资源目录
压缩包内文档预览:
编号:86410610
类型:共享资源
大小:296.45KB
格式:RAR
上传时间:2020-06-16
上传人:加Q294****549海量...
认证信息
个人认证
乐**(实名认证)
湖南
IP属地:湖南
39
积分
- 关 键 词:
-
3810
长筒塑料制品注塑模设计
塑料制品
注塑
设计
- 资源描述:
-
3810 长筒塑料制品注塑模设计,3810,长筒塑料制品注塑模设计,塑料制品,注塑,设计
- 内容简介:
-
河南机电高等专科学校材料工程系模具设计与制造毕业设计/论文设计/论文题目:长筒注塑模的设计 班 级: 模具033班 姓 名: 陈振倩 指导老师: 杨占尧 完成时间: 2006年05月 毕业设计(论文)成绩毕业设计成绩指导老师认定成绩小组答辩成绩答辩成绩指导老师签字答辩委员会签字答辩委员会主任签字毕业设计/论文任务书 题目:长筒零件的成型工艺及塑料模具设计 内容:(1)模塑工艺规程的编制(2)确定分型面(3)浇注系统的确定(4)成型零件的结构设计(5)成型零件的结构设计(6)冷却加热系统的设计原始资料: 设计题目:长筒注塑模材料:FRPP生产批量:大批量生产插图清单图1.1 产品零件图图2.1 主流道图2.2 定位圈图2.3 斜导柱表格清单表2-1 尺寸与模具成型零件工作尺寸的取值规定表2-2 成型零件工作尺寸计算公式表2-3 型芯计算表表2-4 型腔计算表表4-1 模具典型零件机械加工工序卡 (毕业设计/论文题目) 摘要( 中文)启模前,减速器1应先工作,靠过渡齿轮10,齿轮14,大过渡齿轮15和转动将丝芯13转动,由于型套24上设有M28*2导向螺纹,迫使丝芯同步后退,从制品中脱出.再开启模具,”A-A”面分型,制品连同主型芯从动模板25中抽出,最后,在拉条21和六角螺钉9的作用下,拉动推板18,”B-B”面分型,同时斜导柱19工作,将哈夫滑块17侧分析,即实现脱模.另外,浇口由”A-A”分型面从两侧注入型腔,避免细长型芯受冲击而产生弯曲造成制品壁厚不均匀.该模具为倒装模具是为了保证导向精度准确,保证制品精度.塑件外形复杂对型腔黏附力较大.为了使塑件不至于留在定模一侧,应该将型腔设置在动模一侧.关键词: 模具 型芯 型腔 动模板 分型面 (毕业设计/论文英文题目) Abstractmold front, decelerate the machine 1 should work first, depend the transition wheel gear 10, wheel gear 14, big transition wheel gear 15 with turn to move the silk 13 turn to move, because of type set 24 ascend establish the M28*2 lead to thread, force the synchronous countermarch in in silk, take off from product.Open again the molding tool, cent in in A- A type, product to draw out from move the template 25 together with the main type , finally, while pulling a function for 21 with hexangular bolt 9, pull to move to push the plank 18, B- B cent type, inclined at the same time lead the pillar 19 work, slippery piece in the man of 17 sides analyze, then realizes to take off the mold.Moreover, sprinkle be divided by A- A type from two sides infuse into the type , avoiding the thin long type 芯 suffer the impact but creation the flection results in the thick asymmetry in wall in ware.That molding tool is set up wrong molding tool is for guaranteeing to lead to the accuracy is accurate, guaranteeing the ware accuracy.The a shape complicacy sticks to attaching the dint to the type bigger.For making the piece of stayed not to the extent of at settle the mold a side, should establ
- 温馨提示:
1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。图纸软件为CAD,CAXA,PROE,UG,SolidWorks等.压缩文件请下载最新的WinRAR软件解压。
2: 本站的文档不包含任何第三方提供的附件图纸等,如果需要附件,请联系上传者。文件的所有权益归上传用户所有。
3.本站RAR压缩包中若带图纸,网页内容里面会有图纸预览,若没有图纸预览就没有图纸。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 人人文库网仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对用户上传分享的文档内容本身不做任何修改或编辑,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

人人文库网所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。