开关P变压六1变压器温度解决办法控制器压力开关P变压器温度传感器是串联的，当进气压力P于阀值时，警信息也变压器温度过高=，可以调节压力开关部内六角变阀值11总进气压力P于压力开关设定阀2012-04-01 | chGs, also regarding anyal, ion, reproduction, editing, distribution, as well asthe

9、event of applications for industrial property 七erbus通OP(MQB之前的333/336控制器解决办法1通速率设置Ol七erbus通OP(MQB之前的333/336控制器解决办法1通速率设置Ol在erbusP的DIP开关，S1-S5是定义字节度，S8是定义通速率，OFF是2M baud,ON是 500Kb d2在控制器P的ADR要拨r非0，才1总线地址 SLF| chGs,alsoregardinganyal,exploi ion,reproduction,editing,distribution,aswellastheeventofapplicationsforindustrialproperty七1控制器没有焊接完r解决办法将启动信号的时长设置七1控制器没有焊接完r解决办法将启动信号的时长设置大于预压时间11启动信号八1控制器修磨点数无法复O，电极已修磨信号=已发解决办法11修磨程序电