热熔胶MSDS英文版.doc

SAFETY DATA SHEETPRODUCT NAME:HOT MELT ADHESIVE FOR AUTOMOBILE LAMPS 1 CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONPRODUCTProduct Name: HOT MELT ADHESIVE FOR AUTOMOBILE LAMPSProduct Description: HOT MELT ADHESIVE,MIXTUREProduct Code: Intended Use: ADHESIVE,FOR AUTOMOBILE LAMPSCOMPANY IDENTIFICATIONSUPPLIER:Huangshan Xiuning Xindecheng Chemical Co., Ltd.Wanning Industrial Park, Huangshan, Anhui, China (245400)Telephone: 0086-559-7519970Facsimile: 0086-559-7519971This (M)SDS is a generic document with no country specific information included.2 COMPOSITION/INFORMATION ON INGREDIENTSNo Reportable Hazardous Substance(s) or Complex Substance(s). INGREDIENTSCAS No.Approx. Proportionstyrene butadiene rubber9003-55-8Med 50-60%rosin resin8050-09-7Low 50-40%3 HAZARDS IDENTIFICATIONThis material is not considered to be hazardous.PHYSICAL / CHEMICAL HAZARDSN/A HEALTH HAZARDSl No adverse effects due to inhalation are expected. When heated, the vapour/fumes given off may cause respiratory tract irritation.4 FIRST AID MEASURESINHALATIONl In case of adverse exposure to vapors and / or aerosols formed at elevated temperatures, immediately remove the affected victim from exposure. Administer artificial respiration if breathing is stopped. Keep at rest.SKIN CONTACTl Wash contact areas with soap and water. For hot product: Immediately immerse in or flush affected area with large amounts of cold water to dissipate heat. Cover with clean cotton sheeting or gauze and get prompt medical attention.EYE CONTACTl Flush thoroughly with water. If irritation occurs, get medical assistance.INGESTIONl First aid is normally not required. Seek medical attention if discomfort occurs.5 FIRE- FIGHTING MEASURESEXTINGUISHING MEDIAl Appropriate Extinguishing Media: Use dry chemical or carbon dioxide (CO2) to extinguish flames.l Inappropriate Extinguishing Media: Straight streams of waterFIRE FIGHTINGl Fire Fighting Instructions: Assure an extended cooling down period to prevent re-ignition. Evacuate area. Prevent run-off from fire control or dilution from entering streams, sewers or drinking water supply. l Hazardous Combustion Products: Flammable hydrocarbons, Oxides of carbon, Smoke, Fume, Incomplete combustion products 6 ACCIDENTAL RELEASE MEASURESNOTIFICATION PROCEDURESl In the event of a spill or accidental release, notify relevant authorities in accordance with all applicable regulations.ENVIRONMENTAL PRECAUTIONSN/A 7 HANDLING AND STORAGEHANDLINGl Avoid elevated temperatures for prolonged periods of time. Protect material from direct sunlight. Material can accumulate static charges which may cause an electrical spark (ignition source). Apart from the specific nature of the polymer product, conditions such as humidity, sunlight and temperature.l Loading/Unloading Temperature: Ambientl Transport Temperature: Ambient STORAGEl Store in a cool, dry place. l Storage Temperature: 040l Storage Pressure: Ambient 8 EXPOSURE CONTROLS /PERSONAL PROTECTIONENGINEERING CONTROLSN/APERSONAL PROTECTIONl Personal protective equipment selections vary based on potential exposure conditions such as applications, handling practices, concentration and ventilation. Information on the selection of protective equipment for use with this material, as provided below, is based upon intended, normal usage. Respiratory Protection: l If engineering controls do not maintain airborne contaminant concentrations at a level which is adequate to protect worker health, an approved respirator may be appropriate. Respirator selection, use, and maintenance must be in accordance with regulatory requirements, if applicable. Types of respirators to be considered for this material include: l No special requirements under ordinary conditions of use and with adequate ventilation. l For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode. Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate, gas/vapour warning properties are poor, or if air purifying filter capacity/rating may be exceeded.Hand Protection: l If product is hot, thermally protective gloves are recommended. If contact with forearms is likely, wear gauntlet style gloves. Eye Protection: l If contact is likely, safety glasses with side shields are recommended.Skin and Body Protection: l If product is hot, thermally protective, chemical resistant apron and long sleeves are recommended.Specific Hygiene Measures: l Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned. Practice good housekeeping.9 PHYSICAL AND CHEMICAL PROPERTIESTypical physical and chemical properties are given below. Consult the Supplier in Section 1 for additional data.GENERAL INFORMATIONl Physical State: Solidl Form: Grainsl Colour: Grayl Odour: None to MildIMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATIONl Relative Density (at 18 C): 0.97 l Density (at 18 C): 970 kg/ml Flash Point method: O.C Cleveland Open Cup 260l Flammable Limits (Approximate volume % in air): LEL: N/D UEL: N/D l Autoignition Temperature: N/A l Boiling Point / Range: 260l Vapour Density (Air = 1): N/Al Vapour Pressure: N/Al Evaporation Rate (N-Butyl Acetate = 1): N/Al pH: N/Al Log Pow (n-Octanol/Water Partition Coefficient): N/Al Solubility in Water: Negligible10 STABILITY AND REACTIVITYSTABILITY: l Material is stable under normal conditions.CONDITIONS TO AVOID: l Avoid elevated temperatures for prolonged periods of time.HAZARDOUS DECOMPOSITION PRODUCTS: l Material does not decompose at ambient temperatures.HAZARDOUS POLYMERIZATION: l Will not occur.11 TOXICOLOGICAL INFORMATIONAcute Toxicity Route of Exposure Conclusion / RemarksINHALATIONToxicity: Minimally Toxic. Based on test data for structurally similar materials.Irritation: Negligible hazard at ambient/normal handling temperatures. Based on test data for structurally similar materials.INGESTIONToxicity: Minimally Toxic. Based on test data for structurally similar materials.SkinToxicity: Minimally Toxic. Based on test data for structurally similar materials.Irritation: Negligible irritation to skin at ambient temperatures. Based on test data for structurally similar materials.Eye Irritation: May cause mild, short-lasting discomfort to eyes. Based on test data for structurally similar materials.CHRONIC/OTHER EFFECTS12 ECOLOGICAL INFORMATIONThe information given is based on data available for the material, the components of the material, and similar materials.ECOTOXICITY l Material - Not expected to be harmful to aquatic organisms. l Material - Not expected to be harmful to terrestrial organisms13 DISPOSAL CONSIDERATIONSDisposal recommendations based on material as supplied. Disposal must be in accordance with current applicable laws and regulations, and material characteristics at time of disposal. DISPOSAL RECOMMENDATIONSl Suitable routes of disposal are supervised incineration, preferentially with energy recovery, or appropriate recycling methods in accordance with applicable regulations and material characteristics at the time of disposal. 14 TRANSPORT INFORMATIONLAND : Not Regulated for Land TransportSEA (IMDG) : Not Regulated for Sea Transport according to IMDG-CodeAIR (IATA) : Not Regulated for Air Transport15 RRGULATORY INFORMATIONMaterial is not hazardous as defined by the EU Dangerous Substances/Preparations Directives.16 OTHER INFORMATIONN/D = Not determined, N/A = Not applicableTHIS SDS COVERS THE FOLLOWING MATERIA